Search Documents

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

By Manfred Krutein

Ocean mining has a number of problems which are critical to its development: ? Political hurdles on national and international stages ? The worldwide economic situation, with the possibliity of a recession ? Financial difficulties in funding further work ? Technical problems for the development of ocean mining and transport subsystems ? Demands for technology transfer This paper touches the last two points and provides some thoughts for discussion and creative objectification. The many technical problems of ocean mining will be identified and some proposed solutions will be investigated relative to the state-of-the-art technology of ocean mining and nodule transport. An outlook into the future attempts identification of the steps necessary to eventually develop components for workable systems that are not only technically but also economically feasible.

Jan 1, 1978

By Julian Malnic

Various natural, commercial, engineering and operational factors govern the evolution of approaches taken in the exploration for Seafloor Massive Sulphides (SMS) and in delineating the resource. These stages are prerequisites to the proposed mining of SMS deposits. This paper presents and analyses these factors from the view of an SMS exploration company that is pioneering the exploration of this rich alternative source of zinc, copper and gold. Current exploration practices developed by Marine Scientific Research (MSR) workers for SMS deposits are expected to give way to industry-generated methods as the SMS exploration industry gathers momentum. The exploration process falls into three phases that are described below: Prospecting (locating targets), Indicating Resources, and Measuring Mineral Resources Considerable streamlining of the SMS exploration process will accelerate the rate of discovery. The economics of SMS mining are projected to be superior to comparable terrestrial mining operations in both operating cash cost and capital terms.

Jan 1, 2001

By Jan Willem van Bloois

IHC Merwede is world market leader in the construction of specialist dredging equipment; it is a company with a rich history. The Netherlands is a coastal western country for which water management is a very important issue. Without the enclosure of the coastal areas with dikes and dunes almost two third of the Netherlands would be flooded. These activities are mostly performed by the dredging industry and are the foundation of the dredging industry as it is today. Besides land protection this industry also carries out infrastructure maintenance and performs land reclamation projects. In essence the dredging industry is specialized in horizontal excavation activities and operations in shallow waters with the purpose of gathering bottom sediments and disposing it at a different location. The development is that the activities are moving to deeper waters to a depth of up to 150m. A few years ago IHC Merwede received a request to perform the shallow water excavation techniques at a depth of approximately 2000 meters for the deep sea mining market. In response to the increasing number of requests for deep sea dredging and mining application solutions, IHC Merwede combined all of its activities in this sector to create a new, specially equipped operational unit, IHC Deep Sea Dredging & Mining (IHC DSDM).

Jan 1, 2010

By NA UMC

Abstract Booklet

Dec 1, 2022

By NA UMC

Abstract Booklet

Dec 2, 2023

By J. A. Jankowski

The situation in the raw material market has brought into consideration the commercial exploitation of the mineral deposits on the deep sea bed and in particular the manganese nodules. They occur generally in depths of 4000-5000 m, partially covered or buried in bottom sediments. The deposits and their potential recovery have been intensively explored and researched during the past twenty years (Bischoff 1979, Halbach 1988, Padan 1990). Although the present market situation limits the rentability of deep sea mining on an industrial scale, the mining technology is being further developed in many countries. The stagnation phase in the deep mining issue allows sufficient time for conducting research on the precautionary protection of the deep sea environment and for consultation in the development of technologies with the least possible impact on it. The subject has gained in importance since autumn 1994, when the United Nations International Law of the Sea was signed. This also regulates human activities in international waters from the environmental point of view. As fields tests have shown in the past, even with the most modern technologies, mining of the manganese nodules will inevitably be accompanied by a resuspension of some bottom sediments. The generated sediment plumes will be further transported with the ocean currents and in the worst case form stable turbidity layers in different depths (Ozturgut 1981a, Baturin 1991). One of the problems of the environmental impact assessment is the estimation of the plume persistence before it eventually dilutes to approximately the ambient concentration level or settles at the bottom (Lavelle 1981a, Lavelle 1981b, Lavelle 1982, Thiel 1991a, Thiel 1991b). The aim of the research is to develop a numerical sediment transport model in connection with potential manganese nodule mining in a reference area located in the southeastern equatorial Pacific Ocean off Peru (Peru Basin, Discol Experimental Area). In this region, a German mining claim is registered and interdisciplinary field works of the TUSCH (German: TiefseeUmweltSCHutz, deep sea environmental protection) research group are carried out in order to obtain the required scientific background for evaluating of the deep sea mining impacts and to provide the necessary supporting data for the modelling (Thiel 1991a, Thiel 1991h).

