Search Documents

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By James R. Hein

Manganese nodules from the Cook Islands (CI) Exclusive Economic Zone (EEZ) are compositionally different from other nodule fields. CI nodules have relatively high cobalt concentrations and low nickel, copper, and manganese concentrations (e.g. Hein and Petersen, 2013). This reflects the predominantly hydrogenetic (seawater source) origin for metals in the CI nodules versus dual seawater-pore water sources for most other nodules. The concentrations of many critical and strategic metals have not been previously analyzed for CI nodules, so comparisons with other nodule fields have been limited. To address this, we analyzed a set of nodules distributed throughout the CI EEZ for a complete set of 67 elements, including all of the metals that may be of economic interest, such as the rare earth elements (REEs), yttrium, tellurium, niobium, zirconium, tungsten, titanium, and others (see selected elements in Table 1). In addition, we recalculated the tonnages of nodules and contained metals from nodule abundance areas (in square kilometers) determined by GIS ArcMap calculations based on JICA/MMAJ (2001) nodule distributions. The nodule tonnage calculated and summed from each abundance sector yields a total inferred resource estimate of 9.66 billion tonnes of nodules covering an area of 1.21 million square kilometers; using a cut-off of 6 kilograms of nodules per square meter, yields a median tonnage of 8.59 billion tonnes of nodules covering 687,647 square kilometers (Table 2).

Sep 14, 2011

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By Richard Harrison, Frank Lim

Deepsea Mining will soon become a reality with Nautilus Minerals getting their equipment ready to mine SMS at Solwara 1 off the coast of Papua New Guinea. The vertical transport system (VTS) adopted by Nautilus consists of a riser hanging ‘freely’ from the mining production vessel with a lifting pump unit suspended at its lower end. A compliant jumper connects the pump to the seabed crawler without restraining its movements. In this free-hanging VTS arrangement, the vessel can be re-positioned to follow the crawler should it want to extend the mining area and start stretching the jumper. A recently proposed alternative to this is a free-standing VTS whereby the riser is grounded on the seabed with a base and maintained in an upright position by distributed buoyancy modules or a buoyancy tank at the top. A compliant jumper connects the seabed crawler to the riser base, and another connects the riser top to the vessel. In this free-standing arrangement, the entire VTS can be lifted clear of the seabed for relocation to a new mining area. This paper will describe the important features of the two options and discuss the advantages and disadvantages in respect of riser dynamic behavior, water depth, weather and mining windows, pump maintenance, installation and retrieval, continency measures, etc. The two systems will also be appraised separately for mining SMS and SMnN deposits.

Jan 1, 2018

By Robert G. Paul

President Reagan's Exclusive Economic Zone (EEZ) Proclamation of March 10, 1983, extended United States ocean jurisdiction 200 nautical miles offshore our coastal states and territories. The accompanying policy statement noted that this action was a result of recently discovered deposits of polymetallic sulfides and cobalt-rich manganese crusts, which could be a major source of minerals important to the U.S. economy and security. Within these 3 billion acres of exclusive economic jurisdiction, the United States has sovereign rights to explore, develop, conserve, and manage the mineral and other natural resources of the seabed. The President has directed the Department of the Interior (DOI) to encourage exploration and production of minerals from this area. The DOI, through the Minerals Managment Service (MMS), is responding to this presidential directive by developing a leasing program for nonenergy minerals in the EEZ. The authority to develop this leasing program is the Outer Continental Shelf Lands Act of 1953, as amended in 1978, which authorizes the Secretary of the Interior to grant leases for oil, gas, sulfur, and other mineral resources on the Outer Continental Shelf (OCS). The Solicitor of D01 has determined that the definition of the OCS for legal purposes extends at least 200 nautical miles offshore of our coastal states to the EEZ boundary. Section 8 (k) of the Act allows the Secretary to lease minerals, other than oil, gas, and sulfur, on the basis of competitive bonus bidding and under such terms and conditions as he may prescribe at the time of offering the area for lease.

