Search Documents

In early 1990s, the Korean government has launched a deep-sea research program to secure the stable long-term supply of strategic metallic minerals including Cr, Cu and Ni. Through the pioneering surveys, Korea registered 150,000 km2 of Mn-nodule field in the Clarion-Clipperton area, the NE equatorial Pacific to the international sea-bed authority (ISA) in 1994. Following the ISA exploration code, the final exclusive exploration area of 75,000 Km2 was assigned in 2002, based on results of eight-year researches of chemicophysical properties of nodules, bottom profiles and sediment properties. Since that time, environmental studies, mining technical developments including robot miner and lifting system and establishment of smelting systems were accompanied with the detailed geophysical studies to decipher the priori mining area until 2009. Major points of the recent Korea Mn-nodule program are deployed on a commercial scale until 2015. In order to meet the goals, detailed 25,000 scaled mining maps in the priori area will be prepared, which can provide operation roots of the miner. In addition, an environmental-friendly mining strategy will be pursued based on the environmental impact test and environmental monitoring.

Sep 14, 2011

By Dennis Sánchez Mora, John Jamieson

INTRODUCTION Work by Humphris et al., (2002); Ondréas et al., (2009); Barreyre et al., (2012); and Escartín et al., (2015) has identified active and inactive hydrothermal sites along the Lucky Strike segment. The sites that contain the largest accumulation of known sulfides are located between the north and the southern zones (Figure 1), a vent site area that is referred to as the Main Lucky Strike hydrothermal field (Escartín et al., 2015). Hydrothermal fluid outflow has been linked to a shallow fault network (Barreyre et al., 2012). However, specific constraints on fault geometries have not been determined. Other off-axis sites at Lucky Strike, such as Capelinhos (high temperature vent), and Grunnus (inactive?), as well as a low temperature vent field (on-axis), Ewan, have been described by (Escartín et al., 2015). Given the spatial relationship between the Main Lucky Strike hydrothermal field (MLSHF), and the intersection of northern rift faults with the southern rift faults, a structural analysis of this area can provide insight into the fault controls on fluid flow that leads to hydrothermal venting and sulfide precipitation. METHODOLOGY Structural data (dip direction and dip) was determined using Leapfrog Geo 4.0 software. Bathymetric data was obtained from Escartín et al., (2015) and references therein. The bathymetry was imported into Leapfrog Geo (in UTM format) and, using the structural modelling tool, individual measurements with dip direction and dip data were collected with a focus on the northern volcanic rift and the southern central volcano (Figure 2a). All measurements were taken from what the authors consider as normal faults, and to aid the determination of individual measurements a “face dip” map was constructed, where the bathymetry is colored by slope angle (Figure 2b). All measurements are simultaneously plotted on a stereonet generated by the Leapfrog Geo Software. Data were divided into northern and southern, and western and eastern zones to determine the relationship between hydrothermal venting and the structural geometries at Lucky Strike (Figure 2c). Slip measurements for individual faults were determined along the dip of the fault with a measuring tool. Net slip, heave (horizontal displacement), and throw (vertical displacement) was calculated for each of the zones.

Jan 1, 2018

By Richard H. T. Garnett

Diamonds were discovered on the coast of Namibia in 1907 but it was not until 1962 that the first gems were produced from offshore by a barge employing an airlift. Geophysical surveys and a sampling program were initiated and an understanding of the diamond distribution was gained. Several vessels, some with multiple airlifts, were used until the early 1970's. Some spectacular production results were achieved, but generally the systems failed to retrieve the gravels efficiently from beneath the overburden and off the bedrock. Various companies continued working with mixed outcomes until the mid-1980's, when new regulations were enacted by the authorities. The local Southern sea conditions dictate the present mining methods which are now applied over several hundred kilometers of the west coast. In shallow waters divers operate from small vessels, suctioning the diamondiferous gravels to surface with gravel pumps. In water depths of up to 50 m airlifts of various designs continue to be utilized with recovery plants installed on the vessels. Beyond 100 m depths a remote controlled, tracked, vehicle is used, together with a large drill mounted on swell compensator. Each system is deployed from a separate ocean-going vessel. Production of diamonds from the offshore is rising rapidly, with expectations of further increases. The coastline is likely to be the scene of new developments in marine mining techniques.