Jan 1, 1995

By Cheng Xiangzhou

The China Ocean Mineral Resources Research and Development Association (COMRA) conducted a topographic survey in its deep seabed claim area with the SeaBeam system in 19475. After analyzing the data, it was determined that there is a group of living things several hundreds of meters in depth that significantly affect the sound waves in the frequency range of interest. We will attempt to investigate more about such influences. Physical model testing is an important means for studying the theory, and for development of the technology for geophysical prospecting. Because the manganese nodules are distributed over the sea floor in irregular patterns, it is hoped that study of the acoustic properties of manganese nodules by means of physical model testing can improve interpretation of the data of the multi-beam system and the SeaBeam system. This will provide a more reliable basis for delimiting the mineral site and evaluating the reserves in the Pioneer area of China.

Jan 1, 1996

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By Wenbin Ma, Cees van Rhee, Dingena Schott

Since the concept of deep sea mining (DSM) was proposed by J. L. Mero with his book, The Mineral Resources of the Sea, in the 1960s, many research and significant developments have been implemented. However, its commercial mining process still has not yet commenced. One of the most important issues is that a sustainable DSM transport plan is difficult to determine, taking into consideration the DSM technological, economic, and environmental aspects simultaneously. The objective of this paper is to propose a method to determine the sustainable DSM transport plan utilizing a fuzzy analytic network process method, which is a typical multi-criteria decision making method (MCDM). The DSM transport plans evaluating major criteria consist of technological, economic, environmental, and social aspects with both qualitative and quantitative attributes. Different major criteria include several sub-criteria, respectively:  Technological aspect: energy consumption, proven technology, technology reliability, production rate, technology availability;  Economic aspect: gross income, capital cost, operation and maintenance cost, investment recovery period;  Environmental aspect: species disturbance variance, severity of ill effect, turbidity of ocean water, total organic carbon content, sedimentation thickness;  Social aspect: social acceptability, policy support; The weights for all evaluating criteria and sub-criteria are determined through a questionnaire survey interviewing experts at different research fields. All the transport plan candidates are ranked based on a comprehensive index. The conducted research in this paper is meaningful to promote the DSM commercialization process.

Jan 1, 2018

By Hjalmar Thiel

Since industry is progressing into the deep sea, marine scientists have expressed their concern about environmental disturbances which will be introduced by using the deep seafloor for mining metalliferous resources or as a repository for wastes. Environmental studies have been conducted on national levels and in bilateral or multilateral cooperation in the development of manganese nodule mining, as this is generally achieved in marine research. These investigations were partly large-scale and experimental approaches aiming at the assessment of the impacts expected to occur in commercial mining. The results elaborated till today and expected to be acquired in the foreseeable future may remain limited. Reliable impact evaluation will result from monitoring a Pilot Mining Operation (PMO). The lecture will present the broad outlines of a possible program and a preliminary calculation of approximate costs for such a combined industrial test and environmental monitoring event. Although the extent of necessary efforts for the environmental risks evaluation can only be estimated rather vaguely, it will become evident that the required human, technical, logistical, and financial resources to be mobilized will exceed industrial capacities and go beyond national funds. Therefore, such assessment of environmental risks is calling for broad international cooperation. While industrial developments for mining the deep sea will be ruled by competition or probably by restricted joint ventures, environmental care ranges outside competition and falls within the interest of all parties involved. Environmental studies, unlike technologies for the same function, do not primarily need duplication. International cooperation in PMO monitoring would equally well support all mining companies or consortia, it would minimize the efforts for all engaged in this challenging venture of deep-sea mining and it would maximize the precautionary discussion on and the care for the deep-sea environment.

Jan 1, 1994

By Laurie Meyer

The need for improved, high confidence estimates of nodule abundance to support mine permitting, detailed mine planning and mining and processing equipment design is evident. To date, physical samples represent the ?Gold Standard? for nodule abundance measurement, and are likely to remain as such. However, there are some interesting improvements in the area of 3-D scanning which, if marinized for operations at 6000m, may prove to be reliable alternative methods for mapping abundance over large areas particularly if calibrated or benchmarked with physical sample data. . Features of a high confidence physical sampling device, such as the 0.75m2 (0.86m on a side) box corer developed and successfully used by the Kennecott Group for exploration in the CCZ, take into account not only the accuracy in nodule sample collection but a host of other operability considerations which can mean the difference between a successful exploration cruise yielding high numbers of large area samples and one in which few, inaccurate, often inconclusive samples are collected (or, even worse, the sampler fails to grab any nodules for any number of reasons). The collection of physical samples at appropriate spacing within a mine area combined with more qualitative indications of nodule density such as can be obtained using acoustic backscatter should prove adequate for the near term objectives related to overall abundance appraisal or estimates of ?indicated? resource. Looking ahead, exploration cruises will need to yield increasing amounts of data to support development of higher confidence resource abundance estimates to support issuance of mining permits and detailed design of mining plans and equipment. It is likely

