Search Documents

By Øystein Sture, Kurt Aasly, Ben Snook, Sigurd A. Sørum

INTRODUCTION Efficient exploration methodologies for base metal deposits have huge benefits for future deep sea mining endeavours, and underwater hyperspectral imaging (UHI) has been variably demonstrated to have applications in the identification and characterisation of mineralisation on the seafloor for both nodules and seafloor massive sulphides (SMS) (Dumke et al., 2018 and 2017 respectively). Due to growing resource requirements (Singer, 2017), SMS deposits are considered to be increasingly significant sources of copper and zinc, as well as silver and gold. This style of mineralisation is currently occurring at active hydrothermal vents (black and white smokers) but now-inactive sites also have the potential to be large mineral deposits. As such, the development of novel methodologies to detect both on-going and extinct mineralisations are of high importance. Geological setting During the MarMine cruise (Ludvigsen et al., 2016), non-mineralised host rock, low grade ore and high grade ore grab samples (Snook et al., 2018) was collected by ROV from the Loki’s Castle deposit (Pedersen et al., 2010), located on the Mohn’s/Knipovich junction on the ultra-slow spreading Arctic Mid-Ocean Ridge (AMOR), at a depth of approximately 2300 m. This material has been characterised as part of the MarMine project (e.g. Snook et al., 2017), and, by imaging compositionally constrained material, the measured hyperspectral responses can be used to generate a library for identification of deposits on the ocean floor. UHI technology Remote sensing with hyperspectral and multispectral technologies has seen wide use in prospecting for ores and hydrocarbons on land (Van der Meer et al., 2012). Iron oxides and sulphides have low blue reflectance and high red reflectance in the visible spectrum. The ratio between these two pairs has been used in exploration for terrestrial deposits of hydrothermal origin (Sabins, 1999). This discrimination typically also includes wavelengths exceeding the visible spectrum (1.5µm – 2.5µm). These wavelengths are typically not utilised underwater because infrared wavelengths and higher are rapidly attenuated in water. However, discrimination based on the full shape of the spectral response in the visible light (350nm – 800nm) may still be possible (Bolin and Moon, 2003). Resolving the endmembers from the spectral responses requires prior knowledge about the optical properties of the materials, i.e. their reflectance. These reflectances can be obtained in a controlled environment, where the spectra of the lamps, wavelength- dependent attenuation in water and scattering of light can be accounted for (Johnsen, 2013).

Jan 1, 2018

By Alexander Malahoff

A shipboard research system capable of operating in waters of up to 2,000 m has been designed and implemented by the Hawaii Undersea Research Laboratory (HURL), University of Hawaii. It uses a remotely-operated ocean bottom survey camera system, ROV, bottom TV grab, the PISCES V submersible, and a submersible emergency recovery system aboard the 225-foot RN KA'IMIKAI-O- KANALOA. All systems are operated from the stern of the KA'IMIKAI with a mounted Caley telearm and articulated A-frame system. The system was designed for multi-purpose use of the telearm for launch and recovery of the PISCES V submersible on a lift recovery line (with or without diver assistance), or night-time operations with an electro-optical cable using either the HURL ocean floor sidescan, or photo and video system operated at 10 m above the ocean floor. The 1.14-inch diameter cable is also used to operate the RCV-150 garage/ROV system. The garage/ROV system has also been designed to act as a submersible rescue system with a submersible lift capability.