Jan 1, 1985

By David Heydon

The big money is backing both manganese nodules and manganese crusts as the most likely deep ocean mining development by 2010, but seafloor massive sulphides of copper/gold/zinc offer an alternative bet for a start-up by 2010. A study of the ?form guide? or comparison of these resources provides direction on which resources are economic candidates for commercial deep ocean mining development by 2010. This paper covers the commercial and technical issues of exploration, resource definition, drilling/sampling, sea bed mining options, mine plans, environmental issues, legal tenure and capital and operating costs (i.e., profitability) of these two mineral types. Nautilus Minerals has just completed a pre-feasibility engineering study of mining sea floor massive copper/gold/zinc sulphides at 2,000 m depth. The Nautilus study reviewed a range of mining and lifting options, settling on tracked continuous drum cutter miners to produce 2 million tons per annum of high grade ore. Capital costs are shown to be at least 30% lower than a land based copper mine of the same production capacity. Likewise 75% of world?s copper would be produced at a higher operating cost that the proposed seafloor mine. This paper then draws on the Nautilus study for comparison with earlier feasibility studies by others on manganese nodule mining to predict the likely directions in deep ocean mining to 2010.

Jan 1, 2004

By Richard H. T. Garnett

Marine mining on the continental shelf was first attempted in 1900 for gold off the beaches of Nome, Alaska. Attempts continued until 1990 with cutter-suction, airlift and bucket-ladder dredges. Offshore Thailand profitable production of tin resulted from clamshell, bucket-ladder and trailing suction hopper dredges. Today in Indonesia numerous bucket-ladder dredges continue to mine tin. Off the coast of Namibia and South Africa nearly a dozen large and medium sized vessels are engaged in diamond production. The obvious risk results from the working environment. Vessels and lives have been lost in the past. At best the availability of mining equipment is reduced. Leaving aside the marketing and financing aspects, otherwise the most important risks are technical. They manifest themselves as diamond production short-falls with obvious financial consequences. Bias and deficiencies in sampling equipment and procedures may result in misleading grade estimates, even serious under-estimation. Inadequate sampling in terms of sample support and density may result in over-optimistic grade determinations, especially if under-sized mining blocks are outlined. Quantitative measurement of the geotechnical characteristics of the sediments to be mined is an essential stage in a feasibility study. Without a full understanding of the bedrock profile and the overlying sediments the ease, completeness and speed of excavation during the mining process cannot be properly estimated. Both historically and at present the greatest negative discrepancies from production estimates result, not from grade shortfalls, but from significantly lower mining rates than thought possible by the operators. The learning curve in marine, production mining is steeper and longer than is generally recognised by newcomers to the industry. Examples are provided from tin, gold and diamond mining experiences.

Jan 1, 1998

Massive sulfides discovered in 1991 and further explored in 1993 in the eastern Manus back-arc basin, north of Papua New Guinea, represent one of the few modem seafloor occurrences known to he associated solely with highly siliceous volcanic rocks. As such they are very close analogs of ancient volcanogenic massive sulfide (VMS) ore deposits, and hence an excellent natural laboratory for developing new approaches for land-based VMS exploration. The Manus Basin lies between the active New Britain subduction zone and volcanic arc to its south and the opposed inactive Manus subduction trench to its north. It is being extended in a complex pattern of short neovolcanic zones and oblique transform faults. In its western sector, relatively mature back-arc spreading has created predominantly basaltic segments with characteristics and mineralization generally similar to those of mid- ocean ridges. At its far east, however, the basin is distinctly immature. The East Manus Volcanic Zone lies between two members of the Manus transform set, and is an en-echelon series of neovolcanic edifices constructed on extensionally thinned island arc crust formed during the earlier manus subduction episode. Individual edifices range from predominantly basaltic to predominantly dacitic in composition. Two of the edifices are known to be hydrothermally active, and a particulate plume with unknown source occurs in the seawater column above a third.

