Search Documents

By Kaihui Yang

Volcanogenic massive sulfide deposits are generally considered to have been formed by hydrothermal fluids that leach ore metals out of footwall rocks. However, the necessity for a metal-rich magmatic component in the ore-forming fluid of "giant" ore deposits has been debated over the decades. The solution to this issue is important not only for metallogenic models but also for the mineral exploration. In the hydrothermal leaching model, massive sulfides at mid-ocean ridges are deposited from hydrothermal fluids containing 80 ppm Fe, 6 ppm Zn, 2 ppm Cu, 350oC, and 0.7 g/cm3 density (average data for 21oN East Pacific Rise). A simple calculation demonstrates that such a dilute fluid is unlikely to have been responsible for the formation of the largest ancient massive sulfide ores of greater than 100x106 tonnes, such as Kidd Creek, Brunswick No. 12, Neves Corvo, and Rio Tinto. For such a deposit consisting primarily of pyrite, sphalerite, galena and chalcopyrite (other minerals, including gangue, might account for an additional 10-20%) and even assuming 100% precipitation and retention of the sulfides, more than 790 km3 of vent fluid would be required. For typical water-rock reaction ratios of about 2, this fluid would have to have reacted with about 395 km3 of rock to acquire its metals by conventional leaching processes. This estimate, however, conflicts with the observation that even a giant massive sulfide ore body is usually underlain only by a few cube kilometers of obviously altered rocks. Moreover, this model is not consistent with the observation of hanging wall alteration in many large massive sulfide deposits. The close spatial association between massive sulfides and volcanic rocks, in both ancient and modern sea floors, suggests that direct magmatic contribution should be taken into account in the genetic model. Magmatic fluids, capable of carrying abundant ore metals and volatiles and escaping from magma by depressurization, are well known from modern active volcanoes on land. High concentrations of metals occur in CO2-rich magmatic fluid trapped in felsic volcanic rocks nearby large presently-forming VMS deposits in the eastern Manus Basin (Pacmanus, Suzette) and also in the footwall rocks of Ordovician giant Brunswick #12 deposit in the Bathurst district, New Brunswick. Only 1% of such metal-rich magmatic fluid mixed with heated sea water, that has leached its metals from rocks, would contribute 85% of the total metals to form an orebody. Such magmatic fluids are most likely to be formed from volatile-rich felsic magmas that are prevalent in back arcs, and, if added to the normal circulation system, the fluids could be responsible for the formation of "giant" ore deposits. If this is true, then the study of magmatic fluids in the seafloor volcanic rocks may provide criteria for the exploration of large ore deposits.

Jan 1, 2011

By Thomas Pichler

In the past marine mining technology has focused on bulk mining of base metals from polymetallic massive sulfides. This has not been very successful because of the relatively low unit value of these metals and other reasons such as water depth, etc.. The process of gold enrichment in hydrothermal deposits is controlled through five different factors: (1) nature and source of the solution, (2) source of the gold, (3) a mechanism for mobilizing and transporting, (4) a mechanism for deposition, and (5) a mechanism to preserve the deposit. Gold has been identified in marine polymetallic massive sulfides from various locations on the ocean floor (e.g., spreading centers, seamounts) with contents ranging up to 5 ppm Au. This is within the current range of 1.0 to 7.0 ppm gold content which classifies gold ores. The gold appears to have been derived during hydrothermal alteration of the oceanic crust. Until the present there has been little attention to the possibility of mining gold or other precious metals in the marine environment. However, the magnitude of hydrothermal alteration (seawater can penetrates to a depth of 5 km into the oceanic crust) and primary gold contents of the rocks in the pathway of the fluid indicates that major gold deposits must have formed on or in the ocean floor, but they have not been found. To find a big deposit might only take an exploration model exclusively designed for gold exploration on the ocean floor.

