Search Documents

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

By Harold Gibson, Ulrich Schwarz-Schampera, Ralf Freitag, Hendrik Mueller

INTRODUCTION Germany has a long history in marine research in the Indian Ocean. The first German scientific cruise started in 1964, followed by a series of state-sponsored research cruises between 1983 and 1995 leading to the first finding of polymetallic sulfides in the Indian Ocean. The research included regional bathymetric, geological, structural, volcanological, petrological and hydrothermal investigations along the Carlsberg Ridge and the Central Indian Ridge (CIR). Early environmental base line studies covered oceanographic and sedimentology aspects. In 2010, BGR took the initiative for the preparation of a license application for the exploration of polymetallic sulfides with the International Seabed Authority (ISA), and prospecting started in 2011 along the southern Central (CIR) and the northern Southeast Indian Ridge (SEIR) in the southwestern Indian Ocean (cruises INDEX 2011 on board R/V Sonne), INDEX 2012 (R/V Fugro Gauss), INDEX 2013/1-2 (R/V Sonne) and INDEX 2014 (R/V Pelagia). After three years of resource-oriented and environmental base line studies, BGR, in order for the Federal Ministry for Economic Affairs and Energy (BMWi), applied for an exploration license which was approved by and subsequently signed with the ISA in 2015. The license gave permission to start a detailed exclusive resource-oriented exploration program in the license area. The program includes the outline of potential ore deposits and a resource assessment but also extensive and detailed base line studies for the sustainable protection of the marine environment in the license area. The license contract has a fifteen years lifetime and may allow the application for a subsequent mining license. The exploration aims at the identification of inactive polymetallic sulfide deposits, formed below former discharge zones of hot hydrothermal fluids on the ocean floor (“black smoker” systems), by advanced and modern exploration techniques.

Jan 1, 2018

By J. A. Jankowski

The situation in the raw material market has brought into consideration the commercial exploitation of the mineral deposits on the deep sea bed and in particular the manganese nodules. They occur generally in depths of 4000-5000 m, partially covered or buried in bottom sediments. The deposits and their potential recovery have been intensively explored and researched during the past twenty years (Bischoff 1979, Halbach 1988, Padan 1990). Although the present market situation limits the rentability of deep sea mining on an industrial scale, the mining technology is being further developed in many countries. The stagnation phase in the deep mining issue allows sufficient time for conducting research on the precautionary protection of the deep sea environment and for consultation in the development of technologies with the least possible impact on it. The subject has gained in importance since autumn 1994, when the United Nations International Law of the Sea was signed. This also regulates human activities in international waters from the environmental point of view. As fields tests have shown in the past, even with the most modern technologies, mining of the manganese nodules will inevitably be accompanied by a resuspension of some bottom sediments. The generated sediment plumes will be further transported with the ocean currents and in the worst case form stable turbidity layers in different depths (Ozturgut 1981a, Baturin 1991). One of the problems of the environmental impact assessment is the estimation of the plume persistence before it eventually dilutes to approximately the ambient concentration level or settles at the bottom (Lavelle 1981a, Lavelle 1981b, Lavelle 1982, Thiel 1991a, Thiel 1991b). The aim of the research is to develop a numerical sediment transport model in connection with potential manganese nodule mining in a reference area located in the southeastern equatorial Pacific Ocean off Peru (Peru Basin, Discol Experimental Area). In this region, a German mining claim is registered and interdisciplinary field works of the TUSCH (German: TiefseeUmweltSCHutz, deep sea environmental protection) research group are carried out in order to obtain the required scientific background for evaluating of the deep sea mining impacts and to provide the necessary supporting data for the modelling (Thiel 1991a, Thiel 1991h).

