Search Documents

By Charles L. Morgan

The Minerals Management Service of the U.S. Department of the Interior and the State of Hawaii Department of Planning and Economic Development are investigating the cobalt-rich ferromanganese oxide crust deposits found within the Exclusive Economic Zones (EEZ) of the Hawaiian Islands and Johnston Atoll. The objective of this investigation is to complete a preliminary resource assessment and an Environmental Impact Statement for potential leasing of mineral rights to these crusts. The results of this effort will be summarized and published in a Draft Environmental Impact Statement in March 1986. Three oceanographic cruises to deposit sites in the Hawaiian Islands EEZ were conducted by the University of Hawaii in 1984. As a result, data and sample analysis yielded the following resource estimates (in thousand tonnes): (1) total crusts - 378,500; (2) cobalt - 2,500; (3) manganese - 76,200; (4) iron - 59,700; and (5) nickel - 1,400. These estimates do not include key factors such as deposit continuity, recoverability, and environmental sensitivity. A preliminary attempt to quantify some of these factors for one particular deposit is in progress and will consist of detailed field studies followed by laboratory analysis. Similar evaluations of the Johnston Island EEZ have also begun and are based upon field work conducted by West German researchers and the U.S. Geological Survey. The Johnston Island EEZ appears to have crust resources about as large as those contained in the entire Hawaiian EEZ.

Jan 1, 1985

By Wiebe Boomsma

INTRODUCTION Starting in February 2014, 19 partners from EU industry, research institutions and academia joined forces and formed the Blue Mining consortium. In the following four years, they have set out to work on the development of deep sea mining technology, looking into exploration, identification, economic assessment and vertical transport systems for the mining of seafloor massive sulphides and polymetallic nodules. In the beginning 2018 this research & development project has come to an end. The Blue Mining project was one of the first EU subsidised projects embracing the TRL system. This system describes a method of de-risking technology using a simple 9-step approach. This method requires experimental testing in laboratory and relevant environments to be able to reach the higher levels (TRL>5) This paper will discuss the progress in development of the vertical transport system, with a focus on the performed experimental work. This paper will discuss three topics: • Booster station technology • Riser dynamics • Vertical hydraulic transport process. BOOSTER STATION TECHNOLOGY Deep knowledge of transport processes is a prerequisite for a clog free vertical transport One of the key technologies in the VTS is the booster station. The centrifugal pump booster station concept is developed in Blue Mining, it consists of two centrifugal pumps and multiple valves, assembled in member-type frame. Deep sea conditions pose special requirements on all components due to the extreme pressures at large water depths. In the Blue Mining project a Deep Sea Special Motor has been developed and tested in laboratory and in the field. The motor is completely filled, lubricated and cooled using seawater due to its unique open structure, furthermore it does not require any lubricants minimizing the environmental pressure of the motor. The motor is first extensively tested in a laboratory, after these tests have been concluded successfully, the motor is shipped to Norway where it has been successfully tested for more than 100 hours at 425 meter water depth.

Jan 1, 2018

By P. Halbach

Hydrothermal activity is well known from many locations on most mid-ocean ridges, but no hydrothermally mineralized area had yet been found at the ultraslow spreading southwest Indian Ridge up to October 98 when the Japanese RV Yokosuka with the submersible Shinkai 6500 investigated this area. A massive sulfide field was discovered near 27°51S / 63°56E in the 11th segment west of the Rodriguez Triple Junction. The Free University of Berlin had joined this cruise and taken over the responsibility for the study of the respective sulfide mineralizations. Hydrothermal minerals were sampled during two dives at a water depth of 2940 m close to the summit of an axial volcanic ridge called Mount Jourdanne. Massive sulfides occur on the seafloor as small smooth mounds with an average area of about 5 m2. Their surfaces are weathered and have a reddish to brownish colour. In addition to these mound-like structures, small tube-like chimneys were observed; these chimneys rise approximately 30 to 40 cm above the floor and are less than 10 cm in diameter. No indications of hydrothermal fauna could be detected. All the hydrothermal features are spatially related to faults and smaller fissures controlled by an E-W trending graben system crossing the summit region of the submarine volcano. Such tectonized areas are generally considered to be ideal for hydrothermal activity because they may have both a magmatic heat source in the deeper underground as well as pathways for the fluid circulation.

