Search Documents

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn). As result of chemical analysis of Mn, Cu, Ni and Co, polymetallic nodules observed in part of the EEZ of Mexico are possible of potential economic interest (Rosales and Carranza, 1990, 2001; Carranza and Rosales, 2003).

Sep 14, 2011

By D. S. Cronan

Pitcairn Island, the last remaining British Colony in the Pacific Ocean, falls in the S.E. Pacific. Its location, on top of a hotspot volcano, suggests the presence of submarine hydrothermal deposits in its EEZ. Such environments are known to contain hydrothermal mineral deposits, as in the case of Loihi submarine volcano near Hawaii, and Macdonald and Teahitia-Mehitia seamounts in the South Pacific. The hydrothermal deposits in these areas are formed as a result of the interaction of seawater with hot volcanic rock, producing a hydrothermal fractionation sequence comprising sulphides of Fe, Cu and Zn, oxides and silicates of Fe and oxides of Mn. In 1988, a GLORIA survey from the RRS Charles Darwin confirmed the existence of recent volcanism within the Pitcairn Island EEZ. A later bathymetric and sampling survey by the FS Sonne of the region round Pitcaim Island revealed submarine volcanoes approximately 80 km ESE of the island. Hydrothermal mineral deposits were recovered from them, and comprise finely laminated crusts of Fe oxides containing up to 50% Fe, and laminated hydrothermal Mn crusts up to 5 cm thick. Both morphologically and chemically the latter are similar to those from mid-ocean ridge and island arc settings, containing up to 50% Mn, associated with sulphides, and represent first discovery of such deposits associated with mid-plate "hotspot" volcanoes. Massive sulphide deposits are thought to occur within the volcanic pile.

Jan 1, 1992

By Raymond A. Binns

Exploration for undersea polymetallic sulfide mineral resources with high economic potential would be more effective given an ability to predict sites with particularly high gold contents (averaging say > 10 ppm Au). Herzig et al (1993) addressed this issue shortly after recognition that deposits in the back-arc Lau Basin (average 3.8 ppm Au) were enriched in gold relative to mid-ocean ridge sites (average 1.2 ppm Au). Small but significant numbers of hydrothermal sites with massive sulfide deposits averaging >10 ppm Au have since been discovered. The principal genetic factors underlying gold enrichment include depositional processes at and below the seabed, and the source of gold. It is timely to consider whether resolution of their relative importance can be translated into practical criteria for exploration strategies focused on especially gold-rich deposits. Comparing the ?grade? of seafloor deposits using analyses cited in research papers is fraught with difficulty, but there is no alternative at present to assuming that such averages provide an initial tenor guide. On this basis, four known polymetallic hydrothermal sites from convergent plate margins fit the exceptional-gold category with >10 ppm ?average? Au, while one from a divergent margin comes close: Sunrise (Myojin Knolls; 20 ppm ?average? Au) and Suiyo Seamount (28 ppm Au) in the Izu-Bonin Arc are frontal arc volcanoes dominated by rhyolite and dacite respectively, contrasting with more common mafic neighbor edifices (Iizasa et al., 1999). In both cases gold-rich massive sulfides occur in summit calderas with significant development of pumiceous volcaniclastic rocks, at depths around 1300 and 1370 m respectively. In the Eastern Manus Basin, PACMANUS (~1700 m; 14 ppm Au) and Suzette (~1550 m; 22 ppm Au) occur along the crests of volcanic ridges dominated by dacite/rhyodacite and andesite/mafic dacite respectively (Binns, 2004). Caldera structures are lacking. Although the Eastern Manus Basin is tectonically a rifted back-arc, its submarine volcanic edifices (picritic basalt to rhyodacite) have distinctly arc-style geochemical and isotopic affinities, differing from more typical back-arc basin basalts at the spreading axis further west (central Manus Basin). Probably as a consequence of transpression and a marked rupture in the New Britain subduction zone, submarine arc volcanism has here extended into the rifted back-arc region.

Jan 1, 2005

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By Hunsoo Choi, Sung Rock Lee, Ian J. Graham, Ian C. Wright

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese modules in the Campbell Nodule Field, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. The petrography, chemistry, inferred genesis, and 10Be/9Be dating of the nodules were described in the science report of GNS (Chang et al., 2003a, 2003b; Graham et al., 2003a) and presented at UMI (Chang et al., 2003c; Graham et al., 2003b). The morphology and distribution of ferromanganese nodules were also published in detail (Wright et al., 2005). This presentation is only concentrated on the mineralogy and chemistry of the nodules.