Sep 14, 2011

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By Elisabetta Tedeschi, Razieh Nejati Fard

Deep-sea mining is in the future perspective of mining industry and it is currently in the technological development phase. The focus of this study is on the electrical power system that provides sufficient energy for the mining equipment at the seafloor, excavating Seafloor Massive Sulfide (SMS) deposits. SMS deposits usually exist at water depths between 1500 m and 4000 m. Despite the similarities of SMS deposits excavation to the open-pit terrestrial mines, more energy is required to drill and crush the ores in the hyperbaric conditions [1], which can be done whether by static trench cutters [1] or by mobile mining crawlers [2]. In addition, the ores vertical transportation by subsea pumps requires several MW electrical power that can be supplied by all-electric subsea motors or hydraulically from water injection motors located on the surface. The power requirements can be fulfilled by an offshore or subsea power network. As the SMS mines are usually in remote locations, the straightforward solution will be an isolated offshore grid mounted on a vessel or platform similar to the most of offshore Oil & Gas projects. These power systems resemble the onshore microgrids for industrial purposes operating in island mode. However, in contrast with the onshore power networks, there are space and weight limitations in offshore infrastructures, which impose the design compactness to be a priority. In addition, having a very high reliability is necessary in the design approach of the offshore projects due to the extraordinary high expenses corresponding to repair and maintenance. The other design criterion is to improve the power system efficiency in order to reduce the size of the power equipment cooling apparatus, operational costs and CO2 emissions produced by diesel/LNG onboard generators. There are a few studies considering power system distribution for seafloor mining industry. Among them, [3] has investigated the AC and DC alternatives for SMS mining in 2400 m water depth by considering Solwara 1 project scenario introduced by Nautilus Minerals Inc. [2]. In this study, a power system design tool will be presented taking into account various water depth, power consumption levels, different distribution configurations (AC and DC) and the aforementioned design criteria.

Jan 1, 2018

By Harald Brekke

On 13 July 2000, the ISA adopted the Regulations on Prospecting and Exploration for Polymetallic Nodules in the Area. The first contracts for such exploration were issued by the ISA the same year. The duration of exploration contracts is 15 years, after which the contractors are expected to go into exploitation. In 2013, ISA with the LTC initiated the process for developing the regulations for exploitation, and are currently working on the first draft to put forward for the Council. In the meantime, the first seven exploration contracts have expired, and been given five years extensions in order for the contractors to get ready to apply for exploitation contracts. According to the current draft of the exploitation regulations, an application for an exploitation contract shall be accompanied by all data acquired during the exploration phase, a mining plan, a financing plan, and a set of environmental plans (i.e. an environmental impact statement, an emergency response and contingency plan, environmental management and monitoring plan, and a closure plan). All of these plans have to be based on substantial scientific and technical data and information. The mining plan requires geoscientific data regarding the mineralogy and grade of the nodules, and the physiography of the mining site as a basis for the consideration of critical aspects, inter alia for making reliable resource estimations, design the mining operations, and forecast revenues. The environmental plans require the input of a substantial set of bioscientific data and information on the exploitation technology in order to establish base-lines, and monitor and evaluate the effects of the mining operations. Under the exploration contracts, such scientific data have been acquired and reported on an annual basis to the ISA. Some testing of mining equipment and experiments on the extraction of metals have also been performed by some contractors. These scientific and technical data from the exploration phase will be the basis for the for the preparation of the studies, plans and documents required for the applications for exploitation. No time frame is specified for the preparations of an application but it must be assumed to take place before the expiration of the exploration contract.