Jan 1, 1993

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011

By Jun Lu

Compared with land mineral resources investigation, as well known, it is more important for marine geologists to get image data (e.g. photographs, video tapes and various charts) because they are often hard to reach deep seabed directly. In the past years a plenty of image data which are in various forms have been accumulated. In contrast with both digital and character data managing the image data by using database is just unfolding and it will be a trend for marine mineral resources investigation. GIS (Geography Information System) offers another useful means of processing image data, especially geological data. GIS is characterized by processing vector data (e.g. point, line and polygon), but newer versions of GIS software package are also able to process raster data (e.g. photographs etc.). The present author made a presentation on marine mineral image database during 25th UMI, but that system runs under DOS environment and dealt with only mineralogy. Recently a new system which integrates Oracle image database with GIS (ArcView version 3.1) has been developed. This system runs under Windows NT environment. In the network environment Server/Client mode is adopted, and over 200 basic subdatabases (tables)are located on Server; operating interfaces are located on several clients so that several persons can operate the system simultaneously. The whole system involves five types of marine mineral resources: manganese nodules, cobalt-rich crusts, polymetallic sulfides, phosphorites and gas hydrates. The data of every type of marine mineral resources described above are distributed among five units and several blocks. The units and blocks are described below:

Jan 1, 2000

By Seung-Kyu Son

This study was investigated about physico-chemical parameter such as water temperature, salinity, inorganic nutrients and total organic carbon (TOC). CTD (Model: Sea-Bird 911 Plus) castings were carried out on two transects in the northeast equatorial Pacific Ocean. As a part of the Korea Deep-sea Environment Study (KODES), inorganic nutrients and TOC were determined at 41 stations located from 131° to 136°W along 10.5°N and from 17° to 5°N along 131.5°W (Fig. 1). We particularly chose KODES Long-term Monitoring Station (St. KOMO) to observe for the annually environmental baseline study in the contract area. [ ]

Jan 1, 2005

By Peter Halbach

Within the frame of the German-Indonesian cooperative Bandamin research project two short cruises (7 station days each) were carried out which led to the Flores-Banda basin located north of the active volcanic arc. This basin is part of a large island-arc subduction-collision system resulting from a complex plate tectonic situation in which three major plates collide with each other. The eastern part of the Sunda-Banda convergent margin also includes the transition from subduction of oceanic lithosphere to collision of the Australian continental crust with the arc. This transitional part is cut and displaced by various large obliquely striking fault systems. Thus, the south eastern and eastern arc segments represent geological conditions which are suitable for the development of hydrothermal convection and potential mineral precipitation. Our study area lies north of the transitional section between Flores and Wetar. We started with a high-resolution bathymetric mapping of 240 km2 in a region some 36 km north of the island of Lomblen. A small submarine neovolcanic ridge was discovered striking approximately NW-SE and consisting of several submarine volcanic structures. In the northwest of the study area, the active subaerial Komba Volcano (Batu Tara) marks the youngest continuation of the ridge system examined. From the ridge we collected fresh and hydrothermally altered volcanics with disseminated sulfides (pyrite, pyrrhotite, markasite, and chalcopyrite), together with ferrugenous gossans.

Jan 1, 2004

By Chan Min Yoo, Kiseong Hyeong, Inah Seo

INTRODUCTION One of the major concerns for deep seabed mining is its environmental impact, from the disturbance of benthic communities due to the mining activity to the disposal of mine tailings back to the ocean. Yet a significant amount of waste materials would be produced from the on-deck processing on the mining platform, all the materials that produced on the mining platform are to be shipped to the land unless the related regulation and guidelines are developed by IMO and ISA (ISA, 2018). Still, ecotoxicology data for the deep seabed minerals from case studies in deep-sea tailings disposal (DSTD) and submarine tailings disposal (STD) sites are lacking and all other related aspects are also largely unknown. This year, the Republic of Korea has started a research project for the more comprehensive understanding of chemical and physical properties of mine tailings from the on-deck processing and the possible environmental impacts on the marine organisms after its disposal. Based on the scientific data collected from this project, Korea would be able to make recommendations for the methods and technical standards for the deep seabed mining discharges. The subjects of this project are threefold: to understand the physical/chemical properties of the tailings, to model the dispersion of particulates after the disposal, and to assess its impact on the marine ecology. Laboratory Experiments Producing Mine Tailings First, the possible waste materials are produced by mimicking the collecting and dressing processes at sea. The polymetallic nodules (PN) would be mined by using a collector lifting the crushed nodules out of the bottom sediment, and the bottom water, accompanying sediment, and the fine nodule particles which are too small to be recovered would be discharged to the ocean and thus are considered as tailings (Schriever and Thiel, 2013). In the laboratory, PN is crushed into the fragments smaller than 2 cm, abraded in the water using the rock mill, and then sieved to obtain the fine particles to be disposed.

