Search Documents

By William Siapno

Manganese nodules, as metal ores, have for the most part been cast aside from further consideration within this century. However, in the decade of the 90s, rising demand at all levels of society, for clean air give nodules a new - lease on life as a stack gas cleaning agent. Further, the Clean Air act of 1990, mandates enormous outlays to bring systems into compliance with new stringent standards. Quick corrective actions are imperative. Research beginning in the 1960s proved nodules possess unique qualities to remove acid compounds from stack gases. Early this year, the National Science Foundation awarded General Electric an $83 million contract to design a system to extract oxides of sulfur and nitrogen from coal fired power plants. Environmental damage is abundantly evident on the ground, from the air as well as form space. A dirty pall of yellow-brown smog is smothering both animal as well as plant life around the globe. Losses run into billions!

Jan 1, 1991

By Carl L. Kaiser

This abstract discusses selected recent technology developments at the Deep Submergence Lab at the Woods Hole Oceanographic Institution aimed at fundamentally changing the nature and scope of AUV operations in the deep ocean. The Autonomous Underwater Vehicle (AUV) Sentry is described in its current configuration with discussion of emerging capabilities. Telepresence enhanced AUV operations are discussed including moving both operations and data processing personnel off the vessel. Autonomous Surface Vessel (ASV) aided AUV operations are discussed including recent experiments where an ASV provided both navigational aiding and a satellite based relay for acoustic communication of telemetery and mission redirection. New flexible communications strategies to perform intervention and manipulation tasks from an untethered vehicle are discussed. The abstract concludes with a brief discussion of industrial collaborations, including the newly launched Center for Marine Robotics.

Sep 14, 2011

By Mayumi Ito

Seafloor hydrothermal deposits are found worldwide at 700 to 3,600 meters below sea level [1] and contain base and precious metals like Cu, Pb, Zn, Au, and Ag. Some deposits were found in the Japanese exclusive economic zone and the commercial potential will depend on developments in mining and treatment costs of onshore mines. The ores require mineral processing to become concentrate for the various metal smelters and the authors are investigating mineral processing treatments of collected samples. The collected samples were classified into three components (chimney, mounds, and substrate rocks) and they were separated using a RETAC jig. The mound component contains zinc, lead, and copper minerals and further separation using flotation was investigated. This paper introduces results of the mineral processing tests using gravity separation and flotation.

Jan 1, 2011

By A. M. Olivarez

The elucidation of the theory of plate tectonics has provided a conceptual framework for understanding the formation and distribution of different types of ore deposits. For example, we now recognize that certain kinds of mineral deposits are generally associated with a particular type of plate boundary (i.e., massive sulfides often occur along divergent plate boundaries, whereas porphyry copper deposits are typically found along convergent boundaries). During certain geologic time periods, plate reorganization events have changed the relative proportion of different types of plate boundaries. Corresponding changes have been observed in the abundance and distribution of ores deposited during these times. The present study examines the temporal aspects of this relationship; i.e., do plate reorganization events play an active or passive role in ore formation? In other words, do plate reorganizations simply provide a more favorable tectonic setting in which ore formation can occur over significant time periods, or are they directly linked to the mineralization process? We have examined this question by comparing regional tectonic histories with the ages of known massive sulfide and porphyry copper deposits. Because these deposits, in particular massive sulfides, form as a result of hydrothermal activity, we have also compared regional tectonic histories with proxy indicators of this process in the marine sedimentary record. These indicators include increased mass accumulation rates of Ca, Fe, Mn, and opal, characteristic changes in the Sr/Ca and Mg/Ca ratios of biogenous carbonates, and shoaling of the carbonate compenstion

Jan 1, 1988

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011

By Jae-Hyung Park

Since the Industrial Revolution, the land resources have been decreased rapidly as the industrialization. And this phenomenon brings to our mind an interest in deep-sea resource(manganese nodule). Hence, Korea has been participated in the development project of exploiting manganese nodule since 1983. Hwang and cho(1998) studied the economic efficiency evaluation of manganese nodule carrier. But they used the TAMU(Texas A&M University) model, and assumed deadweight and velocity of bulk-carrier. If we use some optimization technique, more economic manganese nodule carrier can be selected and evaluated without limited assumption. In this study, we evaluated the economic efficiency of manganese nodule carrier using genetic algorithms(GAs).