Jan 1, 1993

By Christina Pomee, John Parianos

"TOML’s ISA Contract comprises six areas (A-F) that span from 118° to 152° W and from 7° to 15° N or over 70% of the CCZ.During a 2015 exploration cruise, TOML scientists found that the a logging system developed by ISA (2010) was able to be adapted and enhanced, to describe in some detail the varied morphology of nodules both within the TOML areas and between them.The shapes and sizes of nodules seen were then found to relate to substrate type and setting, and thus likely thickness and long-term stability of the geochemically active layer. Consideration of the various processes that might influence growth helps constrain nodule formation further. The nodules effectively record the long-term geochemical conditions that lead to their formation.ISA (International Seabed Authority), 2010. A Geological Model of Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone and Prospector’s Guide for Polymetallic Nodule Deposits in the Clarion-Clipperton Fracture Zone. International Seabed Authority Technical Study: No. 6 ISBN: 978-976-95268-2-2"

Jan 1, 2017

By Mark Vardy, Kasia-Leigh Chidlow, Tim Minshull, Jeorg Bialas, Sven Peterson, Bramley Murton, Alba Gil

Since the discovery of the first black smoker on the East Pacific Rise in 1977 (Francheteau, et al., 1979), the hydrothermal vents, now called seafloor massive sulphides (SMS) deposits, have generated great interest in the geological community, especially regarding their formation and composition. SMS deposits are areas of hard substratum, with high base metal and sulphides content, that form through hydrothermal circulation and are commonly found at hydrothermal vent sites. The high base metal (Fe, Cu, Zn, Pb), sulphur-rich mineral content has interested mining companies, due to their potentially high economic value. Currently, the known SMS deposits do not have the same dimensions as the massive sulphides (MS) found on land (covering just 10s to 100s m2) and pose significant mining challenges (being located in water depths between 800 m and 6000 m), meaning that they do not appear to be economically exploitable at present. However, these deep-sea mineral resources could be important targets in the near future, particularly with our ever-increasing demand for base metals. A key aim of the European Union-funded Blue Mining project is to develop techniques to robustly quantify SMS deposits dimensions (both surface expression and subsurface extent) and therefore assessing the suitability of SMS deposits for future economically viable and environmentally clean deep-sea mining operations.

Jan 1, 2017

The Brothers hydrothermal system is host to two very contrasting vent fields and to date, is the only known example of this kind for any submarine arc volcano in the world. Firstly, there is the NW caldera field. It is perched on the caldera walls and is up to 1,200 years old, and represents a more ?mature? system dominated by water/rock interactions, though there is also evidence for magmatic contributions to the hydrothermal fluids. It is host to relatively high temperature (~300°C), focused venting of metal-rich fluids. Large Cu- and Zn-rich sulfide chimneys occur at this site, with high concentrations (up to 90 ppm) Au apparent in some chimneys. Vent fluids of the NW caldera site show sub-seafloor phase separation is occurring at this site. Silica concentrations in these vent fluids are consistent with the vent fluid temperatures. Secondly, there is the cone vent field that is much younger, and which sits atop the summits of a main cone (the Upper cone) and an adjacent satellite cone (the Lower cone) that occur inside the caldera, near the southern caldera walls. This field is dominated by S-rich vents with vent fluids more diffuse, lower in temperature (<120°C), very gassy and acidic (to pH 1.9), and relatively metal-poor. Fluids of the cone site have Mg and SO4 concentrations higher than seawater values, indicating these ions have been added to the hydrothermal fluid and are not being depleted via normal water/rock interactions. Variability occurs between the two cone vent fields, with the diffuse discharge observed at the Upper cone volumetrically small and chemically different from the Lower cone. For example, from the vent fluid Mn, Li, Rb, and Cs concentrations, it is apparent that the Lower cone has experienced a lower degree of water/rock interaction (i.e., more reaction) than the Upper cone. Vent fluid pH is higher for Lower cone, consistent with more reaction and neutralization of acidic gases. Fe/Mn is lower at the Lower cone due to decreased Fe solubility at the higher pH. The lowest pH sample (1.9) is from the Upper cone that has 39.4 mmol/kg of SO4, consistent with input of magmatic SO2 and disproportionation to sulfuric acid and S or H2S. Thus, the Upper cone site could be interpreted to have a shorter reaction path and residence time between the point of magmatic degassing and the seafloor venting than the Lower cone site. Isotopic compositions of the NW caldera and cone vent fluids show evidence for magmatic water with negative dD and d180 values, while 3He/4He values show the Brothers hydrothermal system has shifted towards more magmatic conditions over the past several years with both sites affected by magmatic events. Similarly, vent fluid sulfide d34S values and those for sulfide minerals from NE caldera chimneys also indicate disproportionation reactions involving magmatic SO2. Minerals such as chalcopyrite, bornite, chalcocite, covelllite and euhedral grains of hematite occurring in high temperature chimneys from the NW caldera site are consistent with a more oxidizing, magmatic fluid, while bulk sulfide geochemistry data show evidence for a higher temperature suite of elements (e,g., Mo, Co, Se) associated with Cu-rich chimneys. Gold mineralization occurs in these high temperature chimneys and is associated with the most recent deposition of high concentrations of Cu, where d34S values are most negative. Geophysical evidence suggests that the top of a magma chamber occurs ~2.5 km below the caldera floor, beneath the cone site in the SSE quadrant of the volcano. Very low velocities of <1 km-2 are seen in the seismic data between the magma and the seafloor, and are indicative of gas release. Harmonic tremor data provide evidence for a 500 m pipe-like ?conduit? located above the magma chamber (and below the cone), linking it with the overlying hydrothermal system, providing a mechanism for magma-derived metals to enter the hydrothermal system under the cone site. The NW caldera and cone sites are considered to represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members.