Jan 1, 1995

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By Richard T. Haworfh

The United Nations Convention on the Law of the Sea (UNCLOS) entered into force, for those nations who had ratified it, on November 16, 1994. The Convention deals with nearly every aspect of ocean affairs, including marine scientific research, fishing zones, freedom of the high seas, protection of the marine environment and deep seabed mining. Article 76 of the Convention defines edge of the continental shelf in a way that many earth scientists find bizarre. Out to this limit, a coastal state has sovereignty over the seabed and sub-seafloor resources. Beyond that limit, the key principle of UNCLOS, that "the resources of the deep seabed represent the common heritage of mankind and should be developed to benefit all nations" is invoked. Establishing that limit and managing development in the different areas of jurisdiction is no small task. Canada's continental shelf as defined by UNCLOS covers an area approximately equal to half the area of the Canadian land mass. Interpretation and application of the convention is therefore highly significant for Canada. For example, the sedimentary basin in which the offshore Hibernia oil field is found, extends beyond the 200 mile limit but lies predominantly within the limits of the (UNCLOS) continental shelf. Responsibility for development of inshore placer deposits rests firmly with the coastal state. However, development of deep sea mining, in which the international community plays a management role under UNCLOS, has raised many concerns. Of particular interest to Canada will be the application of the provisions of the convention to interest in the polymetallic sulfides sampled on the mid-ocean ridges such as the Juan da Fuca Ridge. A further complicating factor for Canada is management of fishing stocks. Canada has sought to resolve this "problem" through multilateral negotiations under the UN. Under its "Oceans Act," currently being debated by Parliament, Canada intends to become a world leader in oceans and marine resource management. Similar activity in most maritime nations is setting the stage for a revolution in the way in which use of the world's oceans is managed. Much of this revolution will be guided by UNCLOS. Coastal states that have ratified the convention have ten years in which to define the limits of their continental shelves the clock is already ticking for them! We have yet to see how their actions will guide, or be guided by, those who have not yet ratified. We also have yet to see how national legislation and aspirations will mesh with international conventions that were drawn up in a previous era of environmental standards. This is a time in which many questions have been raised and few firm answers received. However, we must ensure that everyone is aware of what is happening, with what potential consequences, in order that rational decisions can be made. Canada has taken a few small steps that it is happy to share with the world community.

Jan 1, 1996

By Richard H. T. Garnett

Marine mining on the continental shelf was first attempted in 1900 for gold off the beaches of Nome, Alaska. Attempts continued until 1990 with cutter-suction, airlift and bucket-ladder dredges. Offshore Thailand profitable production of tin resulted from clamshell, bucket-ladder and trailing suction hopper dredges. Today in Indonesia numerous bucket-ladder dredges continue to mine tin. Off the coast of Namibia and South Africa nearly a dozen large and medium sized vessels are engaged in diamond production. The obvious risk results from the working environment. Vessels and lives have been lost in the past. At best the availability of mining equipment is reduced. Leaving aside the marketing and financing aspects, otherwise the most important risks are technical. They manifest themselves as diamond production short-falls with obvious financial consequences. Bias and deficiencies in sampling equipment and procedures may result in misleading grade estimates, even serious under-estimation. Inadequate sampling in terms of sample support and density may result in over-optimistic grade determinations, especially if under-sized mining blocks are outlined. Quantitative measurement of the geotechnical characteristics of the sediments to be mined is an essential stage in a feasibility study. Without a full understanding of the bedrock profile and the overlying sediments the ease, completeness and speed of excavation during the mining process cannot be properly estimated. Both historically and at present the greatest negative discrepancies from production estimates result, not from grade shortfalls, but from significantly lower mining rates than thought possible by the operators. The learning curve in marine, production mining is steeper and longer than is generally recognised by newcomers to the industry. Examples are provided from tin, gold and diamond mining experiences.

Jan 1, 1998

By Tatiana ?. Sedysheva, Vladimir V. Ivanov, Michail E. Melnikov, Irina A. Pulyaeva

"INTRODUCTIONHydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean [3, 4 - 8]. Now, commercial interests gain more and more attention. Mining systems are being developed which involve fragmentation of the crusts and their separation from the substrate. The effectiveness of such activities greatly depends on physico-mechanical characteristics of the crusts and rocks on which they form. This determines the importance of the engineering geological study of the objects.This article comprises the results of the engineering geological studies of the crusts samples (72 samples) and their underlying rock substrates (75 samples), which were carried out during the research cruises 6-06, 6-07, 6-08, 6-13 (2006-2013) on the Magellan Seamounts guyots in the Western part of the Pacific Ocean by the specialists of the State Scientific Centre Yuzhmorgeologia [10 - 13, 19, 20]. The authors of the article directly participated in the studies mentioned above.MethodsEngineering geological studies were carried out on board of the research vessel Gelendzhik and in the laboratories of NPA «Sevmorgeologiya». The studies involved the determination of the following parameters:"