Jan 1, 2018

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By Brian D?Olier

Much of the aggregate that is being exploited at present from these areas is a ?relic? deposit. It was originally eroded from primary source rocks and transported to a depositional centre by processes that are now either greatly reduced in effectiveness or are largely absent at the present time. Following the retreat of the Devensian ice sheet, the subsequent rise of sealevel and the drowning of large areas of the continental shelf along with the lower reaches of many rivers, a fresh sequence of sediment sources, pathways and sinks now exist. Sediment is being eroded from several, pre-existing source areas and transported along different, well - defined pathways to a number of new depositional sinks. Some of the present, licenced, aggregate dredging areas lie close to these sources, pathways and sinks with the consequent dredging activity being perceived by some as interfering with the ?natural process? that links the offshore and the coastal / littoral zones. With this perception in mind, the principal, sources, pathways and sinks between Flamborough Head and Beachy Head will be highlighted and the relationship of dredging activity upon them, evaluated. It will be demonstrated that offshore dredging activity has no effect upon supplies of sediment to coastal beaches.

Jan 1, 2004

By Kira Mizell, James R. Hein

Ferromanganese (FeMn) crusts form by precipitation of iron and manganese oxides from seawater onto a rock substrate and are therefore considered hydrogenetic in origin. Diagenesis does occur however, through the process of phosphatization. During phosphatization, abundant dissolved phosphate in seawater replaces carbonate in the detrital fraction as well as directly precipitates within the FeMn matrix as carbonate fluorapatite (CFA). This process is likely accompanied by the partial dissolution or replacement of the oxide phases [1]. As a result of these diagenetic processes, trace elements adsorbed on the oxides are released and can either be depleted or enriched in the phosphatized FeMn crust layers. Pb, for example, has been shown in sequential leaching experiments to associate with the iron oxyhydroxide (FeOOH) phase in purely hydrogenetic layers, while >95% of Pb in phosphatized crust layers is found in the CFA fraction [2, 3]. However, previous sequential leaching studies analyzed bulk layers of phosphatized crusts and only a few crusts, from the Pacific Ocean. Here we present concentration data for Pb and other trace elements in the CFA fraction leached from thin stratigraphic intervals of the phosphatized portion of FeMn crusts from the Pacific and Atlantic oceans to confirm consistency of trace metal association with CFA both throughout the phosphatized section and in two ocean basins. The Pb and trace element concentration data from this study will also be compared with data from non-phosphatized crusts from the global ocean. We can then determine the effect of phosphatization on the concentration of Pb and other elements of greater economic interest in FeMn crusts, specifically whether there is overall enrichment, depletion, or possibly even phase transfer of each metal in the phosphatized layers.

Jan 1, 2018

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By Benoît Waquet

In a context of scarce mineral resources, coupled with an increasing global demand in metals due to the exponential growth of newly industrialized countries, the mining industry will inevitably have to deal with tomorrow?s resources: underwater deposits. Three types of offshore deposits are known to date: polymetallic nodules, cobalt-rich crusts and hydrothermal sulphides. The latter, regarding the political-economic context, is now considered most likely to be exploited in a near future. Operating a mine critically requires accurate knowledge on geotechnical properties of the ore. A question is thus to be asked: Is there a particular spatial organization of geotechnical properties in a hydrothermal sulfide mound? In the present study, geotechnical properties have been measured for 29 sulfide samples of known origin, completed by 14 measurements on Western Pacific specimens from Yamazaki et al. (1990) and Yamazaki and Park (2003). From these geotechnical data on 43 sulfide samples, we can provide some answers to this question above, crucial for future exploitation of underwater mines.

Jan 1, 2010

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By James R. Hein

Low- to intermediate-temperature, diffuse-flow hydrothermal fields and associated mineral precipitates have been found at many locations along oceanic spreading centers, back-arc basin spreading axes, and midplate hot-spots. However, this type of hydrothermal field has not been found in oceanic fracture zones until recently. We mapped and collected samples from an active hydrothermal field in the Blanco Fracture Zone (BFZ) located in the northeast Pacific. The BFZ connects the Gorda and Juan de Fuca spreading centers and is divided into east and west segments by Cascadia Depression, a small spreading center. Small pull-apart basins occur along both the east and west segments. A complex set of basins near the western end of the BFZ includes from east to west, Surveyor Depression, East Blanco Depression (EBD), and West Blanco Depression. The hydrothermal field described here is located in the EBD.