Jan 1, 2010

By Elisabetta Tedeschi, Razieh Nejati Fard

Deep-sea mining is in the future perspective of mining industry and it is currently in the technological development phase. The focus of this study is on the electrical power system that provides sufficient energy for the mining equipment at the seafloor, excavating Seafloor Massive Sulfide (SMS) deposits. SMS deposits usually exist at water depths between 1500 m and 4000 m. Despite the similarities of SMS deposits excavation to the open-pit terrestrial mines, more energy is required to drill and crush the ores in the hyperbaric conditions [1], which can be done whether by static trench cutters [1] or by mobile mining crawlers [2]. In addition, the ores vertical transportation by subsea pumps requires several MW electrical power that can be supplied by all-electric subsea motors or hydraulically from water injection motors located on the surface. The power requirements can be fulfilled by an offshore or subsea power network. As the SMS mines are usually in remote locations, the straightforward solution will be an isolated offshore grid mounted on a vessel or platform similar to the most of offshore Oil & Gas projects. These power systems resemble the onshore microgrids for industrial purposes operating in island mode. However, in contrast with the onshore power networks, there are space and weight limitations in offshore infrastructures, which impose the design compactness to be a priority. In addition, having a very high reliability is necessary in the design approach of the offshore projects due to the extraordinary high expenses corresponding to repair and maintenance. The other design criterion is to improve the power system efficiency in order to reduce the size of the power equipment cooling apparatus, operational costs and CO2 emissions produced by diesel/LNG onboard generators. There are a few studies considering power system distribution for seafloor mining industry. Among them, [3] has investigated the AC and DC alternatives for SMS mining in 2400 m water depth by considering Solwara 1 project scenario introduced by Nautilus Minerals Inc. [2]. In this study, a power system design tool will be presented taking into account various water depth, power consumption levels, different distribution configurations (AC and DC) and the aforementioned design criteria.

