Search Documents

By Yannick C. Beaudoin

Southern Explorer Ridge (SER) is an anomalously shallow, intermediate-rate spreading ridge located 200 kilometers off the west coast of Vancouver Island, Canada. It ranges in depth between 2600 m (deepest basins) and 1760 m (bathymetric minimum). At least 60 sulfide deposits are known to be associated with hydrothermal vent fields along the ridge. For the first time geological data, including deposit locations, collected from 15 marine expeditions to SER since 1983 have been assembled in a GIS format. GIS processing techniques were employed to plot the distribution of base metal concentrations for recovered sulfide samples. The highest base metal concentrations are found in the vicinity of the Magic Mountain site (main active vent field), and also proximal to a side scan sonar anomaly referred to as AGOR 171. Individual samples near these locations have yielded values as high as 29.3 wt\% Cu, 34.3 wt\% zinc, 0.97 wt\% Pb, 2.0 ppm gold, and 664 ppm silver. Sample paucity is the key limiting factor that prevents adequate assessment of the areas economic potential.

Jan 1, 2001

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991

By Glen Smith

Nautilus Minerals is the world leader in exploration and development of deep ocean seafloor massive sulphide (SMS) resources. The company is currently focused on generating its resource pipeline in the Western Pacific and its first development project for recovery of high-grade copper, gold and silver mineralisation from its Solwara 1 site in the Bismarck Sea, Papua New Guinea. The Solwara 1 site is located at a water depth of 1,600 ? 1,800 meters. Over 150 SMS seafloor surface samples have been collected from chimney structures during dives made by remote operated vehicles (ROVs). In order to obtain an understanding of the sub-surface mineralisation, Nautilus carried out 4 drilling programs between 2006 and 2010 which allowed the calculation of a Canadian NI43-101 compliant resource estimate. The initial 2006 campaign was based on conventional offshore surface driven drill equipment. In conjunction with the subsea remote technology industry, Nautilus subsequently developed an ROV operated seafloor drill system with improved drill core recovery and efficiency. This technology was developed further with a 2010 - 2011 drill program to increase the available geological knowledge at Solwara 1 and adjacent prospects. his paper will provide an overview of Nautilus? SMS drilling requirements and recap the evolution of drilling technology and operations undertaken at Solwara 1 from 2006 to 2011. The paper will also discuss the potential of further developments in drilling techniques and equipment to increase or improve drilling depth, efficiency and data quality.

Jan 1, 2011

By Ivo Dreiseitl

The interaction between nodule harvester and eupelagic sediment on the seabed is definitely one of the key aspects of mining technology for polymetallic nodules which is to be studied in details. Physical properties of sediments play major role for evaluation of protection and preservation of marine environment while strength properties of sediments will come in useful for future mining operations. Cone penetration test (CPT) used for testing in situ is one of methods for investigation strength properties of sediments. The testing apparatus for CPT consists of an instrumented cone having a tip facing down and it is mounted on special underwater equipment (rus. UGI-1). UGI-1 can determine subsurface strength down to the depth interval 0 ? 1.10 m. Special IOM geotechnical cruise was accomplished in 1989 on board R/V Academic A. Karpinski within the extra test area of about 1000 km2. Thanks to UGI-1 the IOM database recorded unique strength sediment data (cone penetration resistance) from 279 seabed points of sounding at profiles 125.6 km long. Up to 35 strength data from depth interval 0-1.1m (every 3cm) were obtained from any particular testing point. As a result 279 strength charts could be plotted (two examples in Figure 1). The cone penetration resistance values can be correlated to shear strength parameters.

Jan 1, 2011

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By Grigori Abramov

As we enter into the 21st Century, miners are looking more attentively at new mining technologies allowing decrease environment damage along with operational cost. This technic would allow developing of poor and difficult mineral deposits, including the World Ocean offshore zone. Borehole Mining is an underground/underwater remote method of mining carried out from floating platforms or vessels. Definition of Borehole Mining (BHM), working schematic, main technical data and its advantages are given. The method is currently in use in mining of different type of raw materials, such as: uranium, iron ore, quartz sand, coal, polymetallic ores, phosphate, gold, diamonds, rare earths, amber and more. It is also in use in oil and gas stimulation, salt domes storages building and environmental problems solution. Recently recorded data of Borehole Mining productivity (80-100 t/hour/hole) and a depth of mining (over 1 km) has been achieved in a last couple years. Remoteness of method not only secures complete safety of operations but also allows wide sector of underwater applications. The World leaders in Borehole Mining are Russia and the United States. Based on previous experience the Universal Tool for Seabed Borehole Mining has been developed for wide sector of usage: from exploration and mining - through oil & gas stimulation to souterrain storages construction and lake's bottom cleaning.