Jan 1, 2001

By Alexander Malahoff

Field observations and sampling of land-based and submarine hydrothermal and geothermal sites show a definite link between the geological setting, fluid geochemistry and specialized assemblages of microorganisms found at these settings. Three initial sites have been chosen as a basis for these studies. The first site is located on hydrothermal vents in pit craters on the submarine volcano Lo?ihi (Hawai?i) at a water depth of 1,300 meters. The second site is within the geothermally active vents, ponds and lakes of the Taupo Volcanic Zone of New Zealand. The third site extends along the chain of volcanically and hydrothermally active volcanoes of the Kermadec-Tonga arc and back-arc system. To focus our work in New Zealand, a geomicrobiology field and experimental center has been established in Wairakei, New Zealand, with the relevant genomics, proteomic and bioinformatics work being conducted at the University of Hawaii. As part of a partnership between the University of Hawai?i, the Institute of Geological & Nuclear Sciences (GNS) and Victoria University of Wellington, a new interdisciplinary graduate course in geomicrobiology will be taught at Victoria University beginning next year. Since mineral-microbial interactions have been occurring for the past few billion years and these interactions have led to where one generates the other, a metal-bacteria research program has been initiated at GNS using arsenic-gold and other metal-bacterial interaction processes as a research objective. In this research program, we have completed the full genome of a new species of marine bacterium Idiomarina loihiensis from the Lo?ihi hydrothermal vents and identified specialized microorganisms living in pH 0.3 geothermal vent waters of White Island, New Zealand. The multidisciplinary approach to study the process of accumulation of metals in the hydrothermal systems clearly shows the path of how bacterial-mineral interaction can precipitate metal deposits. These studies will lead to new avenues for biomining, bioremediation and the understanding of the origins of life.

Jan 1, 2004

By Fred C. Dobbs

To effectively manage the potential environmental impacts of deep-sea mining of manganese nodules, we need to know substantially more about the effects of sediment redeposition on abyssal communities and the time scales of recovery from such effects. As an initial step towards a predictive understanding of mining impacts on abyssal benthos, we are conducting a series of biological studies within the framework of the Benthic Impact Experiment (BIE). Mining operations will cause resuspension of sediments across extensive areas of the abyssal Pacific Ocean. The resultant plumes likely will produce redeposition layers, ranging from a few sediment grains in thickness to > 1 cm, over thousands of square kilometers of the seafloor. The impact of such redeposition on abyssal benthic communities is exceedingly difficult to predict. While there has been speculation that redeposition of 1 mm or less will exert deleterious effects, there has been very little testing, and the BIE will provide the first in situ test of redeposition impacts. In a series of cruises before and after controlled resedimentation, we are collecting biological samples to determine the undisturbed state of the ecosystem, the immediate effects of disturbance, and the time-course of recovery resulting from quantified levels of resedimentation.

Jan 1, 1992

By V. K. Banakar, R. P. Rajani, A. R. Chodankar

The Afanasiy-Nikitin Seamounts (ANS) in Eastern Equatorial Indian Ocean (Figure 1) are shown to be the exposed part of the presently buried 85°E Ridge system under the Bengal Fan sediment and were emplacement around 75-80 m.y. ago (Krishna, 2003). The first recovery of ferromanganese crusts from the ANS was made during 1994, and the samples (Figure 2) provided important clues on the evolution of this seamount (Banakar et al., 1997).

By Kiseong Hyeong

The Intertropical Convergence Zone (ITCZ), where the southeast and northeast trade winds converge, is the effective climatological barrier that separates the southern and northern hemispheres in terms of dust budget. Asian and N. American dusts dominate in the Pacific north of the ITCZ, while Central and S. American dust prevails south of the ITCZ. In order to understand the nature of latitudinal and depth-related variations of mineral composition in terms of position relative to the ITCZ, deep-sea core sediments were collected from 9°N to 17°N at a 2° intervals along the 131.5°W meridian and analyzed for mineral composition. The amount of illite in surface sediments decreases gradually from 65% at 17°N to 31% at 9°N. In contrast, smectite increases from 11% to 56% southward. The observed mineralogical variation toward the ITCZ is attributed to the increased supply of volcaniclastic material transported via the southeast trade winds from the Central and South America source regions. Smectite-illite transition, a phenomenon that the amount of smectite increases over illite, occurs at around 10°N, the northern margin of the ITCZ. This result indicates that the change in latitudinal position of the ITCZ in the geological past could be recorded by the smectite-illite transition in deep-sea cores. The cores studied show down-core variation of mineral composition from illite-rich at the surface to a smectite-rich clay suit at depths, similar to the latitudinal variation. The smectite-illite transitions observed in these cores are likely the records of changes in latitudinal position of the ITCZ. The depth and age of the smectite-illite transition is getting shallower and younger towards the equator, implying that the ITCZ was located farther north during late Tertiary and has shifted southward to the present position of 5°N~10°N.