Jan 1, 2002

In the western Woodlark Basin, propagation of seafloor spreading is occurring directly into the continental crust of Papua new Guinea. The spreading is not strictly in a back-arc tectonic setting, rather it appears associated with microplate rotations related to the complex convergence of the Indo-Australian and Pacific plates in the southeastern Pacific region. Volcanic rocks along the western Woodlark spreading axis range from normal mid- ocean ridge basalts to basaltic andesites with back-arc geochemical affinities. Rare peralkaline rhyolites also occur. Hydrothermal deposits occur at a basaltic andesite volcano located on the neovolcanic zone near its westernmost propagating tip. Franklin Seamount is a 250m-high cone constructed largely of pillow lavas and talus which sits astride a 450m-high ridge of similar lavas oriented subnormal to the spreading direction. At its crest, 2150m below sea level, there is a 100m-deep caldera.

Jan 1, 1993

By Peter Halbach

Hydrothermal activity is well known from many locations on most mid-ocean ridges, however no hydrothermally mineralized area had yet been found at the ultraslow spreading southwest Indian Ridge up to October 98 when the Japanese RV Yokosuka with the submersible Shinkai 6500 investigated this area. A massive sulfide field was discovered near 27º51S / 63º56 E in the 11th segment west of the Rodriguez Triple Junction. The Free University of Berlin had joined this cruise and taken over the responsibility for the study of the respective sulfide mineralizations. Hydrothermal minerals were sampled during two dives at water depth of about 2940 m close to the summit of an axial volcanic ridge called Mount Jourdanne. There massive sulfides occur on the seafloor as small smooth mounds with an average area of about 5 m2. Their surfaces are weathered and have a reddish to brownish colour. In addition to these mound-like structures, small tube-like chimneys were observed. These chimneys rise approximately 30 to 40 cm above the floor and are less than 10 cm in diameter. No indications of hydrothermal fauna could be detected. All the hydrothermal features are spatially related to faults and smaller fissures controlled by an E-W trending graben system crossing the summit region of the submarine volcano. Such tectonized areas are generally considered to be ideal for hydrothermal activity because they may have both a magmatic heat source in the deeper underground and pathways for fluid circulation, respectively.

Jan 1, 2001

By Alexander Malahoff

The most exciting frontier in Ocean Technology is represented by a new class of Marine Bioproducts, the source of which lies in marine microorganisms. The microorganisms include microalgae, bacteria and archaea. These organisms represent very diverse, adaptive life forms and in their metabolic processes use carotenoids, polyunsaturated fatty acids, ultraviolet blockers, as well as a wide range of enzymes that are pivotal in the production of new pharmaceuticals and nutraceutical products. These organisms cover a wide spectrum of ocean environments, from the shallow to the deep, from the normal to the extreme. The technological challenge is in the identification of candidate organisms, in the screening for valuable enzymes, and in the industrial production. A whole new range of collecting strategies involving submersibles, ROVs and in situ ocean floor instrumentation is emerging. New non-polluting industrial chemical processes involving the use of photobioreactors and extremophile bioreactors for breeding and monitoring these organisms in neo-farming technology is emerging. The commercial value of these candidate products is immense, as is the range of potential organisms. The dimension of this new industry is global. The Marine Bioproducts Engineering Center (MarBEC), funded by the National Science Foundation (NSF), has been established at the University of Hawaii. The vision of MarBEC is to develop a seamless research system stretching from undergraduate education to industry for the purposes of producing valuable marine bioproducts outside of the normal chemical factory production. MarBEC is uniquely and strategically placed in the Pacific to explore, find, and adapt highly bioactive marine micro-organisms found in the tropical ocean. We have watched the increasing need by the ever-