Jan 1, 2000

By Rolf B. Pedersen, Filipa Marques

The extension of the Mid-Atlantic Ridge north of Iceland has collectively been referred to as the Arctic Mid-Ocean Ridges (AMOR). The AMOR extends from the northern shelf of Iceland, to the Siberian shelf in the Laptev Sea, passing en route through the Norwegian- Greenland Sea, the narrow gateway of the Fram Strait, and across the Eurasia Basin. The AMOR is 4000 km long and is divided into six super segments: 1) the Kolbeinsey Ridge, 2) the Mohns Ridge, 3) the Knipovich Ridge, 4) the Molloy Ridge, 5) the Lena Trough, and 6) the Gakkel Ridge. After continental rifting at 60-50 million years ago, around 2.5 million km2 of oceanic seafloor has formed by seafloor spreading - resulting in the formation of the Norwegian- Greenland Sea and the Eurasian Basin. This northernmost part of the global ridge system is anomalous in several ways: The seafloor spreading takes place at an ultraslow rate (less than 2 cm/y) with spreading rates decreasing northward to around 1 cm/y at the Gakkel Ridge - which is the most slow-spreading ridge on Earth. As a result, the volcanic activity along the northern part of the AMOR is low, the oceanic crust is unusually thin (around 3,5 km at the Knipovich Ridge, Kandilarov et al.2010), and the rift valley is deep (average water depth > 3 km). In the southern part of the AMOR, the ridge system is affected by the Icelandic plume and a hot spot below Jan Mayen. The ridge-plume interaction results in higher volcanic productivity, unusually thick oceanic crust (9-11 km, Kandilarov et al. 2012) and shallow ridge segments (1500-100 m). The AMOR also display contrasting spreading regimes, whereas some super segments are dominated by orthogonal spreading (Kolbeinsey and Gakkel Ridge) others are characterized by highly oblique spreading (Mohns and Knipovich ridges). Some ridge segment displays asymmetric spreading, like the Mohns Ridge where core complexes preferentially form along the northwestern flank. Together these variations in ridge characteristics results in large diversity of hydrothermal systems and associated mineral deposits.

Jan 1, 2018

By M. C. I. Modenesi, J. E. Smith, M. Salvá-Ramírez, G. M. Castro, J. C. Santamarina

Annual metal consumption per capita has increased several orders of magnitude worldwide since the turn of the 19th century, yet grades of terrestrial ores are decreasing as reserves dwindle. Consequently, deep sea metal deposits are gradually transitioning from identified resources to economically viable reserves. Deposits in the Red Sea deeps along the axial trough result from tectonic and local hydrothermal processes. Continental rifting and ocean floor spreading produce fresh oceanic crust; concurrently, seafloor evaporites flow into the spreading zone and form isolated deeps. The deeps are often filled with hot stratified brines maintained by locally discharged fluids during hydrothermal circulation. Metalliferous sediments precipitate from the brines within the deeps. The ongoing multipronged study at KAUST involves: (1) acoustic characterization of the metalliferous accumulations using advanced signal processing techniques that capture the physics of granular materials; (2) comprehensive mineralogical and textural characterization of sampled sediments using SEM, EDS, XRD, XRF, and ICP-OES; (3) multiphysics instruments deployed to measure undisturbed sediment properties in-situ; (4) development of a distributed seafloor observatory for monitoring field operations; (5) innovative concentration and separation technologies; and (6) new strategies for proper tailings disposal purposely conceived for the unique field conditions in the Red Sea deeps.