Jan 1, 2017

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By W. H. Pelton

Polymetallic sulphide (PMS) deposits have recently been discovered associated with hydrothermal vents on the sea floor off Vancouver Island, B.C. Visual estimates indicate reserves in excess of 1 million tons. Reliable reserve estimates have not yet been made, however, due to the extreme difficulty of drilling cores in 2 km of water. Few geophysical techniques can aid in the exploration of these deposits. There is little or no difference in radioactivity, magnetic susceptibility or electrical resistivity between the deposits and the surrounding sea floor sediments. This precludes radiometric, magnetic, electromagnetic and resistivity methods. There is a density contrast, but the logistics of gravity surveys at such depths are formidable. The physical property which shows the most contrast with the sea floor sediments, and which is perhaps one of the easiest to measure (with modern equipment) is polarizability. The induced polarization (IP) method is one of the major electrical geophysical techniques for exploring for PMS deposits on land.

Jan 1, 1985

By Chan Min Yoo, Jung-Keuk Kang, Wonnyon Kim

Recently high-resolution paleomagnetic age determination of ferromanganese crust in less than millimeter scale has been successfully carried out using a superconducting quantum interference device microscopy magnetometer (SMM). However, it has not been clearly identified how the crust is keeping ancient geomagnetic field records. Here we try to identify magnetic mineralogy of the crust obtained in the Magellan Seamounts, the West Pacific (~20 °N). As a record, age of the crust used in this study is extended to ~10 Ma at ~40 mm depth and ~28 Ma at ~100 mm depth, respectively, based on the combination approach of SMM measurements, Be-isotope and Co-chronology. Thermal demagnetization revealed a Curie temperature of ~560oC, corresponding to (titano)magnetite. Component analysis of isothermal remanent magnetization identified a presence of two types of magnetite. Measurements of first order reverse curve showed a dominance of non-interacting single-domain magnetite, which is one of the intrinsic feature of biogenic magnetite. Although most of the magnetic particles on transmitted electron microscopy are covered by amorphous Fe-Mn minerals, some are observed as a prototype of biogenic magnetite showing a chain of ~10 nm sized magnetite cubes. However, a magnetite signal (i.e., Verway transition at ~ –120 oC) was not detected in low-temperature treatment probably due to surface oxidation of magnetite. Contribution of interacting magnetite of detrital origin is <30% throughout a crust. Interestingly, contribution of detrital magnetite is almost three times higher since ~10 Ma. At this boundary, a growth rate of the crust is double up and flux of other detrital signals, including Al, Mg, Ti and Zr, are also increased.

Jan 1, 2017

By Igor E. Mikhaltsev

This paper concerns the continuation of work on the deepwater non-oxygen cycle heat energy generating systems. The 25-kW prototype of a universal deepwater turbine-electric energy source with hydrazine-hydrate as the primary heat production chemical is described in short and its abilities are discussed. The ?hydrazine-hydrate 64? is a catalytically dissociated heat production chemical (H2H4 ? nH2O) with 36% of water. The system was designed for work in any depths of the ocean down to 6000 m. It was built and tested working in the testing chamber in the ambient hydrostatic pressure of 600 bar. Then it was tested in the autonomous programmed regime in the Atlantic Ocean. The privileges of that energy system for any bottom installations or moving devices designed for ocean mining which need high power energy sources (20-100 kW and more) are discussed. The important needed step forward is raising the efficiency of the system which needs some investigation work in known directions. It is supposed that the possibility of getting about 5 kg/kWh with improved battery charging possibilities could be achieved. This might make the system even more profitable for mining operations.