Jan 1, 2003

By Robert M. Owen

The reconstruction of ocean history has been a major focus of marine research over the past decade. A significant outcome of these investigations is the recognition that certain types of marine mineral deposits are linked to regional to global scale changes in ocean composition and climate conditions. Manganese-bearing deposits are of particular interest in this regard because changes in their occurrence, distribution and/or composition are responsive to both biochemical and geological factors. Analyses of such deposits whose formation spans critical age/epoch boundaries thus provide clues concerning the interplay of different process during anomalous periods in Earth history. Recent studies demonstrating this deposit - event - process relationship include: (1) Changes in the bulk chemical composition of ferromanganese crusts during the Late Miocene-Early-Pliocene (-7-3 Ma) that coincide with a period of enhanced biological productivity in the eastern equatorial Pacific upwelling zone; (2) The formation of large statiform manganese deposits at the Cenornanian- Turonian Boundary (-92 Ma) in association with widespread oceanic anoxia; and (3) Increased deposition of hydrothermal precipitates caused by tectonic reorganizations at the Paleocene - Eocene boundary (-55 Ma) that resulted in global-scale changes in atmospheric and oceanic circulation and climate.

Jan 1, 1995

By Peter M. Bartlett

The Republic of South Africa ranks among the world leaders in both reserves and production of numerous land-based mineral commodities. Over the last three decades, however, South Africa has also identified several commodities that may exist in commercial quantities in the marine environment. The major targets include 1) placer diamonds; 2) titanium- and zirconium-rich beach sands; 3) sedimentary and concretionary phosphorite and glauconite deposits; 4) manganese nodules; and 5) hydrocarbons. South Africa ranks second in world reserves of diamonds and has potentially enormous sea resources. Diamonds are currently recovered on the Atlantic side from ancient beach gravels in the Northwest Cape Province and from the seabed south of the Orange River to Lamberts Bay. Approximately 100,000 carats (or just 1% of South Africa's total annual production) are produced each year from offshore operations. DeBeers is investing approximately $5 million per year on sea prospecting activities and currently operates three vessels in offshore recovery operations. Diamonds recovered at sea will remain a small percentage of total production because of huge land-based reserves that are mined at a fraction of the cost of seabed operations.

Jan 1, 1986

By Amy Gartman

"Seafloor hydrothermal systems result in the emission of abundant particles and nanoparticles into seawater1. Many of the elements in these particles settle locally, although some are transported distally to the global ocean2. Although broad similarities exist, the mineralogy, size and therefore reactivity of particles emitted varies between sites in the global ocean, and even within sites at the same vent field. The particle geochemistry of these vent fields is a critical but little understood component both from a perspective of baseline characterization and potential environmental impacts.The mining of seafloor massive sulfides formed from hydrothermal venting will generate a new class of particulates in the deep ocean. Broadly, black smoke and SMS tailings exhibit similarities including abundant Cu, Fe and Zn sulfides, and a large number of submicron particles. In addition to the major minerals, minor minerals including As, Bi, and Pb are present, especially in back arc settings. However despite broad similarities, natural “black smoke” and crushed sulfides created during mining operations differ significantly in size class, morphology, abundance, and reactivity. A comparison of these two classes of particulates will be presented, including chemical composition and reactivity to dissolution and oxidation."

Jan 1, 2017

By Carlos Almeida, Bruno Matias, Stef Kapuskiak, Eduardo Silva, José Miguel Almeida, Alfredo Martins

Underwater intervention operations have been supported by robotic systems such as remotely operated vehicles (ROV) for a long time. In particular challenging scenarios such as the deep sea, the use of ROV systems for environment awareness is in fact the main tool of choice. With the technical advances in autonomous robotics, there is an increased effort in substitute ROVs whenever possible for autonomous underwater vehicles (AUV). These systems don't have tether and thus provide large advantages from the operations and logistic point of view. However the limited options for underwater communications render them impracticable for many tasks were real time environment awareness and direct human control is needed. Emerging applications in underwater mining, both at sea [1] and in inland flooded mines [2] pose additional requirements in terms of operation support needs and environment restrictions. Two main tasks are to be addressed by assisting robots in these underwater mining operations: providing adequate environment awareness for human operators and obtain precise realtime 3D environment modelling (particularly relevant for the mining planning). The use of ROVs with umbilical cable, has in this case large limitations due to the nature of the mining cutting (performed by dedicated systems) that limit manoeuvrability and pose high risk of cutting the cable or damaging the vehicle. In this paper we present EVA (Exploration VAMOS AUV) an innovative hybrid ROV/AUV system developed for operations support in inland underwater mining operations. This robot is always operated without tether, and the can be used in a wireless ROV tele-operation mode using very short range high bandwidth underwater communication systems and in autonomous AUV mode.