Jan 1, 2018

By Isobel Yeo, Florent Szitkar, Sven Petersen, Sebastian Graber, Meike Klischies

Technological advances and the shift towards green energies in the last decades have led to a substantial increase in the demand for metal resources. With rising political tension, and quasi-monopolistic production of some key metals, a secured supply chain cannot be guaranteed [1]. Therefore, the focus of the international research community and mining companies has expanded to the seafloor, looking for additional resources. The seafloor may have the potential to contribute significantly to a secure metal supply in the future. However, we have only investigated a fraction of our oceans in sufficient detail to assess the global resource potential. A detailed exploration of the vast seafloor is currently economically not feasible, due to its extremely time-consuming and costly nature. Seafloor massive sulfides generally form along the active plate boundaries and at active volcanoes in arc settings. However, the resources are not evenly distributed on the seafloor. Large deposits tend to be more common along slow-spreading and ultra-slow- spreading ridges that make up the majority of the global mid-ocean ridge system [2]. Therefore, it is important to establish geological models and exploration criteria in order to narrow down the permissive areas, which are likely to accommodate economically interesting deposits. Based on a detailed study of the TAG hydrothermal field in the central Atlantic Ocean, hosting a large active mound as well as several inactive mounds, we develop exploration methods and criteria to define areas of potential massive sulfide occurrences along slow-spreading sections.

Jan 1, 2018

By Wenbin Ma, Cees van Rhee, Dingena Schott

Since the concept of deep sea mining (DSM) was proposed by J. L. Mero with his book, The Mineral Resources of the Sea, in the 1960s, many research and significant developments have been implemented. However, its commercial mining process still has not yet commenced. One of the most important issues is that a sustainable DSM transport plan is difficult to determine, taking into consideration the DSM technological, economic, and environmental aspects simultaneously. The objective of this paper is to propose a method to determine the sustainable DSM transport plan utilizing a fuzzy analytic network process method, which is a typical multi-criteria decision making method (MCDM). The DSM transport plans evaluating major criteria consist of technological, economic, environmental, and social aspects with both qualitative and quantitative attributes. Different major criteria include several sub-criteria, respectively:  Technological aspect: energy consumption, proven technology, technology reliability, production rate, technology availability;  Economic aspect: gross income, capital cost, operation and maintenance cost, investment recovery period;  Environmental aspect: species disturbance variance, severity of ill effect, turbidity of ocean water, total organic carbon content, sedimentation thickness;  Social aspect: social acceptability, policy support; The weights for all evaluating criteria and sub-criteria are determined through a questionnaire survey interviewing experts at different research fields. All the transport plan candidates are ranked based on a comprehensive index. The conducted research in this paper is meaningful to promote the DSM commercialization process.

Jan 1, 2018

By Jae-Hyung Park

Since the Industrial Revolution, the land resources have been decreased rapidly as the industrialization. And this phenomenon brings to our mind an interest in deep-sea resource(manganese nodule). Hence, Korea has been participated in the development project of exploiting manganese nodule since 1983. Hwang and cho(1998) studied the economic efficiency evaluation of manganese nodule carrier. But they used the TAMU(Texas A&M University) model, and assumed deadweight and velocity of bulk-carrier. If we use some optimization technique, more economic manganese nodule carrier can be selected and evaluated without limited assumption. In this study, we evaluated the economic efficiency of manganese nodule carrier using genetic algorithms(GAs).

Jan 1, 2003

By ?. V. Kabanov

n considered operation hydraulic and kinematic circuits of deep-water installation for sampling a ground from a sea-bottom are submitted. Control by setters is made remotely from a service station with the help of a system of telemechanics. Migration of apparatus along a bottom is ensured with the help of force of a response of a jet and Archimedean force. The mathematical exposition of the device composed and computer simulation is Design parameters are defined and static performances are obtained. Operation is in a stage of manufacture of working drawings. There are patents of Russia.

Jan 1, 2005

By Akira Usui

Occurrence of hydrogenetic ferromanganese crusts has been well documented over inactive seamounts in the central and southern Pacific Ocean. It has been thus believed that the hydrogenetic crusts develop preferentially at water depths between about 800 to 2500 meters. In fact, according to the Manganese Crust Database (F. Manheim, 1988), only two occurrences are known at water depths below 5000 m out of 819 occurrences cited in the database. Unexpectedly, we found typical hydrogenetic ferromanganese crusts from deep-sea floors; 1) outcropping old volcanic basement over the Philippine Sea Plate (abandoned spreading centers and subducting old oceanic crusts) and 2) one from the slope of an abyssal hill in the Central Pacific Basin (Cretaceous deep-sea basin) at water depths ranging between 5200 to 6100 meters. We report their occurrences with submersible observations from Shinkai 6K, physical parameters (such as thickness of crusts about 2-4 cm in maximum), chemical composition, petrology of substrate, and results of Be-10 dating for some samples in comparison with typical Co-rich manganese crusts from the Central Pacific seamounts. The preliminary chemical and mineralogical analyses reveal that they are of typical hydrogenetic origin, and typical of iron-manganese oxide mineral, vernadite, slow and probably continuous growth, and lower content of Co than the Central Pacific seamount crusts. The occurrences and nature of the crusts indicate that deep-sea floors are also optimal for the growth of hydrogenetic crust even at 5000 m water depth or deeper, only if oxygenated deep waters are supplied and the sea-floor morphology keeps stable enough for significant geological time period. Additional details of chemical analyses will be prepared by November and to be shown in the conference.