Jan 1, 2004

By V. V. Ivanov, A. I. Khanchuk, E. V. Mikhailik, M. G. Blokhin, P. E. Mikhailik

At present, marine ferromanganese crusts of seamounts are of great interest as a source of high-tech metals. The metals most enriched in these deposits are essential for a wide variety of green-tech, emerging-tech, and energy applications (Hein et al., 2013). There is a grate number data on the content of major and minor metals (thousands analyses). However, information on the content of such elements as platinum, gold and silver in the world literature is limited. The concentrations (N – number of analyses) of platinum, gold and silver in the Pacific are 418 ppb (N = 105), 35 ppb (N = 72), 1.02 ppm (N = 26), respectively, and in the North Pacific Prime Zone - 477 ppb (N = 66), 55 ppb (N = 13), 0.1 ppm (N = 4); in the Atlantic Ocean is 567 ppb (N = 2), 6 ppb (N = 2), 0.20 ppm (N = 18), in the Indian Ocean, 211 ppb (N = 6), 21 ppb (N = 2), 0.37 ppm (N = 9) respectively; (Hein et al., 2013). The northern part of the Pacific is poorly studied in this question. The samples of ferromanganese deposits (FMD) was recovered from the Govorov Guyot (Magellan seamounts), MZh-33 Guyot (Marshall Islands), as well as the Detroit Guyot (Imperor Ridge) and Yomei Guyot (Fe-Mn placer Holes 431 and 431A DSDP, Imperor Ridge).

Jan 1, 2018

By R. C. Newell

The primary objective of this study was to establish the fate and distribution of material rejected during marine aggregate dredging, and the extent to which this is associated with spatial changes in biological community composition. Two actively dredged sites in the southern North Sea (Licence Areas 430 and 106) were selected in order to provide a comparison of impacts between sites subjected to different levels of dredging intensity and of contrasting environmental conditions. Dispersal of material rejected during the dredging process was monitored by means of acoustic doppler current profiling techniques (ADCP). Composition of the substratum and benthic invertebrate assemblages were investigated by the analysis of seabed grab samples. It was found that dredging in both areas had an impact on seabed bathymetry in the form of dredge furrows and also led to a reduction of the coarse gravel-sized components of the worked area. Sand sized particles were shown to increase in the surface deposits of both dredged areas. This is likely to reflect both the removal of coarse particles as cargo and the settlement of finer particles rejected during overboard screening. Dispersion and settlement profiles of material rejected by dredging vessels suggested that the majority of the suspended sediment load resulting from overboard screening settles to the seabed within 500 m. Some evidence of suspended sediment loads above background levels were noted at distances of up to 2 km from the working vessel. Analysis of the particle size composition of the deposits, along the axis of transport of material from the dredged sites, suggested that the impact on the sediment composition outside the boundaries of the dredged sites is dependent on the strength and direction of net sediment flux at the seabed. Benthic invertebrate communities within the dredged zones of both areas were found to differ significantly from communities in nearby undredged deposits. A major suppression of species richness and abundance was noted in the dredged sectors of both sites when compared to control locations. A ?footprint? of potential impact on the benthic fauna was noted in samples taken along the axis of sediment transport at distances of up to 1750m outside the boundaries of Area 430. In contrast, impacts on benthic community structure at Area 106 appeared to be confined to the immediate vicinity of the dredged zone itself. This apparent difference in impacts, beyond the boundaries of the dredged sectors between the two study sites, was thought to be a reflection of the smaller quantities of material rejected at Area 106 and the weak seabed sediment flux which is characteristic of this area. These findings, along with those of numerous dredging impacts studies, were then used to make generalised predictions of macrobenthic community recovery following marine aggregate extraction in a variety of seabed habitats.

Jan 1, 2004