Jan 1, 2018

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Pavel Mikhailik

INTRODUCTION Ferromanganese (FeMn) crusts from Mendeleev Ridge, Chukchi Borderland, and Alpha Ridge, in the Amerasia Basin, Arctic Ocean, are similar based on morphology and chemical composition. The crusts are characterized by two- to four-layered stratigraphy. The chemical composition of the Arctic crusts differs significantly from hydrogenetic crusts from the North Pacific Prime Zone (PCZ; Hein et al., 2013), such as a high mean Fe/Mn ratio (2.6 versus 1.3) and low Si/Al ratio (1.8 versus 4.0), with lower Mn, Ca, Ti, P, Ba, Co, Cu, Ni, Pb, Sr, and Zn and higher Si, Al, Mg, As, Li, V, Sc, and Th. Based on Arctic FeMn crust mineralogy, chemical composition, and growth rates, crust formation was dominated by three processes: Precipitation of Fe-Mn (oxyhydr)oxides from ambient ocean water, sorption of metals by the Fe and Mn phases, and fluctuating but large inputs of terrigenous debris (Konstantinova et al., 2017; Hein et al., 2017). The Mn and Fe phases are hydrogenous and reflect bottom ocean-water chemistry and the aluminosilicate phase contains stable detrital minerals such as quartz, feldspars, zircon, monazite, and clay minerals. A precise method of studying the distribution of elements in FeMn crust phases is sequential leaching that dissolves four mineral phases of different stability step-by-step, in the following order: easily leachable phase, mostly bio-calcite; manganese oxides; iron oxyhydroxides; and residual aluminosilicate minerals (Koschinsky and Halbach, 1995). Twelve bulk crusts and crust layer samples obtained from six hydrogenous FeMn crusts were studied. Those crusts were collected during Russian (Arktika 2012) and USA (HLY0805, HLY0905, and HLY1202) research cruises from different parts of the Amerasia Basin (Mendeleev and Alpha Ridges, Chukchi Borderland). Samples were chosen for the sequential leaching experiments based on their morphology, location, and water depth. Hydrogenetic crust (D07-33) from the Tuvalu EEZ, central-west Pacific Ocean, was included in the experiment for comparison. Recovery during the four-step sequential leaching, with respect to the bulk analyses, was between 80% and 120%.

Jan 1, 2018

By J. W. Jamieson

INTRODUCTION Hydrothermal vents that form seafloor massive sulfide (SMS) deposits represent unique biodiversity hotspots that host many species that are found only at these sites. The destruction of these habitats remains one of the greatest environmental risks associated with proposed mining of SMS deposits. For this reason, there is a growing movement to protect active vent sites from direct and indirect effects of seafloor mining (Van Dover et al., 2018). Mitigating the adverse effects of mining on these ecosystems may prove to be one of the greatest challenges facing the marine minerals industry. At the same time, there is increasing evidence that inactive or extinct hydrothermal systems, which do not host the density or diversity of animals typical of active vents, may constitute a significant proportion of the SMS resource potential on the seafloor. Mining inactive SMS deposits may therefore present an extractive opportunity that does not necessitate the disturbance or destruction of active vent habitats. However, if mining of SMS deposits is to take place only at inactive vent sites in order to protect active vent ecosystems, a clear definition of what defines a site as active or inactive is necessary. ACTIVE AND INACTIVE SEAFLOOR MASSIVE SULFIDE DEPOSITS Our understanding of the number of inactive deposits, their size and grades, and how they are preserved on the seafloor remains limited, largely due to the challenges associated with finding these deposits. Over 90% of all hydrothermal vent fields discovered so far are hydrothermally-active. Almost all of these sites were discovered through the detection of chemical anomalies associated with active hydrothermal venting via water column surveys. Inactive sites have no associated hydrothermal plume, and thus the well- established plume survey exploration method is not effective. As a result, very few truly inactive sites inactive sites have been discovered. Alternative exploration methods, such as spontaneous potential (SP) surveys, magnetic surveys, and high-resolution mapping are required (Cherkashev et al., 2013; Jamieson et al., 2014; Tivey and Johnson, 2002). As methods for locating inactive deposits continue to develop, our understanding of the distribution and resource potential of these deposits will increase, and the focus of resource exploration will shift from active to inactive vent sites. However, for now, most exploration and deposit development activities remain focused on active vent fields.

Jan 1, 2018

By Chris Roper

The Gavia Autonomous Underwater Vehicle is a two-man portable AUV that is capable of performing seafloor surveys in water depths to 2000 meters. The standard survey sensor suite includes a dual frequency side scan sonar and high resolution digital camera. Additional survey sensors are currently being incorporated into the Gavia AUV, include Sub Bottom sonar, Swath Bathymetry sonar and Multi Beam sonar. The modular design of the Gavia AUV allows the end user to quickly incorporate new sensors including client developed propriety sensors.