Jan 1, 1992

By Roger Amato

The 1982 United Nations Convention on the Low of the Sea includes provisions under Article 76 for extending a coastal State's jurisdiction beyond the 200-nautical-mile (nm) Exclusive Economic Zone (EEZ) and for establishing the seaward limits of sovereign rights over natural resources. Article 76 prescribes a set of methodologies for determining these outer limits based on physiography and sediment thickness. The methodologies were applied to each of the five continental* margin areas of the United States - Atlantic, Pacific, Gulf of Mexico, Alaska, and Pacific Islands-using existing digital hydrographic and geologic data. Figures 1 and 2 show the results of applying the methodologies to the Atlantic, Pacific, Alaskan, and Gulf of Mexico continental shelves. Figure 1 depicts the preliminary limits of each of the Article 76 determinations for the Atlantic and Gulf of Mexico continental shelves. The Atlantic limits were described by Carpenter, Thormahlen, and Amato (1995) at the 26th Underwater Mining Institute.1 The limits for the Alaskan continental shelves are shown in Figure 2. Additional areas beyond the 200 nm EEZ are highlighted. These include a small area north of the U.S. - Canada boundary, containing 7,000 km2, a large area north of Point barrow (395,000 km2), and a third area north of the Aleutian Islands (178,000 km2). The shelf between the first two areas appears to have sediments thick enough to qualify for the 1 percent method (Irish Formula); however, year-round ice cover has prevented acquisition of seismic or drill data. The entire northern Alaska shelf is prospective for petroleum The Gulf of Mexico (Figure 1) has two small areas beyond the EEZ known as "doughnut holes." One is south of Louisiana and includes part of the Sigsbee Escarpment, an area believed to have potential for oil and gas. Oil was found on Sigsbee Knoll in cores from Deep Sea Drilling Project's Leg 1 cruise in 1968. The Sigsbee areas contains about 6,000 km2. The second area is south of the Florida panhandle and contains about 12,000 km2.

Jan 1, 1996

By G. B. Carpenter

The United Nations Law of the Sea (LOS) Convention includes provisions (Article 76) for establishing the outer limits of a coastal State's continental shelf and for denoting the seaward extent of sovereign rights over natural resources. Determination of a coastal State's continental margin, according to Article 76, must consider eight factors: 1. The territorial sea baseline 2. The 2,500-meter isobath 3. The foot of the continental slope 4. A line 200 nautical miles seaward of the territorial sea baseline 5. A line seaward of the foot of the continental slope connecting the points where sediment thickness divided by distance to the foot of the slope equals .01 6. A line 60 nautical miles seaward of the foot of the continental slope 7. A line 100 nautical miles seaward of the 2,500-meter isobath 8. A line 350 nautical miles seaward of the territorial sea baseline Figure 1 shows the preliminary limits for each of the Article 76-based definitions for a portion of the U.S. Atlantic continental shelf. The additional areas gained beyond the 200- nautical mile Exclusive Economic Zone (EEZ) are highlighted. The first three factors are baselines from which the distance provisions of Article 76 are measured. Factors 4-8 are distance- from-baseline provisions for establishing the continental shelf limits. Factor 5, also known as the Depth of Sediment Limit or "Irish Formula", was calculated using sediment thickness data from seismic linesand isopach maps. All other factors were determined from digital hydrographic data. The Depth of Sediment Limit is the most advantageous method for the area shown in Figure 1. It is especially useful for introverted coastlines such as the Georgia Embayment and New York Bight areas. The 200-mile line is advantageous for protruding coasts such as those off major capes, e.g., Cape Hatteras. The 2,500-meter isobath plus 100-mile line gains

Jan 1, 1995

By H. I. Chesalova, M. Ye. Melnikov, A. M. Asavin

The discovery of iron-manganese ores on the surface of underwater mountains was made more than a half century ago. During this time the basic ideas about the thermodynamics of the processes of hydrochemical reactions in the sea water have been developed by scientists and are revealed in geochemical and mineralogical differences between the deposits from the seamounts and the nodules of the sea bottom. The distribution of the dissolved metals, oxygen, carbonic acid and organic matter in the overlying ocean waters of seamounts in the deep ocean to depths more than 5,000 m has been studied in some detail (e.g. J.R. Hein, P. Halbach. G.B. Baturin, Ye.M., S.I. Andreev, L.I. Anikeyeva, [1-6]). In recent years scientists from YUZMORGEOLOGY have completed detailed geological survey work on the Magellan Seamounts in the Pacific Ocean. The results of drilling the ore body and geophysical and photo surveys have also been described [4]. Previous ideas about the general covering of seamount surfaces with iron-manganese crusts have been changed based on ground-truth surveys. This study examines the complex concentric-zone or spotty arrangement of the most densely covered sections, the strong dependence of the thickness of crust on the geomorphologic features, and the potential influence of the underlying substratum. One established geochemical heterogeneity in the composition of ores, also frequently inversely proportional power dependence on directions was observed. The development of a numerical model of the formation of the ore crust on the seamounts is currently a high priority.