Aug 24, 2006

By Wilfred Lus

Meaningful and real time environmental monitoring of marine tailings placement is a clear sign of deeper commitment to the people of PNG in regard to impacts of mining on coastal environment and marine life. Today daily mine wastes and tailings are increasingly being delivered to the seabed offshore of project sites in Misima and Lihir islands. Ramu and Simberi mining projects also plan to dispose tailings out at deep sea. As tailings leave the tailings pipe and come out into the seabed, concentrations of the cations and other potential harmful particles in the tailings stream need to be quantifiably monitored each day during the life of the refinery. For continuous monitoring of the tailing?s true chemical characteristics submarine cables connected with ocean floor observation systems consisting of deep-sea underwater video, and cation sensors and electrodes will be laid. Power transport to the tailings site and data transfer from the tailings site will be via opto-electric cables. Various data center instruments will record and manage the collected data. Observation data will be transferred in real time to stake holder?s data centers via a dedicated line from on-land stations, and then distributed to company offices and government establishments. Japan Marine Science and Technology Center, Telikom PNG, and Australian Institute of Marine Sciences will be the key advisers in this project. The main role of the observatories is to monitor and collect background seabed geochemical data prior to start of tailings disposal, during tailings disposal period, and after the life of the refinery.

Jan 1, 2001

By Doug Lockhart

The Marine Minerals Technology Center has taken advantage of recent price and performance .improvements in PC hardware and software to upgrade its seismic acquisition system. In the past, single channel, high resolution, seismic data was displayed on an analog plotter and stored on tape. Associated navigation data was logged by hand or on a chart plotter. The navigation and seismic data were synchronized with time so that they could be cross referenced. The Center's new system uses PC's for the acquisition of both seismic and navigation data. Off the shelf software products were purchased for each task. Elics Delphl performs the seismic acquisition and processing, and GeoResearch, Inc. Geolink provides the navigation interface. A navigation string is sent from the navigation PC to the seismic PC via an RS232 line. This string consists of a time and location fix, as well as speed and heading data. The navigation string is then imbedded in the header of the seismic record. The Geolink software is capable of monitoring other devices in addition to the GPS used for positioning. Device inputs are attributed to the location data to provide easy construction of a navigation GIs. Currently the Center is logging fathometer data along with the navigation. As a result, a map of bathymetry along the tracklines can be available shortly after completion of the cruise.

Jan 1, 1992

By M. C. I. Modenesi, J. E. Smith, M. Salvá-Ramírez, G. M. Castro, J. C. Santamarina

Annual metal consumption per capita has increased several orders of magnitude worldwide since the turn of the 19th century, yet grades of terrestrial ores are decreasing as reserves dwindle. Consequently, deep sea metal deposits are gradually transitioning from identified resources to economically viable reserves. Deposits in the Red Sea deeps along the axial trough result from tectonic and local hydrothermal processes. Continental rifting and ocean floor spreading produce fresh oceanic crust; concurrently, seafloor evaporites flow into the spreading zone and form isolated deeps. The deeps are often filled with hot stratified brines maintained by locally discharged fluids during hydrothermal circulation. Metalliferous sediments precipitate from the brines within the deeps. The ongoing multipronged study at KAUST involves: (1) acoustic characterization of the metalliferous accumulations using advanced signal processing techniques that capture the physics of granular materials; (2) comprehensive mineralogical and textural characterization of sampled sediments using SEM, EDS, XRD, XRF, and ICP-OES; (3) multiphysics instruments deployed to measure undisturbed sediment properties in-situ; (4) development of a distributed seafloor observatory for monitoring field operations; (5) innovative concentration and separation technologies; and (6) new strategies for proper tailings disposal purposely conceived for the unique field conditions in the Red Sea deeps.