Jan 1, 2018

By S. Jeffress Williams

The U.S. Geological Survey (USGS), over the past three decades, has carried out a spectrum of geologic surveys and research in marine areas of the Exclusive Economic Zone (EEZ) around the U.S. and its territories as well as in the Great Lakes region. Regional and topical studies have been undertaken throughout the range of marine environments: estuarine, tidal wetlands, coastal and nearshore, shelf, slope, and the deep ocean basins. The Survey's coastal and marine research programs consist of four elements shown in Table 1. The first includes studies using interpretations of bathymetry, seismic-reflection and sidescan sonar data, and analyses of sediment grab samples and cores to develop an understanding of the geologic framework. Information on the geologic setting, including the subbottom structure and stratigraphic relationships, and the geologic history and evolution of the areas surveyed are important parts of the program objectives.

Jan 1, 1992

By Hans Smit

The face of mining as we know is changing as mining companies all over the globe realize the reality of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. Previously, the financial and technological implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950s, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business.

Jan 1, 2011

By Mike Woodborne

The marine diamond industry off south-western Africa is maturing rapidly. Some of the larger explorers have reached an advanced stage in their resource development and new mining operations have been started in the last year. Most of the major exploration, mining and marine engineering companies have offices in Cape Town. As a result of the increased activity and experiences to date, new approaches to marine diamond exploration and mining are now evolving. Primary factors contributing the new approaches are namely 1) the concentration of expertise in a localised area 2) the significant increase in the base of available exploration and production results and 3) parallel advances in the marine engineering design and geophysical survey equipment. The sea floor geology and setting of the marine diamond exploration areas is now better understood. Consequently the strategy for exploration and the selection of appropriate survey equipment is improved. Due to new equipment developments, different exploration alternatives now exist, depending on the programme objectives. Significant advances have also been made in the data processing and modelling undertaken to assist in the identification and targeting of potentially diamondiferous prospecting features. Similarly, the design of appropriate prospecting tools and programmes has also been improved. Following exposure to the requirements of the marine diamond industry, the design engineering and operating companies have responded with innovative designs for new prospecting tools. In recent years the availability of relevant information on marine diamond prospecting and production has increased. As a result, there is now sufficient basis for the construction of meaningful financial valuation models that can be effectively used to control and guide the exploration projects, to the benefit of both the explorer and the investor.

Jan 1, 1998

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer's standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By V. Zaykov

The Urals massive sulfide deposits are concentrated in Silurian -Devonian fold belt extending for 1500 km with length from 50 to 150 km. By paleodynamic reconstmction it is established that they were formed in submarine parts of island arcs, in inter arc and back arc basins, marginal seas. When "black smokers" were found in rift zones of present oceans, problem searching their analogues in the Urals Paleozoic complexes was arisen. For solving this problem and demonstration of seafloor origin of massive sulfide many quarries and drill cores were carefully sketched and studied. Particular attention was given to correlation between ores and synchronous sedimentary rocks and fossils. Various laboratory methods were used for comparing sulfides from ore hills with ore-clastic sulfides.

Jan 1, 1993

By Ye Jun

Until now, more than 200 sites of sea-floor hydrothermal activities are known on the midocean ridge but few of them are documented on South Mid-Atlantic Ridge (SMAR). This on some extent restricts our directly understanding of the hydrothermal mechanism on SMAR. In 2011, During the Cruise 22 of R/V Dayangyihao, a masive sulfide field was discovered in the center part of the first-order ridge segment that bounded between Cardno Fracture Zone and Saint Helena Fracture Zone, near 15.16°S/13.35°W, which give us an opportunity to recognize the mechanism of hydrothermal systems on SMAR directly. This newly discovered hydrothermal field, which informally called SMAR 15°S, is situated in a SE-NW offset depression of an axial neovolcanic ridge, with water depth of about 2793m. In the water column around this field, strong turbidity and temperature anomalies were detected. Ten meters high venting chimneys, hydrothermal mounds as well as a large amount of hydrothermal vent shrimps were also observed and recorded by ROV and Deep tow camera on the ocean floor. The samples we collected from this field include sulfide chimney fragments, massive sulfides and basaltic rocks. In this study, we are focusing on the mineralogy and sulfur isotope geochemistry of sulfide samples for preliminarily uncovering the geological characteristics and hydrothermal processes of this hydrothermal field.