Sep 24, 2006

By Sven Petersen

The southern Mid-Atlantic Ridge (SMAR) is one of the least-explored spreading centers in the world with respect to hydrothermal activity. In the past 8 years research focused mainly on the ridge segments close to Ascension Island, discovering hydrothermal fields as far south as 14°20?S (Haase et al., 2007; German et al., 2008; Tao et al., 2011). However, the vast majority of the SMAR ridge axis has never been thoroughly investigated for hydrothermal activity. In the spring of 2013 we used segment-scale AUV deployments as well as conventional CTD surveys to identify areas of hydrothermal activity along 16 mid-ocean ridge segments between 13° and 33°S, thereby covering close to 5 % of the global ridge axis in a single cruise. During cruise MSM25 of the German research vessel Maria S. Merian, we tested longrange (>100 km lines per dive) AUV deployments of GEOMAR?s AUV ABYSS (a Remus 6000 vehicle) along the spreading axis for their capability to locate active venting in a fast and efficient way on regional surveys. Since the missions covered long distances,

Sep 14, 2011

By Raymond A. Binns

Drilling into an active hydrothermal system linked to convergent-margin felsic magmatism is a listed priority of the Ocean Drilling Program that addresses several fundamental geoscience issues. Solid and fluid products of felsic rock-water interaction, and the consequences for global chemical fluxes and for ore deposition, should differ from those in basaltic mid-ocean ridge environments already successfully tested by Legs 106, 139, 158 and 169. So, too, will fracturing controls on fluid pathways, and sources for metals and ligands. Researching the subsurface volcanic, structural/hydrologic, and mineralisation/alteration architecture of a drilled felsic-hosted system also has economic implications, especially for land¬based mineral exploration. A first-order hypothesis to be tested states that fluids derived from volatile-rich magmas are more important than recirculated seawater in convergent-margin hydrothermal systems - economic geologists increasingly appeal to this for creating "world-class" massive sulfide orebodies. Another hypothesis proposes "subhalative" massive sulfide deposition within hydraulically expanded volcanic products as a factor in generating large orebodies. Many second-order hypotheses such as leaching fractionated volcanics to cause gold enrichment in back¬arc systems also need testing. The thoroughly surveyed, active, PACMANUS hydrothermal field in the Eastern Manus back-arc basin of Papua New Guinea will be the site for ODP Leg 193 commencing in November 2000. It lies near the crest (1655-1750 m) of high-standing Pual Ridge, a 40 km-long edifice of dacite/rhyodacite with basal andesite all having geochemical and isotopic affinities with modern arc volcanoes of nearby New Britain. PACMANUS includes at least three focussed, high-temperature "smoker" sites with Cu+Au-rich massive sulfide deposits, and a field of diffuse, lower temperature venting through intensely altered dacite where modelling indicates significant subsurface mineralisation. Isotopic characteristics of deposits and vent fluids suggest magmatic contributions to the mineralising fluids.

Jan 1, 2000

By Peter A. Rona

The Mid-Atlantic Ridge in the central North Atlantic and the Gorda Ridge within the U.S. Exclusive Economic Zone off northern California and southern Oregon are yielding new discoveries of seafloor hydrothermal mineralization. The TAG hydrothermal field in the rift valley of the Mid-Atlantic Ridge near 26 degree N, 45 degree W has been a site of international collaborative research since the discovery there of extensive manganese deposits associated with low temperature hydrothermal activity in 1973 as part of the TAG (Trans-Atlantic Geotraverse Project). The first high-temperature hydrothermal activity, massive sulfide deposits and vent biota discovered in the Atlantic were found at the TAG hydrothermal field in 1985. Collaborative dive series with DSV ALVIN in 1990 and in 1991 with the two Russian MIR submersibles in the TAG field have found and sampled large inactive sulfide mounds in addition to the previously known active sulfide mound. The active sulfide mound on the floor of the rift valley is about 250 m in diameter and 40 m high with a concentric zonation of mineral types and flow regimes decreasing in temperature from 365 degree C black smokers at the center to white smokers and diffuse flow toward the margins. The recent dive series in coordination deep-towed instrument surveys have delineated a zone extending about 5 km along the lower east wall of the rift valley of inactive sulfide mounds up to a kilometer in diameter. MIR Mound in this zone consists of a central sulfide zone about 400 m in diameter and 50 m high surrounded by a halo of low-temperature deposits to 200 m wide. Inactive sulfide chimneys contain the first primary, free gold grains found at a hydrothermal site on a mid-ocean ridge (P.A. Rona, Y.A. Bogdanov, E.G. Gurvich, N.A. Rimski-Korsakov, A.M. Sagalevitch and M. D. Hannington, 199 1 EOS, Transactions, American Geophysical Union, 72:470-471 and Journal of Geophysical Research, submitted).