Jan 1, 2018

By Huaiyang Zhou

It has been long known that manganese nodules occur more or less in some part of marginal seas in West Pacific Ocean. On the other hand, it is difficult to understand their distribution and the genesis as those nodule samples were collected mostly by dredge from the deep basins generally has much higher sedimentation rate than the open ocean. For example, the sedimentation rate in the South China Sea is about three orders of magnitudes than that in region of the Clarion-Clipperton Fracture Zone. In June of 2013, a small seamount (named as Jiaolong Seamount), consisting of southern part and northern part with a distance of about 3 km each other, was visited by DSV Jiaolong/RV XiangYangHong 9. It is discovered that abundant manganese nodules exist only on the surface sediment in the southern part with a water depth of about 3800 m to 3300m, on the platforms nearby an obvious crater where volcanic rocks exposed on the wall. There are no any nodules be observed on the sediment in the northern part of the seamount (about 100 m deeper than the southern part) and surrounding deep basin (approximately 4000 m in water depth). It is speculated that a source of core for manganese nodule and a dynamic sedimentation environment, are two major governors for the growth and distribution of manganese nodule in the marginal seas.

Sep 14, 2011

By Kokichi Iizasa

Two major Kuroko-type deposits and minor sulfide deposits have been found in the middle Izu-Ogasawara (Bonin) Arc, Japan (Fig. 1). The Hakurei deposit, one of the major Kuroko-type deposits, was recently found in Bayonnaise knoll caldera in the nascent rift zone, which lies 20 km westward of the Sunrise deposit in Myojin knoll caldera on the Izu-Ogasawara volcanic front. The Hakurei deposit is a huge hydrothermal field measuring 500 m by 700 m in plan view. The Bayonnaise knoll caldera is mainly composed of dacite lavas and fragmental material on the caldera wall and rim, and its floor contains sediment composed of pumice, volcanic fragments, and hydrothermal clay. It is associated with a post-caldera dome and has a slightly ellipsoidal caldera rim that measures 3 km by 2.5 km, with about 200 m relief. The water depths of the caldera floor range from about 840 m to 920 m. The Kuroko-type deposit in the Bayonnaise knoll caldera occurs on the southeastern caldera floor where the caldera boundary faults intersect with a N-S-trending normal fault of the rift zone. In the deposit, many sulfide chimneys are generally less than 10 m high, and sulfide mounds are distributed around the caldera floor and on the sloping talus at the foot of the caldera wall. The deposit is buried in part by talus composed of pumice and volcanic fragments. Sulfide chimneys are still active, and inactive ones and their fragments are partly oxidized to reddish material. Chimney sulfides are mainly composed of sphalerite associated with chalcopyrite, galena, pyrite, and barite, and chemically enriched in Au up to 14 ppm and Ag up to 1400 ppm with major Zn, moderate Ba, and minor Pb, Hg, Cu, and Fe.

Jan 1, 2005

By Jai-Woon Moon

Lemkein seamount located in the west of the Kuwajleen Atoll of RMI is a relatively samll, simple-shaped, peaked type seamount with its base at 4,500 m and summit at 1,452 m water depths. Ferromanganese crusts were identified in the water depth range between 2,000 m and 2,500 m, and they were mostly observed on the northern slopes of the seamount. Among various substrate rocks, breccia occurred most commonly with crusts and formed the thickest crust layers. Average thickness of the Lemkein crusts was about 5 cm. Their chemical compositions were similar to other crusts found in the RMI area; Mn=25.82%, Fe=15.29%, Co=0.74%, Ni=0.56%. Lemkein crusts were characterized by their four distinctive internal layers; 1) Massive Layer 1; 2)Porous, Fe-stained or sediment infilled Layer 2; 3) Massive to slightly porous Layer 3; and, 4)Massive, Dense, Phosphotized, CFA veined Layer 4. Layers 1 and 2 were generally similar in composition, but highest Co concentrations were measured in Layer 1 while relatively higher concentrations of Al, Rb, Fe, and Ti were observed in Layer 2. Layer 3 showed higher concentrations of Ca and P than Layers 1 and 2. Based on the Co-chronography, the age of Layer 1 is 0¡?6 Ma (growth rate = 1.50 mm/Ma), Layer 2 is 6¡?15 Ma (1.75 mm/Ma), Layer 3 is 15¡?27Ma (1.76 mm/Ma), and Layer 4 is 27¡?45 Ma (2.06 mm/Ma). These preliminary results indicated that high Co contents in Layer 1 resulted from slow growth rates; Layer 2 was formed under relatively strong influence of high terrestrial input; and, Layer 3 was probably affected by a minor phosphatization event occurring in 15 Ma.

Jan 1, 2000

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn).