Jan 1, 2018

By Chuanshun Li, Haitao Zhang, Xuefa Shi, Quanshu Yan, Zhiwei Zhu

In Expeditions 22 and 26 of China Ocean Survey (COS), Chinese and Russian scientists have Carried out a lot of work to search for hydrothermal sulfide in Southern Mid-Atlantic ridge (SMAR) 19°S, but come back empty-handed at last. The sulfide formation is closely related with the water-rock reactions which are controlled by the heat source. Melt inclusions are considered to have a unique compositions in melt to reflect the deep magma processes. Fortunately, we have found a large number of plagioclase hosted melt inclusions in SMAR19°S MORB. We have done experiments by re-homogenization and re-crystallization of these melt inclusions. During the re-homogenization experiments, the forming and melting processes of the olivine crystal inside the melt inclusions indicate that the homogeneous temperature of melt inclusions is 1190-1200??. During the recrystallization experiments, the different mineral phase assemblages show H2O inside the melt inclusions has hardly ever been loss, in addition Cr element and H2O molecule in SMAR19°S magma are heterogeneity at the time of melt inclusions trapping, and then the re-crystallization experiments provide a method to prove the microheterogeneity of basaltic magma system. Combining with the bulk rock data, this study shows that the melt inclusions are formed at a low-temperature and high-pressure condition. Eventually, this paper speculates that a low temperature heat source generated by a lower mantle potential temperature or/and a thick lithosphere indicated by the melt inclusions that not experienced the H2O loss process are beneath the SMAR19°S. The low temperature heat source transmits its heat to lithosphere through the cooling thermal boundary layer (CTBL), and the thick lithosphere can sufficiently absorb and consume the heat. Under the interaction between the heat source and lithosphere, the residue heat at the infiltration depth of sea water might have been no ability to satisfy the water-rock reactions temperature, therefore, the water-rock reaction should hardly ever appear, so the theoretical reaction zone would not exist beneath the SMAR19°S. Eventually, the interaction between thick lithosphere and the low-temperature heat source should be the dominant factor that makes SMAR19°S area have no condition to form the seafloor sulfide. However, this paper is based on melt inclusions only, in fact, melt inclusions are potential to have melt compositions produced by mineral dissolution, reaction and assimilation, and the volumes of melt inclusions are exceedingly small compared to the overall size of the magmatic systems, therefore, the extrapolation across many orders of magnitude is implicit when applying petrologic information obtained from inclusions to entire magmatic systems. Therefore, there should have other more research to verify the reliability of this conclusion.

Jan 1, 2017

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By S. C. W. de Jong, E. de Hoog, J. M. van Wijk, S. J. Dasselaar

Introduction Technology development for sustainable, safe, reliable and efficient mining of polymetallic nodules in the deep seas requires careful design, thorough understanding and integrated testing of all equipment, physical processes and (sub) systems involved (Dasselaar et al [1]). Proceeding from Vertical Transport System (VTS) experiments at IHC laboratory scale by Van Wijk [2], with typical system dimensions of several meters, to prototype or pilot scale testing with typical dimensions of several kilometers, is a giant leap. Naturally, intermediate steps are required in order to mitigate the possible risks in the full-scale system’s (physical) processes. Within the EU program Blue Mining (2014-2018), possibilities emerged for performing experiments at intermediate scale: the so-called medium-scale vertical slurry experiments. Near Freiberg, Germany, the village Halsbrücke possesses a 140 meter deep empty vertical mine shaft, perfectly suited for housing the test setup. For this purpose, a 318 meter long 145 mm pipeline circuit was constructed, including both a 130 meter high vertical riser and fall pipe section. A purpose-built sediment injection and separation system was deployed, including a 55 kW centrifugal pump. The riser section has been equipped with sensors capturing pressure, temperature, flow velocity, volumetric concentration and flow visualization. The planning, modification and construction of the test facility site itself is described by Müller et al [3]. The present paper describes the objectives, experimental program, equipment, and the preliminary results. Publications on in-depth results are foreseen in the (near) future.

Jan 1, 2018

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By Ning Yang, Sup Hong

INTRODUCTION Metal components contained in deep-seabed mineral resources are being highlighted as “energy metals”, which are widely utilized in the entire fields of energy: harvesting and generation, storage and transportation, and saving. Those are mostly trace and rare metals, and rare earth elements as well: manganese, nickel, cobalt, copper, molybdenum, tellurium, selenium, platinum, etc. Toward low carbon society, for global sustainability, the role of metals and minerals is growing up in industries of energy and transportation [1]. In this context, the production and supply of energy metals from deep seafloor have to be approached also based on sustainable development. In deep-seabed mining activity, the sustainability is focused on potential impacts on ecosystems in benthic area and water column. The environmental impacts in deep-seabed mining are caused basically by intervention in benthic zones and transportation of materials. Those are, in particular, removal of benthic habitats, generation and dispersion of sediment plumes, surface transportation of seawater and sediment, tailing from mining vessel, sound and light noises, and chemical leakage, etc. This paper is aiming at fundamental guidance towards sustainable mining of polymetallic nodules.

Jan 1, 2018