Jan 1, 2005

By G. A. Gross

Technological development in the last two decades has provided access to the deep seabed and opened a new frontier for exploration. Interest in Canada has focused mainly on study of metallic mineral occurrences and the development of a scientific data base and technology for identification and appraisal of potential mineral resources. Canadian industry and government have played an active part in the assessment of manganese nodule resource potential and the possible impact that development of these resources might have in the world mineral markets.

Jan 1, 1985

By Geir Johnsen

Hyperspectral remote sensing has been used extensively on land to identify minerals for the mining industries. An underwater hyperspectral imager (UHI) has been developed at the Norwegian University of Science and Technology. It captures optical fingerprints within the spectral range of 400-700 nanometers, with 1 nm resolution. The UHI has been tested on nodules and SMS deposits in the laboratory and on the sea floor to establish if this technology can be used to identify marine mineral deposits, to determine type of deposit and distribution.

Jan 1, 2010

By Daniel E. Walsh

The recovery of most minerals, which are amenable to gravity concentration, is standardly determined by accurate sampling and assaying. .With respect to particulate - gold ores, sampling and assaying are still the convention, but the accuracy and reproducibility of these operations are much discussed and debated points. Evaluation of gravity concentrators by conventional sampling and assaying techniques is very time consuming, costly and may introduce a large amount of uncertainty into the results due to the particulate nature of placer gold. These problems are not unique to placer gold ores and apply to any low grade ore with particulate values. A gravity concentrator evaluation process developed by MIRL employs the use of neutron activated gold (198Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems. Beginning in 1984, MIRL conducted radiotracer studies of unit processes, which included jigging, static wedge wire screening, elutriation, and concentration with compound water cyclones.

Jan 1, 1989

By Henk van Muijen

From an interesting and intriguing scientific research topic, deep sea mining has altered into an interesting mining prospect over the last years. Ten years ago most of the focus was on geological investigations, searching for typical deep sea deposits and getting answers on where we can find them and how these deposits were formed. At this moment we know much more about the interesting deposit possibilities and with our quest for minerals, metals and other materials to feed global economic growth, answers as to the technical and economic feasibility to mine these deposits are sought. This is not a new phenomenon as we already witnessed such question late 1970?s and early 1980?s. Most of the focus was on mining manganese nodules and brines in the Red Sea driven by the report of the Club of Rome that predicted shortages in near future at that time. Development went different, but later in the 1990?s a rival of interest could be noticed for mining deep sea deposits.

Jan 1, 2010

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By A. A. Schipaanboord, S. J. Dasselaar

"With the growing global demand for strategic metals, commodity prices are rising and the scarcity of some metals is increasing. Europe’s technology sector is also affected by this growing shortage of metals. Securing the supply of critical metals is now a major element in Europe’s economic strategy. The Blue Mining and Blue Nodules projects have been initiated to principally advance deep sea mining technology beyond current TRL-levels.These critical metals are found inside so-called “polymetallic nodules”, lying on the seafloor in deep-sea environment. These nodules have a typical abundance of 10-25 kg/m2 and a size range of 10-125 mm.Harvesting the polymetallic nodules is challenging. Two main methods of harvesting or collector equipment are distinguished: hydraulic and mechanical. Over the last year, Royal IHC has designed, build and tested a full-scale hydraulic collector. Meanwhile, a mechanical collector is being developed.First, a scaled version of the hydraulic collector was developed and tested in order to have a proof of principle. The development as well as optimization were aided by multiphase CFD simulations."

Jan 1, 2017

By Colin Devey

As marine research scientists we especially appreciate the uniqueness and complexity of the deep-sea hydrothermal vent fauna and environments, and are particularly interested in preserving vents for their scientific, aesthetic, ecological, and potential economic values. In fact, because of the specialized nature of the equipment required to work at deep-sea hydrothermal vents, such as occupied and unoccupied research submersibles, scientists are the primary group of people who have the opportunity to visit these extraordinary environments. The potential for significant impact of scientific activities on a single vent site or a population of vent animals pales in comparison to the potential for disturbance by volcanic/tectonic events or industrial mining/harvesting activities. Nonetheless, we recognize that some scientific activities could adversely affect individual sites or impact communities more than is necessary, if research activities are not carefully planned and executed. In addition, because only a limited number of sites are currently known and scientists from a wide variety of disciplines frequently work at single locations, we recognize the potential for use conflicts among scientists, at sites where scientific activity is intense.

Aug 24, 2006