Jan 1, 2001

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By Elisabetta Tedeschi, Razieh Nejati Fard

Deep-sea mining is in the future perspective of mining industry and it is currently in the technological development phase. The focus of this study is on the electrical power system that provides sufficient energy for the mining equipment at the seafloor, excavating Seafloor Massive Sulfide (SMS) deposits. SMS deposits usually exist at water depths between 1500 m and 4000 m. Despite the similarities of SMS deposits excavation to the open-pit terrestrial mines, more energy is required to drill and crush the ores in the hyperbaric conditions [1], which can be done whether by static trench cutters [1] or by mobile mining crawlers [2]. In addition, the ores vertical transportation by subsea pumps requires several MW electrical power that can be supplied by all-electric subsea motors or hydraulically from water injection motors located on the surface. The power requirements can be fulfilled by an offshore or subsea power network. As the SMS mines are usually in remote locations, the straightforward solution will be an isolated offshore grid mounted on a vessel or platform similar to the most of offshore Oil & Gas projects. These power systems resemble the onshore microgrids for industrial purposes operating in island mode. However, in contrast with the onshore power networks, there are space and weight limitations in offshore infrastructures, which impose the design compactness to be a priority. In addition, having a very high reliability is necessary in the design approach of the offshore projects due to the extraordinary high expenses corresponding to repair and maintenance. The other design criterion is to improve the power system efficiency in order to reduce the size of the power equipment cooling apparatus, operational costs and CO2 emissions produced by diesel/LNG onboard generators. There are a few studies considering power system distribution for seafloor mining industry. Among them, [3] has investigated the AC and DC alternatives for SMS mining in 2400 m water depth by considering Solwara 1 project scenario introduced by Nautilus Minerals Inc. [2]. In this study, a power system design tool will be presented taking into account various water depth, power consumption levels, different distribution configurations (AC and DC) and the aforementioned design criteria.

Jan 1, 2018

By David S. Cronan

The traditional method of deep sea manganese nodule exploration is to conduct grid survey and sampling on successively finer scales until a suitable deposit has been delineated. Clearly this is both time consuming and ultimately self-defeating if large areas of the ocean floor are to be explored on a human timescale. A conceptual deductive approach would be preferable if one could be found, as it would aim to outline areas of potentially economic nodules on the basis of easily measurable oceanographic parameters. An attempt to achieve this aim in the Central Pacific is outlined below. Nodule Distribution in the Central Pacific Ocean Maps of ore grade nodules in the Central Pacific show that they are confined to two zones trending roughly east-west which are well separated in the eastern Pacific but which tend to converge towards 170-180ºW. They follow the isolines of intermediate biological productivity in the surface waters, strongly suggestive of a biological control on their distribution. Within these zones the nodules preferentially occupy basin areas. Thus they are found in the Penrhyn Basin, Tokelau Basin, Central Pacific Basin, Clarion Clipperton Zone and Tiki Basin. Nodules in all these areas have features in common and are thought to have obtained their distinctive composition by similar processes.

Jan 1, 2003

By T. Yamazaki, R. Arai, N. Nakatani, K. Kuroda

"These 40 years, deep-sea mining for manganese nodules, cobalt-rich manganese crusts, and seafloor massive sulfides has been continuously business and R&D targets. The economy is the most important factor for realizing the venture. Some technological options to increase the economy of deep-sea mining are introduced. They are a mechanical lift, waste rejections on seafloor, a substrate recovery as byproduct, and a pulp lift. An example application of one of the options is economically examined. Not only the same type examinations but also some technological clarifications of the options in detail are necessary.BACKGROUNDManganese nodules (nodule), seafloor massive sulfides (SMS), and cobalt-rich manganese crusts (crust) have been well recognized as future metal sources these 40 years. Among them, the nodule was the first recognized ones. The mining technologies for the deep-sea mineral resources, therefore, have been mainly developed in the major R&D projects for the nodule.The mining systems considered were shuttle miner, continuous line bucket (CLB), and hydraulic dredge ones. The shuttle miner system studied by France was a kind of basic study for autonomous underwater vehicle. The CLB system was an effective approach for a small scale and less investment cost mining (Masuda and Cruickshank, 1995). However, both were considered not effective for a bulk scale production rate mining such as 1.5 million tons per year in dry weight. In the hydraulic dredge system, a steel-pipe and flexible-hose conduit for nodule transportation named “pipestring” and a hydraulic pumpup instrument for creation of upward water flow in the pipestring named “pump-lift” or “air-lift” were adapted and developed. Hence, the hydraulic dredge system became the main stream in the mining system."