Jan 1, 2000

By P. Mikhailik

Recently, characterized by fast development high- and nano-technology, demand for rare and trace metals has increased. One of such metals is gallium. Gallium compounds, mainly GaAs, are used in medicine, to manufacture optoelectronic devices, microwave techniques, devices of solar power and infrared optics, etc. The basic gallium industrial deposits are known only on land. There are bauxites (50 ppm), nepheline rocks and ores (36-38 ppm, minerals concentrators are nepheline and sodalite), Zn-Pb-Cu ores (5000-12000 ppm, minerals concentrators are gallite, germanite, sphalerite, bornite), sulphide-polymetallic and Pb-Zn ores (10-32 ppm, minerals concentrators sphalerite, chalcopyrite) (Vershkovskya et al., 1998). High concentration of gallium are observed in hydrothermal massive sulphides of a Mid-Okinawa Trough (The South Chinese Sea) and Sujo seamount (The Philippine Sea) (Noguchi et al., 2007). As it is known, deep-sea massive sulphides and associated Fe-Mn crusts are products of hydrothermal fluid discharge. High-temperature massive sulphides precipitation are the first, and low-temperature Fe-Mn crusts deposition is the last process of hydrothermal mineralization (Cronan, 1982). Hydrogenic crusts and nodules of the World ocean are characterized by low concentration of Ga, close to clarke (19 ppm) (Kobaltbogatye.., 2002). Hydrogenic crusts from the Sea of Okhotsk are exception, because Ga concentrations are exceeded clarke in 3,5 times (Mikhailik, et al., 2009). Complex studying of Fe-Mn crusts from deep-sea basins volcanic seamounts of the Sea of Japan has shown their hydrothermal-sedimentary genesis (Mikhailik, 2009). High gallium concentration (up to 850 ppm) was established in these crusts by ICP-MS (Agilent 7500C). Microprobe research (JXA-8100) of samples Fe-Mn crusts has not revealed the gallium minerals concentrators. It suggests that, gallium in Fe-Mn crusts of the Sea of Japan is sorb substance.

Jan 1, 2010

By Michael W. Milner

Cold Ocean Placers: Polar storms, interstadial littorals and crustal adjustments. Polar storms with consistent strong winds in the Southern, Antarctic Ocean are responsible for placer deposits on both the east and west coasts of Australia, on the west coast of New Zealand, as well as on the coasts of South America and Africa. Arctic winds, confined by both land and ice, generate similar placers in Labrador and Greenland as well as on the coasts of Scotland, Norway, Hudson's Bay, Nome, Goodnews Bay, Kamchatka and the north coast of Siberia. Tasman and Labrador seas have several parallels to Newfoundland, including north-south polar waterways, young spreading ocean floors, and youthful coastal escarpments with glaciated coasts. Black sand beds in beach deposits on the modern and Pleistocene transgression strandlines, skewed to the distal ends of beaches, and set into either bedrock or sediment fill, are the locus of the light-heavy mineral placers with titanium, zirconium and rare earth elements; chromium; iron; and tin. Gold and platinum group elements are the ultra heavy minerals at one end of the spectrum and tend occur in proximal placers generated, either directly from bedrock sources, or as minor by-products in distal light-heavy mineral placers. Diamonds are unusual in that the value is only in the larger stones, despite the formation of beach sand and aeolian placers in the littoral zone, and the sites of concentration are in very high energy bedrock traps, on terraces that are mined to depths of 100 metres below sealevel.