Jan 1, 1992

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By G. McMurray

The release by the U.S. Department of the Interior (DOI) of a Draft Environmental Impact Statement (DEIS) for the leasing of polymetallic sulfide minerals on the Gorda Ridge in December 1983 resulted in strong negative public reactions. The fundamental issues affecting federal-state relations included the amount of state involvement in the planning process and the continuing question of consistency (sensu Coastal Zone Management Act). The specific issues raised included the authority of DOI to lease nonenergy minerals offshore, the economic and strategic rationale for the proposed lease, and the adequacy of the DEIS. The questions of DEIS adequacy arose in three major areas: the lack of evidence for the existence of polymetallic sulfides on the Gorda Ridge, the lack of sufficient baseline data, and the lack of a mining scenario from which to assess potential impacts. The joint Federal-State Technical Task Force was formed in February, 1984 as part of an initial agreement between the State of Oregon and the Department of the Interior to work cooperatively. Other points in the agreement were (1) a reduction of any future proposed lease area from 40 million acres to no more than 4 million acres; (2) indefinite postponement of the lease sale; (3) deletion of the nearshore portion of the possible lease area covering the physical continental shelf and slope; (4) a commitment of a "tiered" EIS process; and (5) sharing of non-proprietary data with the public.

Jan 1, 1985

By S. Jeffress Williams

Continental shelf margins are dynamic sedimentary environments that contain important benthic habitats and support many functions such as navigation, national defense, cables, pipelines, trawling, and oil and gas and mineral extraction. Coastal margins also contain resources such as sand and gravel aggregates, which are becoming increasingly important for beach nourishment to mitigate coastal erosion and enhance recreation and to restore degraded coastal ecosystems. Existing geologic maps of the seafloor and sub-bottom sedimentary character, morphology, texture, composition, and other seafloor properties are not available for some regions, are out of date and not inclusive of the massive data collected during the past several decades, and are not in GIS-based digital formats. New geologic maps, based on unified and integrated national digital datasets, showing the sedimentary character of continental margins are critical tools for both research to better understanding the geologic history and processes of continental margins as well as the distribution of habitats and resources and for managing coastal-marine resources. The majority of existing seafloor maps are decades old and do not include recent data from mapping surveys, seabed sampling and observation carried out by federal agencies, universities and industry. Because continental margins are increasingly important, comprehensive and integrated databases are needed to produce GIS-based digital maps displaying information such as seafloor geology, sediment character, texture and distribution. To meet the need for a unified database of seafloor sedimentary character, the USGS is conducting the Marine Aggregate Resources and Processes project, a national assessment of marine sand and gravel with federal, state, and academic partners.

Jan 1, 2004

By Tetsuo Yamazaki

Seafloor massive sulfides (SMS) in the western Pacific have received much attention as resources for gold, silver, copper, zinc, and lead (Lenoble, 2000). Since the end of the 1980s, SMS have been found in the back-arc basin and on oceanic island-arc areas. The typical representatives found are in the Okinawa Trough and on the Izu-Ogasawara Arc near Japan (Halbach et al., 1989; Iizasa et al., 1999), in the Lau Basin and the North Fiji Basin near Fiji (Fouquet et al., 1991; Bendel et al., 1993), and in the East Manus Basin near Papua New Guinea (PNG) (Kia and Lasark, 1999). The higher gold, silver, and copper contents in one of the areas increased the chance for profitable mining operation, which was considered by a private company (Malnic, 2001). The company gathered investment money and announced to start the commercial mining from 2010 (www.nautilusminerals.com). On the basis of geological information of the Sunrise Deposit of the Myojin Knoll on the Izu-Ogasawara Arc (Iizasa et al., 1999) and geotechnical characteristics of SMS (Yamazaki and Park, 2003), some preliminary economic validation analyses of the SMS mining in small production scale were reported by one of the authors (Yamazaki et al., 2003; Yamazaki and Park, 2005; Yamazaki, 2007). The results showed high profitability of the SMS mining.