Jan 1, 1992

By Roy Nilsen, Aravinda Perera

With the exponential growth of demand for minerals and need for diversification of supply channels, deep-sea mining is rapidly becoming inevitable. Productivity of underwater mining technology is salient to justify the deep-sea explorations. Methods for enhanced productivity of mobile mining equipment in a system level are investigated in this paper. Lessons learnt from the land-based mining has been the basis of this investigation. In general, mining productivity can be enhanced in two ways; firstly, by maximizing the amount of recovered material per unit time and secondly, by minimizing the cost of operation per unit material. Equipment that enable faster excavation, loading and transport in the seabed contributes significantly in increasing the amount of slurry per unit time. Improved mean time between failures (MTBF) of mining equipment will reduce the operational down time, thereby, contribute to maximize the amount of mined material per unit time. Several factors influence the operational cost minimization per ton of slurry. Higher efficient motor drive systems including the motor and PWM-fed inverter not only will save power but also will emit lesser heat thus the heat management can be less complex. This leads to more compact drive systems that allows higher power density, thus increased payload weight per empty vehicle weight. An energy storage method in the form of an utracapacitor in the electric drive system will also save the energy supply from the upstream.

Jan 1, 2018

By R. W. Nesbitt

The TAG and Broken Spur hydrothermal mounds are located on the Mid Atlantic Ridge (MAR) at 260N and 290N (respectively). Both were initially discovered by exploratory work from surface vessels and both have since been investigated by submersibles. The discovery of TAG resulted from a NOAA Trans-Atlantic Geotraverse (Rona et al. 1975) which fortuitously sampled low temperature materials on the east wall of the MAR rift valley and follow up operations (Rona et al. 1986) located the high temperature (365°C) mound some 5km to the west. In 1994, ODP deep sea drilling (Leg 158) at over 3,500 metres of water recovered core to a depth of 150 m below surface (Herzig et al. 1998) and for the first time allowed a geological interpretation of an active mound. The Broken Spur mound was accidentally discovered in 1993 when sulphide fragments were observed on a deep-sea towed camera system (Murton 1993). Later that year, exploratory submersible dives by Alvin located the hydrothermal field and the area was again explored by submersible in 1994 and 1997. Despite the amount of work carried out, our geological understanding of the MAR mounds is limited. Much effort has gone into measuring fluid chemistry whilst practical difficulties have inhibited good geological mapping of the sulphide areas. It is clear from both TAG and Broken Spur that the mounds are not necessarily located in the areas of highest heat potential. Indeed, TAG is some 2 km from the rift valley axis and has been operational for several tens of thousands of years. Hence, heat availability is not a major consideration and the most obvious control is a structural one. Mapping on Broken Spur indicates a series of isolated vent-sulphide areas, concentrated around a minor graben. Their distribution, size and nature all indicate that they are residual parts of a much larger sulphide body which was at least the size of the present TAG field. The evidence is for a cyclical pattern of mound growth -mass wasting? rejuvenation and the Broken Spur mound appears to be in the rejuvenation stage of the cycle. Mound cyclicity must be related to the supply of hot water which itself is a function of the connectivity of fracture systems. Hence, we return to the theme that the major controls in mound development are structural ones.

Jan 1, 1998

By Toru Yamasaki

A concept of plate-tectonic controls for the formation of seafloor massive sulfide (SMS) deposits in back-arc settings was established by Franklin et al. (2005). According to Franklin et al. (2005), a consequence of extension and rifting is subsidence, thinning of the crust, and the rise of hot, athenospheric mantle into the base of the crust. Underplating of the crust by mafic magmas results in low-pressure partial melting of the hydrated crust at a <15-km depth, and the generation of felsic anhydrous melts. The rapid ascent of hot felsic melts, along with mantle-derived mafic melts, results in bimodal volcanism that characterizes rift and volcanogenic massive sulfide deposits (VMS) environments. The rapid and focused advection of the magmatic heat within the rift to the near-surface environment which are required to sustain vigorous long-lived VMS hydrothermal systems. Faults within rift environments may also allow seawater to penetrate into subvolcanic intrusions and mix with magmatically generated metalliferous fluid or allow a direct magmatic contribution from shallow crustal level (3–12 km) magma chambers (Franklin et al., 2005, and references therein). In addition, the caldera-forming processes are favorable for the formation of VMS deposits and the focused high heat flow and cross- stratal structural permeability that is restricted in time and space to caldera development provides an explanation for the clustering of VMS deposits and their restriction to specific time-stratigraphic intervals and structures in the evolution of submarine central volcanic complexes (Franklin et al., 2005, and references therein). The concept is persuasive, although it is based on a series of logically constructed reviews mainly focused on ancient on-land deposits.