Sep 14, 2011

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By Richard H. T. Garnett

The Chilean part of the archipelago of Tierra del Fuego, situated south of latitude 62o S, is within that country?s Región de Magallanes y Antártica, and separated from the remainder of Chile by the Magellan Strait. In recent geological history several phases of Quaternary age glaciers originating in the Andean and Dawinian Cordilleras eroded assumed primary gold deposits and entrained their related alluvial deposits. Piedmont glaciation extended to the east and south over m0st of the land and beyond the present-day coastline into extensive areas exposed during the resulting lowered relative sea level. During interglacials particulate gold incorporated unevenly in the widespread drift, till and moraines was fluvially released and concentrated into streams and flood gravels. Coastal erosion enriched various beaches with gold. From 1868 onwards Tierra del Fuego hosted a major gold rush whereby early, labour intensive, beach mining eventually developed into inland dredging. But continued mining activity was interrupted and then terminated by several external factors. Most miners, always seeking ?greener pastures?, joined the rush to the new discoveries in the Klondike (1896) and Nome, Alaska (1899). In 1904 the international boundary, established in 1881, became the subject of a major dispute not settled until 1984, The Panama canal?s opening in 1914 turned Tierra del Fuego, previously on the Pacific-Atlantic shipping route, into a remote backwater. World War II brought opposing foreign naval forces to the actual islands where most gold had been taken from the beaches. It also crippled the dredging industry which lost its coal supply and never recovered. Nevertheless, some small scale mining continues to this day.

Sep 14, 2011

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By Malcolm Clark, Robin K. H. Falconer

There are a number of likely impacts from mining operations, but a key issue is uncertainty about the environmental effects of sediment plumes created by disturbance to the seafloor and discharge of processed waters. The New Zealand National Institute of Water and Atmospheric Research (NIWA) is undertaking a research project to improve understanding of such impacts (relevant to both mining and trawl fisheries), by examining the extent and persistence of sediment plumes, the immediate impact and subsequent recovery of seafloor exposed to these plumes, and the effect on functioning of ecologically significant species. The project will use a combination of field survey experimentation with in situ observations and controlled laboratory-based experiments. The field work begins in May 2018 when an area of up to 1km2 at depths of 400-500 m on the Chatham Rise, 450 km east the New Zealand South Island will be subjected to disturbance by an upgraded former NOAA Benthic Disturber. The suspended sediment load created by the disturbance will be tracked and monitored, with the effects on seafloor animals examined by pre-and post-disturbance sampling. A wide range of seafloor sampling, benthic landers, towed cameras, oceanographic moorings and water column monitoring will be carried out over a three week period. Monitoring surveys will be repeated in 2019 and 2020 to determine the longer-term resilience and recovery of disturbed communities. The laboratory-based side of the programme, also starting in 2018, involves holding live deep-sea corals and sponges in tanks at NIWA, and exposing them to various levels and duration of particle loads in the water in order to reveal lethal thresholds as well as sub- lethal effects of settled and suspended sediment.

Jan 1, 2018

By Carl H. Hobbs

The needs of the on-going basic maintenance operations and proposed enhancement and hurricane protection projects in the City of Virginia Beach exceed the capability land-slide sources of sand. Through the past several years our studies have concentrated on locating and defining suitable quantities of sand appropriate for use on the area's beaches and assessing some of the consequences of dredging in shallow offshore areas. By providing information concerning the geological setting of sand resources, the local wave climate, and benthic infauna, the overall research project has strengthened the knowledge and understanding of several facets of Virginia's inner continental shelf. We have identified three distinct settings for deposits of beach-quality sand, two of which (filled channels and surficial shoals) are distinguishable in relatively unprocessed sub-bottom profiles and cores. The third, a sand facies within a larger stratum, is discernable only with a suite of cores. Sandbridge Shoal, about 5 km offshore of the resort and residential community of Sandbridge appears to contain a substantial quantity of sand that could be exploited with comparatively few problems. It already is designated as the source of material for use in a shoreline protection protect for a federal facility. Fluvial(?) fill of a late Pleistocene channel lust offshore of the main, commercial, resort area may offer a proximal alternative to existing and proposed resources. Ongoing work to describe the local wave climate and the possible impacts of anthropogenic alterations of the bottom topography on wave transformation and studies of the biological community as it might be affected by dredging will help fill-out our series of studies. Prior to utilization of the resource additional work is needed to provide better definition of the limits and magnitude of the sand bodies. Finally decisions concerning the use of specific resources will have to include physical, biological, economic, technical, and social considerations.

Jan 1, 1996

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011