Jan 1, 2001

By Peter A. Rona

Investigations of the Gorda Ridge within the proclaimed U.S. Exclusive Economic Zone off northern California and southern Oregon, and the Mid-Atlantic Ridge extending along the center of the Atlantic Ocean, have received new impetus from the discovery of hot black smokers, sizeable polymetallic massive sulfide deposits, and vent animals at the Mid-Atlantic Ridge by the NOAA VENTS Program in 1985. Prior to that time, the oceanographic community focused investigations of seafloor venting at the faster-spreading oceanic ridges of the Pacific Ocean including the East Pacific Rise, the Galapagos spreading center and the Juan de Fuca Ridge because a consensus held that the faster spreading rates at these ridges were necessary to supply the heat to drive black smoker-type venting. As the only oceanic ridge in the Pacific with slow-spreading characteristics, the Gorda Ridge is an outlier of the slow-spreading ridge system that extends through the Atlantic Ocean and western Indian Ocean comprising more than half the 55,000-kilometer-length of the globe-encircling oceanic ridge system. In response to recent discoveries at the Mid-Atlantic Ridge the oceanographic community is shifting more of its activity to investigation of hydrothermal venting and related processes at slow-spreading oceanic ridges. The discovery cruise by a team of NOAA and university scientists followed by

Jan 1, 1988

By Timothy F. McConachy

Between April 2000 and April 2002, the Commonwealth Scientific and Industrial Research Organization (CSIRO) Division of Exploration and Mining has led 6 research expeditions totalling 160 days ship time in waters of Papua New Guinea, Vanuatu, Solomon Islands, Indonesia and Australia. Five expeditions were undertaken aboard the Australian research vessel Franklin following successful competitive research proposals, and the sixth used the Indonesian vessel Baruna Jaya VIII (see Table 1). In addition, two CSIRO participants joined JOIDES Resolution for the Ocean Drilling Program Leg 193 in the Manus Basin of PNG. The major scientific objective underpinning these expeditions was to locate and study present-day seafloor and sub-seafloor hydrothermal ore-forming activity in order to develop improved methods of exploring for ancient mineral deposits on land that originally formed by similar processes. The research has been supported financially by a number of Australian-based mineral companies, by Australian international aid agencies, and by appropriation funds from CSIRO, and was conducted in collaboration with researchers from Australia, Indonesia, Portugal, New Zealand, United States of America, South Korea, and the host nations. Building upon earlier successes in the 1986-1997 PACLARK-PACMANUS programs in the Woodlark and Manus Basins of PNG, we have sought to examine a wider range of geological settings in which ancient orebodies are inferred to have formed, including both volcanic and sediment-hosted environments. We have now visited volcanic arcs, fore-arc and triple-junction related submarine volcanoes, and back arc basins associated with convergent plate margins in the SW Pacific and SE Asia, as well as conceptual Mississippi-Valley-type targets associated with warm seeps at passive margins in the Great Australian Bight (see Figure 1). Surveys ranged from northern Sulawesi via far western Bismarck volcanic arc near PNG-Indonesia border, through the eastern Manus Basin and the Tabar-Lihir-Tanga-Feni chain in PNG, the western Solomon Islands festoon, the San Cristobal arc, parts of the Vitiaz arc, to the northern and southern New Hebrides arc in the Solomons and Vanuatu.

Jan 1, 2002