Jan 1, 2018

By Carl L. Kaiser

This abstract discusses selected recent technology developments at the Deep Submergence Lab at the Woods Hole Oceanographic Institution aimed at fundamentally changing the nature and scope of AUV operations in the deep ocean. The Autonomous Underwater Vehicle (AUV) Sentry is described in its current configuration with discussion of emerging capabilities. Telepresence enhanced AUV operations are discussed including moving both operations and data processing personnel off the vessel. Autonomous Surface Vessel (ASV) aided AUV operations are discussed including recent experiments where an ASV provided both navigational aiding and a satellite based relay for acoustic communication of telemetery and mission redirection. New flexible communications strategies to perform intervention and manipulation tasks from an untethered vehicle are discussed. The abstract concludes with a brief discussion of industrial collaborations, including the newly launched Center for Marine Robotics.

Sep 14, 2011

By Mark D. Hannington

Seafloor polymetallic sulfides have been found in diverse volcanic and tectonic settings on the ocean floor at water depths ranging from 3700 meters to <1500 meters. More than 100 occurrences of hydrothermal mineralization have been documented (including Fe-oxide deposits, Mn-crusts, metalliferous sediments, and massive sulfides), but high-temperature hydrothermal activity and large accumulations of polymetallic sulfides are known at fewer than 20 different sites. Chemical analyses of samples from these deposits indicate that they contain important concentrations of Cu, Zn, Ag, and Au, comparable to those of massive sulfide deposits on land. However, the lack of sufficient data concerning the distribution, size, and bulk composition of seafloor deposits precludes a meaningful assessment of their resource potential.

Jan 1, 1994

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By S. Rajendran

Gas Hydrates (Methane Hydrates) are solid, ice-like substances composed of water and natural gas. They occur naturally in areas of the world where methane and water combine at appropriate conditions of temperature and pressure and are found in ocean bottom sediments and in some permafrost areas. Besides temperature and pressure, factors like bathymetry, sediment thickness, sedimentation rates, and total organic carbon content (TOC) also control gas hydrate formation in the ocean basins. The stability of gas hydrates depends on the critical combination of high pressure and low temperature (0 - 17 bars, 0 - 25°C), which in turn is dependent on the mix of gases from which the mineral is formed. As the critical parameters can be altered by deposition, erosion, slumping, formation or melting of ice cover, rise and fall of sea level, and sudden temperature changes induced by tectonic activities, current flow, or volcanisms, the gas hydrates tend to be very unstable. The Indian offshore is promising for the occurrence of gas hydrates in a total of about 80,000 km2 area in the bathymetry range of 700 to 3000 m as reported in earlier surveys. A gas hydrate stability zone thickness map was prepared using bathymetry and sea bottom temperatures along the continental margins of India. This map is expected to provide the depth window while searching for Bottom Simulating Reflectors (BSR). The study indicates that a minimum water depth of 750 m is required for the formation of gas hydrates, above which the chances for gas hydrate occurrence appear minimal despite other favorable conditions like organic-rich sediments, etc. Single-channel seismic analog records (Gupta et al., 1998) indicate that the Western Continental Margin of India (WCMI) offers a greater promise for gas hydrate occurrences, particularly with regard to the number of BSRs traced on the analog records as compared to earlier surveys.