Jan 1, 2011

By Marlene Olivares Cruz

The particles that make up the deep-sea sediments have two main sources: 1) those that are created in situ from dissolved components and 2) those that are washed into the ocean in solid phases from the continents, atmosphere, space and interior of the Earth. Many particles as they sink through the water column reaches the seabed and are known as pelagic sediments with terrigenous, biogenic, authigenic, and cosmogenic components. Among the minerals found in the terrigenous fraction of pelagic sediments are quartz, clay minerals, feldspar, micas, ferromagnesians, and the biogenic fraction with remains of siliceous organisms, such as, radiolarian and diatoms. The chemical nature of marine sediments is controlled by the contribution of particulate matter derived from various sources with varying compositions for the fixing of elements during deposition and the compositional changes carried out within the sediments during diagenesis. In the last decade there have been several studies on the mineralogical composition of seabed sediments, suspended particulate materials and cores, together with paleontological and geochemical data are used for paleoclimatic and paleoenvironmental reconstructions, analyze changes in sea level, stratigraphic correlations and identify past and present sources of sediment and terrigenous input pathways and to describe the current ocean mass (Martins et al., 2001, Oliveira et al., 1998). There is also a scientific and economic interest in the authigenic fraction of pelagic sediments formed from other materials for polymetallic nodules. The study of sediments associated with polymetallic nodules helps to know the genesis, evolution and occurrence of these deposits (De Koven et al., 2003, Dubinin et al., 2008).

Jan 1, 2011

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By Jerry Hanua Naime

Papua New Guinea has permitted its first underwater mine. Nautilus Minerals (PNG) Limited is the company permitted to operate the Solwara 1 project. The project is located 30km off the nearest island of New Ireland in the Bismarck Sea. The successful permitting of the activity was due to the existence of a broad legislative framework and the collaborative efforts of stakeholders. Challenges faced included the lack of specific guidelines or policies for underwater mining; lack of existing technology and/or mining method; lack of benefit sharing mechanism for such a project and management of the perceptions of local communities that fear environmental degradation by the mining project. This presentation shares the experience of Papua New Guinea?s first under water mine. A background of the country, the project and the legislative framework are presented. Followed by the challenges and approach taken to permit the project.

Jan 1, 2010

By D. S. Cronan

Studies on polymetallic manganese nodules and Co-rich crusts in the EEZ's of the Cook, Line, Ellice and Phoenix Islands between 0-20°S show that Ni and Cu reach their greatest combined abundances of over 2% between 2-8°S on the southern margin of the equatorial zone of high biological productivity, as a result of biological fluxing of Ni and Cu to the nodules at and just below the CCD. By contrast, Co reaches it greatest abundance of 0.6% south of 8°S in nodules on non-biogenic clays well below the CCD where little biological Co supply is likely. Nodule abundances are greatest (up to 30kg/m2) in the Co-rich area in part due to AABW flow, giving highest overall metal quantities per sq meter in the nodules there, particularly of Co. There are approximately 110 x 106 tonnnes of combined Ni plus Cu plus Co expressed as Ni equivalent in Cook Islands EEZ nodules, approximately 12 x 106t. in Phoenix Islands ones, and approximately 1.4 x 106 t. in Ellice Islands ones, in areas of greater than 5kg/m2 nodule abundance. In the Co-rich crusts, Co averages about 0.7% and crust thickness about 1.6cm, both related to metal fluxes in and adjacent to the 02 minimum zone in association with which both maximum thicknesses and Co grades occur. Within the Cook Islands permissive area there are about 930 x 103 t. of Co and 630 x 103 t. of Ni in crusts, in Phoenix Islands crusts there are about 69 x 103 t. of Co and 55 x 103 t. of Ni, and in Ellice Islands crusts there are about

Jan 1, 1989

By Anthony T. Jones

Deep seabed mining requires technology to collect materials and transport them to the surface. An international patent search was conducted to define the state of the art in seabed mining technology. Over 350 patents were identified from 12 patent systems. The majority was from the United States, Japan, and the former USSR. Patent activity in this field peaked in 1983 when 34 patents were issued. Since 1984, on average 6 patents have been issued annually. The technology represents ten major classifications. With the exception of Deepsea Ventures, Kawasaki and International Nickel, it appears that much of the technology developed and tested in the 1970s by consortia active in seabed mining was never patented. Over the past two decades, identifiable trends in marine technology could influence seabed mining application such as more sophisticated communication systems, advances in hydraulic manipulators, improved computational technology in navigation, modeling of vessel ? ocean interactions, and improved materials. The most significant recent activity has been in European applications, which disclose remotely controlled subsea vehicles for mining diamonds.

Jan 1, 2001