Jan 1, 1995

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45' and 41°05'N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01'N latitude are part of a chimneylike vent structure with a

Jan 1, 1988

By P. E. Halbach

On June 26, 1988, the Jade Hydrothermal Field was discovered in the Okinawa Trough by the German RV Sonne. This research cruise has taken place within the scope of a German-Japanese cooperative project. The Okinawa Trough, located between the Ryukyu Island Chain and the east coast of China, is an active backarc-basin formed by extension within the continental lithosphere. The Ryukyu arc consists of a nonvolcanic outer arc, forming the main island chain and representing compressive highs of the Asian continental margin, and an inner arc with present-day volcanism in its northern part (Sibuet et al. 1988). The valleys and ridges of the trough are cut across by transverse faults, giving rise to younger volcanic intrusions. The Jade Hydrothermal Field was detected in a caldera-like structure. It is. located at about 27°15,0'N and 127°04,5'E with a maxi- mum water depth of about 1650 m. Data of heat flow measurements show a high anomaly in the cauldron basin with values ranging from around 100 to 800 mw/m2 (Halbach et al. 1989). The hydrothermal vent area was discovered in the northern part of the inside northeast slope of the cauldron in a water depth between about 1300 and 1500 m. We identified different varieties of hydrothermal

Jan 1, 1989

By Jan M. Peter

Many of the Pb-Zn massive sulfide deposits of the Bathurst area in northern New Brunswick, Canada, are intimately associated with laterally continuous iron formation (IF) (Figure 1). This IF is a fossil laminated, exhalative, chemical sediment. Together, the IF and the Brunswick #12, Brunswick #6, and Austin Brook deposits (rightmost discontinuous horizon on Figure 1) are collectively referred to as the "Brunswick Belt". To date we have only studied the Brunswick Belt and have not examined the horizon along which the QSR, CNE and Flat Landing Brook deposits lie. The Bathurst area is underlain by the Tetagouche Group (Figure 2), a Cambro(?)-Ordovician sequence of metasedimentary and bimodal metavolcanic rocks that was intruded by mafic to felsic plutons and subsequently deformed during the Taconic Orogeny. The stratigraphic sequence consists of shales and greywackes that are overlain by carbonaceous shales and felsic volcanic and volcaniclastic rocks; these are in turn overlain by mafic volcanic and sedimentary rocks. The massive sulfide deposits and IF occur within the upper portions of the felsic volcanic rocks in close association with carbnaceous metasedimentary footwall rocks (Figure 2).

Jan 1, 1993

By Janine Lahr, Peter E. Halbach

The Manus Spreading Ridge is located within the EEZ of Papua New Guinea and lies in the Manus Basin ENE of the PNG Island and N of the Island New Britain. The divergent backarc spreading system is caused by the subduction of the Solomon plate in the South under the Bismarck plate in the North along the lineament of the New Britain trench. The rate of divergence is relatively high compared to other back arc spreading systems and amounts up to 12 cm/year [3]. Since submarine volcanism and associated hydrothermal circulation as important parts of the oceanic heat transfer system are also dependent on the rate of spreading, hydrothermal fluid venting and respective deposition of polymetallic sulfides can be expected there. In late 1985 first indications for hydrothermal activity were observed on a swell within the central rift valley of the Manus Spreading Centre during a photographic survey of the seafloor by an expedition of the Hawaii Institute of Geophysics with the American RV Moana Wave [1]. Detailed geological investigations including successful sampling were first carried out in June 1990 within the scope of the OLGA II research project (conducted by Prof. Tufar, Marburg) using the German RV Sonne equipped with a deep-sea television sledge and Tvcontrolled grab systems. Simultaneously a research cruise with the Russian RV Akademic Mstivlav Keldysh took place using the manned submersible Mir; the findings of the OLGA II cruise were immediately used for planning and organization of the Mir dives [3]. The massive sulphide samples which we used for our geochemical and mineralogical studies originate from the hydrothermal fields 1 and 2 and are from grab stations of the OLGA II expedition [4].