Jan 1, 2005

By Tina Schneider

Scientists show that polymetallic nodules and massive sulfides from deep sea mining contain valuable metals. These metals have the potential to overcome future shortages of supply. Hence, companies, government agencies and industrial associations increasingly evaluate deep sea mining as a promising supplement of land mining. Technologies to extract, exploit, transport and smelt polymetallic nodules and massive sulfides industrially are still in conceptual stage and not sufficiently advanced for operation. According to the International Seabed Authority, large scale exploitation would require a successful pilot mining test in order to demonstrate e.g. the technological feasibility but also the conservation of environmental systems services. At the same time, NGO´s and a some scientists point out that large scale extraction of polymetallic nodules and massive sulfides could disturb the habitat of benthic organisms, with unknown long-term effects. Aside from the direct impacts of mining, indirect consequences about leakage are likely. In the oral presentation I will show how companies, government agencies, scientists and association/interest groups perceive and assess economical/technological, social and environmental risks and opportunities of deep sea mining. In order to analyze the perspectives of each stakeholder group on deep sea mining, we conducted 15 interviews with four stakeholder groups and a large scale survey (n = 500, return rate = 13 %) in Germany. We used the concept of sustainability with its economical/technological, ecological and social dimensions for the interpretation of the results. The empirical research shows the following core results:

Jan 1, 2018

By Irina Melekestseva

The Cu-Zn massive sulfides from the basalt-hosted Semenov-2 hydrothermal field (13°31.13´ N, 44°59.03´ W, MAR) are enriched in Au (22?188 ppm) and Ag (127?1787 ppm) [Ivanov et al., 2008] and elevated contents (ppm) of Se (269?289), Sn (123?125), and Sb (72?75). These may indicate heterogeneous substrate rocks and possible ultramafic rocks. Based on phase analysis, 70% of the gold in the massive sulfides is free. LA-ICPMS analysis has shown that the main carrier of the invisible gold is covellite (22.51? 226.64 ppm). Covellite is also characterized by elevated contents of Se, Mo, Sn, Te, Au, Bi, As, Ag, Sb, Tl, and Pb relative to the primary sulfides.

Sep 14, 2011

By Philomene Verlaan

Analysis of the relationship between environmental parameters and the content of Mn, Ni, Co, Cu, Fe and Zn in ferromanganese crusts permits improved identification of locations to prospect for crusts with commercially valuable concentrations of these metals. In this study we asked whether a statistically significant relationship exists between primary productivity of the overlying surface waters, the concentration of O2 in and depth of the O2 minimum layer on the metal content of non-hydrothermal ferromanganese crusts in the Pacific Ocean between 130o W and 175o E and 0o to 30o S (the study area). To further develop the interpretation of the results of the statistical analysis and to assess in detail the geographical expression of these parameters in terms of metal content in crusts, a geostatistical technique (kriging) was used to generate contoured values for metal content, primary productivity and O2 concentration in and depth of the O2 minimum layer in the study area.

Jan 1, 2001

By Kaihui Yang

Volcanogenic massive sulfide deposits are generally considered to have been formed by hydrothermal fluids that leach ore metals out of footwall rocks. However, the necessity for a metal-rich magmatic component in the ore-forming fluid of "giant" ore deposits has been debated over the decades. The solution to this issue is important not only for metallogenic models but also for the mineral exploration. In the hydrothermal leaching model, massive sulfides at mid-ocean ridges are deposited from hydrothermal fluids containing 80 ppm Fe, 6 ppm Zn, 2 ppm Cu, 350oC, and 0.7 g/cm3 density (average data for 21oN East Pacific Rise). A simple calculation demonstrates that such a dilute fluid is unlikely to have been responsible for the formation of the largest ancient massive sulfide ores of greater than 100x106 tonnes, such as Kidd Creek, Brunswick No. 12, Neves Corvo, and Rio Tinto. For such a deposit consisting primarily of pyrite, sphalerite, galena and chalcopyrite (other minerals, including gangue, might account for an additional 10-20%) and even assuming 100% precipitation and retention of the sulfides, more than 790 km3 of vent fluid would be required. For typical water-rock reaction ratios of about 2, this fluid would have to have reacted with about 395 km3 of rock to acquire its metals by conventional leaching processes. This estimate, however, conflicts with the observation that even a giant massive sulfide ore body is usually underlain only by a few cube kilometers of obviously altered rocks. Moreover, this model is not consistent with the observation of hanging wall alteration in many large massive sulfide deposits. The close spatial association between massive sulfides and volcanic rocks, in both ancient and modern sea floors, suggests that direct magmatic contribution should be taken into account in the genetic model. Magmatic fluids, capable of carrying abundant ore metals and volatiles and escaping from magma by depressurization, are well known from modern active volcanoes on land. High concentrations of metals occur in CO2-rich magmatic fluid trapped in felsic volcanic rocks nearby large presently-forming VMS deposits in the eastern Manus Basin (Pacmanus, Suzette) and also in the footwall rocks of Ordovician giant Brunswick #12 deposit in the Bathurst district, New Brunswick. Only 1% of such metal-rich magmatic fluid mixed with heated sea water, that has leached its metals from rocks, would contribute 85% of the total metals to form an orebody. Such magmatic fluids are most likely to be formed from volatile-rich felsic magmas that are prevalent in back arcs, and, if added to the normal circulation system, the fluids could be responsible for the formation of "giant" ore deposits. If this is true, then the study of magmatic fluids in the seafloor volcanic rocks may provide criteria for the exploration of large ore deposits.