Jan 1, 2017

By Toru Yamasaki

"Bimodal lithostratigrafic assemblages are of significance in volcanogenic massive sulfide (VMS)-hosted lithology. The largest deposits are either bimodal-siliciclastic or maficsiliciclastic, and the presence of a significant siliciclastic component in the host stratigraphic succession favors large VMS deposits (e.g., Franklin et al., 2005; Barrie and Hannington, 1999). In the case of modern sub-seafloor VMS deposits in arc-related settings, the majority of deposits have been discovered in association with calderas or cauldrons (Halbach et al., 1993; Ishibashi and Urabe, 1995; Iizasa et al., 1999). These features are formed by the explosive eruption of silicic volcanoes, so that silicic host rocks and/or pumiceous volcanic clasts are generally observed around the ore deposits (e.g., Binns and Scott, 1993; Fiske et al., 2001). Caldera-like and graben-like morphological features therefore attract attention in geophysical surveys. However, silicic lithologies (dacite and rhyolite) normally contain only small amount of metallic elements (e.g., a few ppm to a few dozen ppm of Cu), whereas mafic rocks, such as basalts and basaltic andesites, contain significant amounts of metals (e.g., a few hundred ppm of Cu). Thus, the origin of metallic elements in VMS deposits associate with the silicic host rock remains unclear.The Iheya North Knoll is a volcanic complex in the middle of the Okinawa Trough. It is located in a young and actively spreading back-arc basin that extends for 1200 km behind the Ryukyu arc-trench system (Lee et al., 1980; Letouzey and Kimura, 1986). Several active hydrothermal fields have been recognized in the Iheya North Knoll. Mineralization at the Iheya North Knoll is characterized by relatively juvenile features consisting of VMS deposits with associated hydrothermal alterations to various degrees. Massive sphaleriterich sulfides at this site, recovered for the first time from beneath an active seafloor hydrothermal system, strongly resemble the black ore of the Kuroko deposits of the Miocene age in Japan (Takai et al., 2011). From February 11 to March 17, 2016, the SIP CK16-01 (Exp. 908) D/V Chikyu cruise was conducted at Iheya North Knoll and the rifting center of the Iheya Minor Ridge area, middle Okinawa Trough. The Iheya Minor Ridge area is also an active hydrothermal field, located ~30 km southeast of the Iheya North Knoll. In this area, basaltic rocks are widely distributed, and drilling has confirmed that the basaltic materials continue to ~120 m below the seafloor (Kumagai et al., in prep)."

Jan 1, 2017

By Derek Ellis

There are two environmental issues which have only recently begun to need planning in detail for marine mining. One is the environmental consequences of mine closure; the other is environmental terrorism. In principle it is not difficult to predict the pattern and rate of biodiversity recovery after mine closure on metalliferous depositional seabeds. 1-5 years to a self-sustaining community of organisms is a generalized guideline, depending on depth and particulate composition. The rate and pattern of biodiversity recovery on some metalliferous hard-rock habitats is far less predictable due to the patchiness and rareness of the habitat. Ecoterrorism at mines, whether on-land or marine, is now to be expected. A good example of resource industry ecoterrorism is the fire-bombing of logging and cement trucks in Oregon in 2001. But there have also been bombs at mine sites, as at Asbestos, Quebec. It is also possible to regard some resource-loss lawsuits as frivolous, hence forms of ecoharassment. Marine mining operations should take note of the development of environmental terrorism (and terrorism in general) and its various manifestations and impacts. Potentially these range from minor work stoppage inconveniences, to serious financial risk jeopardizing the economics of a mine, to jail for company executives, managers and environmental staff, and to harassment and killing of mine personnel.

Jan 1, 2005