Sep 24, 2006

By Nobuyuki Okamoto

Ferromanganese crusts on the seamounts in the Pacific Ocean are potential resources of cobalt, nickel, platinum and REEs. Particularly, those of the Republic of Marshall Islands and the Federated States of Micronesia (FSM) waters are believed to be of the highest resources potential area in the Pacific Ocean. The total six cruises using the Japanese Research Vessel Hakurei Maru No. 2 were carried out in the seamounts of the Marshall Islands in 1996, 1998 and 2002, and of the FSM in the 1997, 1998 and 2005 for evaluation of economic potential for cobalt-rich ferromanganese crusts as part of the Japan-SOPAC joint project. During these cruises numerous data such as bathymetric, geological, geophysical and environmental data were obtained. Geophysical exploration with backscatter mapping and side scan sonar, visual imaging using towed TV camera and geological sampling using dredge bucket and/or benthic multi-coring system (BMS) were conducted on these seamounts. In this presentation, we will report the mode of distribution of the crusts and calculated resource estimation based on the results of these geological and geophysical shipboard survey and land-based analyses. Keywords: ferromanganese crusts, Marshall Islands, Micronesia, resource potential

Jan 1, 2011

Clark volcano is a large volcanic center on the active arc front of the intraoceanic Kermadec arc. It is one of the two southern-most Kermadec arc volcanoes (the other being Whakatane volcano) that sits on oceanic crust before the transition to continental New Zealand, and is underlain by the 17-km-thick Hikurangi Plateau, which is presently subducting beneath the southern section of the Kermadec arc. Unusual K-rich basaltic lavas have been recovered from Clark (1.5 to 2.25 wt.% K2O), together with more typical basaltic-andesite, andesite and dacite rocks. The total volume of the Clark volcanic center is ~90 km3, calculated from the summit of the volcano down to the 2,500 m contour (which marks the inflection point of the volcano flanks with the surrounding seafloor) and comprises two separate edifices similar in size; the northern one having a volume of ~4.57 km3 and the southern one 4.43 km3. The volcano has a maximum relief of ~1,645 m from the 2,500 m contour to the summit of the shallower northern edifice shoaling to 855 m below sea level. The northern edifice is comprised of twin peaks each consisting of a constructional cone, with evidence of sector collapse having occurred between the cones. A more recent, smaller cone again has grown on the eastern flank between these summit cones. Massive, blocky lavas and coarse talus dominate the summits of the cones, with finer-grained volcaniclastic material and sediments a feature of the volcano flanks. The southern edifice is noticeably more dissected than the northern one, having a pronounced horst in the centre of the volcano bounded by 5-6 km-long faults. There is no obvious constructional cone atop the southern volcanic edifice.

Jan 1, 2011

By William D. Siapno

Mining the deep ocean by the year 2000 may seem far fetched. The year 2000 is but a decade away, a scant 10 years. Remember, the youngsters of today will grow up in a little more than a decade and rebut the wisdom of the ages, especially the traditions of their elders. Rude perhaps, but none the less a fact of life. Ocean mining exhibits many of these same traits. We should all brace ourselves for some rude shifts in our rapidly moving society. Major shifts in economics, politics, and social orders are the rule of the day. Communism is in retreat, our own economic structures chaotic. So in this moment of cataclysmic change, a shift in the international market place of mineral resources should not be a great surprise.

Jan 1, 2011

An extensive ferromanganese nodule field south of New Zealand (Fig. 1) has existed beneath the flow of the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) for at least the past 15 m.y. West of 174°E, between 59°S and 48°S, the field is 300-500 km wide, but east of 174°E, where current flow impinges on the eastern slope of the Campbell Plateau, the field narrows from ca. 200 km at 55°S to ca. 120 km at 51°S. This narrowing coincides with deflection of current flow eastwards, and consequent reduction in bottom-current velocity and eddy kinetic energy. Based on sea floor photographs, dredge samples and 3.5 kHz profile data, six distinct seafloor substrates are delineated, forming broadly parallel zones eastwards from the lowermost Campbell Slope (Fig. 2).