Jan 1, 2011

By B. J. Bluck

Diamond mega-placers, in order to rank amongst the primary diamond deposits, are defined as => 70 m carats at =>95% gem quality. There is only one mega-placer known and that is found along the coast of southwestern Africa fringing the Kaapvaal craton. Placers are classified as residual when they are left on the craton, transient when being eroded into the exit drainage and terminal. Terminal placers, in being the final depositories of diamonds off the craton, have the greatest probability of being a mega-placer and such is the case in the placer deposits near the Orange River mouth, southwestern Africa. There are four main groups of conditions leading to the development of a mega-placer: the craton, the drainage, the nature of the environment at the terminus and the timing. The craton, in its role as the producer of diamonds is significant in respect to its size, diamond-fertility, the degree to which diamonds from successive kimberlite intrusions have been retained there and their availability to the final drainage yielding the mega-placer. Cratons in being buoyant have a tendency to leak diamonds into surrounding basins but in being incompressible often have orogens converge onto them resulting in lost sediment being returned as foreland basin fills. In order to concentrate a bulk of diamonds the drainage basin has to be large with a high proportion of it on the craton. The drainage yielding the mega-placer should ideally not have been preceded by older drainage and other systems that may have robbed the craton of earlier diamonds. The exits of diamonds from the craton need to be few in order to focus on their supply and the drainage network needs to be efficient in order to remove the maximum volume of diamonds off the craton. This efficiency and the focused termination is best achieved by the rejuvenation of a pre-existing drainage network. The drainage should be young enough to yield host sediments friable enough to allow brittle diamonds to be recovered from them.

Jan 1, 2004

By Fernando J. A. S. Barriga

Exploration for active seafloor hydrothermal vent fields has been highly successful, and more than 300 such fields have been discovered to date. Some will most probably be mined, given their high metal grades (Cu, Zn, Au and others). However, the current practice detects active systems, and activity rates, not the size of the deposits. This strategy may leave undetected some of the best targets, for several reasons as follows: 1. Large hydrothermal plumes are a measure of dispersion of ore components, not of efficiency in the generation of orebodies; 2. Deposits formed a few hundred years (or more) before present will generally have ceased their activity and will not be detected by plume studies; 3. Deposits formed under a cover rock (up to a few meters of sediments, volcaniclastics, or the like) may exhibit only minor seafloor hydrothermal activity, possibly diffuse flow. Cover rocks will often host hanging wall rock alteration, expressed in geochemical and mineralogical haloes. It has been demonstrated in many instances, especially for deposits formed in the geological past, now exposed on land, that ore genesis under a cover rock is one of the most suitable processes for generating large massive sulfide deposits. One of the great challenges for submarine resource knowledge will be to develop adequate exploration strategies for sizeable orebodies, not necessarily hydrothermal vent fields, sometimes hidden under a cover rock.

Jan 1, 2011

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By Tetsuo Yamazaki

Manganese nodules on deep ocean floors have continuously received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and relatively higher metal concentrations (Mero, 1965; Cronan, 1980). Several registered Pioneer Investors have already identified promising sites in deep-sea regions for manganese nodule mining (ISA, 1998), and appropriate mining technologies have been developed during the last thirty years by the international consortium and several nations (Welling, 1981; Kaufman et al., 1985; Bath, 1989; Charles et al., 1990; Yang and Wang, 1997; Yamada and Yamazaki, 1998; Hong and Kim, 1999; Muthunayagam and Das, 1999). The mining feasibility for manganese nodules, including an economic evaluation, has been examined in detail by some researchers (Andrews et al., 1983; Hillman and Gosling, 1985; Charles et al., 1990; Soreide et al., 2001).

Jan 1, 2011

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991