Jan 1, 2003

By Alexander Malahoff

The summit of L_ihi submarine volcano changed dramatically after seismic activity beneath L_ihi during the month of August 1996. Bathymetric re-surveys of the L_ihi edifice using SeaBeam, Simrad and deep-towed Reson-Focus multibeam systems showed the presence of new north-south striking fissures, normal faults and a new pit crater located at the site of a former 300-meter high volcanic cone. Comparisons between the pre-1996 SeaBeam data and the new bathymetry show a net loss of about 100 million cubic meters of rock volume on the summit. This loss is localized at a new pit crater -- the 300-meter deep by 1,300-meter wide Pele's Pit. Submersible observations with Pisces V show the northern edge of Pele's Pit to be bounded by a normal fault located north of the site of the former Pele's Vents cone that has disappeared into the new pit crater. A new hydrothermal field, the Ikaika Vents, extending from a water depth of 1,311 meters to 1,287 meters has formed at the northeastern edge of the floor of Pele's Pit. Submersible observations of these new Ikaika Vents during September 1996 showed vigorous venting at the site with extensive white-colored bacterial mats hanging off the rock face above the vents. Follow-up mapping and sampling of the vent sites during August 1997 showed vent temperatures of up to 198°C, dense populations of vent shrimps around the vents and a centimeters-thick veneer of fine-grained polymetallic sulfide mineralization along the rock walls above individual vents. The mineralogy of the sulfides shows a barite, chalcopyrite, sphalerite, and pyrite composition.

Jan 1, 1998

By Darryl Thorburn

The Cook Islands are 15 islands located in the Southwest Pacific (between 8-23°S latitude and 156-167°W longitude). The total land area is about 200 km2. However, because its islands are widely scattered, the EEZ of the Cooks encompass an area about 2 million km2. The Cook Islands government exercises sovereignty and jurisdiction over its EEZ according to international law and convention as a member state under UNCLOS1. Accordingly, the Cook Islands government exercises full control over resources in its EEZ, including minerals on the seabed. Decision making on allocating licences for exploration and ultimate mineral recovery is by the Cook Islands government and will be set out in relevant statutes. Seabed minerals investigations within the EEZ of the Cook Islands and adjacent waters were first carried out by, USSR, US, and New Zealand research vessels in the late 1960 early 1970?s and indicated the presence of high concentrations of manganese nodules. This early work was followed by a number of Government funded surveys in and adjacent to the Cook Islands EEZ These surveys have identified a world class resource of manganese nodules within the Cook Islands EEZ (CI EEZ), containing significant

Sep 14, 2011

By Ki-Hyune Kim

The Korea Ocean Research and Development Institute conducted its first exploration for deepsea mineral resources in 1983, and began a systematic deepsea prospecting in 1989 among Micronesian islands and in central and eastern parts of Carion-Clipperton fracture zones of eastern Pacific. With the arrival of R/V Onnuri in 1992, KORDI commenced a full-scale national program for nodule exploration. The total area surveyed by KORDI covers more than 1,500,000 km2. At the end of 1993, based on the collected data, Korea designated 300,000 km2 in the Clarion-Clipperton fracture zone as prospective mining area for manganese nodules, and accordingly, the government of Korea submitted the application in January of 1994 to the United Nations for registration as a pioneer investor and for the allocation of a pioneer area. This application was approved by the General Committee of the Preparatory Commission in August 1994. As a result, Korea became the 7m pioneer investor under the United Nations Convention on the Law of the Sea. KORDI is now carrying out detailed exploration survey and environmental studies in the registered area to fulfill required obligations to UN, and Korea will continue exploring the last frontier on earth. It is KORDI's unshaken calling to be successful in exploiting deepsea resources to provide our nation resources it lacks. It is not only a challenge to explore deepsea, but it is also our national mission to explore and succeed in our endeavor for future generation.

Jan 1, 2011