Jan 1, 2011

By Brian D. Bornhold

A comprehensive multi-disciplinary marine geological survey of northwestern Graham Island, Queen Charlotte Islands, British Columbia, Canada was conducted by Offshore Survey and Positioning Services Ltd. of Vancouver, B.C. on behalf of the Geological Survey of Canada; Energy, Mines & Resources Canada, Pacific Geoscience Centre, Sidney, B.C. Canada during October 1984 and July 1985. The aim of the survey was to map both the surficial geology and geomorphology in order to identify and evaluate the nature of the nearshore sedimentation and recent tectonics including stability (slumps and scarps) seafloor faults (frequency and displacements) and both the classification and consistency of soil type boundaries and properties. Data was acquired by utilizing conventional indirect applied marine geophysical techniques including side scan sonar, precision echo sounding and complimentary soil sampling. During October 1984 a total of 320 line kilometres of data including 180 soil samples were acquired. During July 1985 a total of 300 line kilometres of data were acquired including 150 soil samples.

Jan 1, 1985

By Gary J. Massoth

Are hydrothermal emissions from subduction-related volcanic arcs important to the total hydrothermal burden of the oceans? While historical observations of hydrothermal venting of fluids at mid-ocean ridgecrests, intra-plate hotspots, and backarc spreading centers are numerous, we remain poorly informed regarding the contributions from hydrothermal systems associated with oceanic submarine arcs. Here we report the chemical results from the first systematic assessment for hydrothermal activity at an intra-oceanic arc front. We discovered that 7 of the 13 submarine volcanoes that define a 260-km-long segment of the southern Kermadec arc north of New Zealand are hydrothermally active. Most significant here is that the chemical compositions of the various hydrothermal systems, inferred from back-extrapolation of observations of hydrothermal plumes, are diverse, and in many instances enriched in the concentrations of gases (e.g., CO2 and H2S) and metals (e.g., Fe and Mn) compared to effluents commonly discharged from mid-ocean ridges. If our results are generally representative of submarine arcs, whose global extent may equal one-third that of ridgecrests, the answer to our leading question could be a resounding yes in terms of both volume and chemical composition.

Jan 1, 2001

By Will Roberts, M. E. Williamson

After verification of methodology and testing of prototype systems during 2005/06, Nautilus Minerals expanded their Papua New Guinea (PNG) operations to a full commercial exploration program in 2007. Included was the deployment of sensors and survey systems to locate, characterize and verify massive sulfide deposits with potential as mine sites within the tenements held by Nautilus in PNG. This presentation discusses some of the gear developed and operated during the 2007 PNG investigation.

By Masaru Nakamizu, Tetsuya Fujii, Tatsuo Saeki, Ken-ichi Yokoi

Methane hydrate, a solid compound formed from methane and water, occurs naturally in permafrost regions on-land and in deep continental slopes offshore and has been examined as future energy resources. The existence of methane hydrate in the eastern Nankai Trough region, offshore Japan, was confirmed by drilling the MITI well “Nankai Trough” in 1999. Aiming commercialization of methane hydrate production, the Research Consortium for Methane Hydrate Resources in Japan (MH21, core associations: JOGMEC[*1], AIST[*2] and ENNA[*3]) under METI [*4] has been executing geological and geophysical surveys around the eastern Nankai Trough since 2001 as a nation project.

By Simon McDonald

The Neptune Group was established in 1999 to apply for exploration permits within New Zealand’s 200nm EEZ. These applications were to investigate and commercialise hydrothermal Seafloor Massive Sulphide (SMS) deposits identified by international researchers and to locate others. SMS are volcanically related seafloor accumulations of copper, lead and zinc with high levels of gold and silver. Neptune has three granted exploration licenses within the New Zealand EEZ and has application in other jurisdictions. Neptune undertook the world’s first commercial drilling exploration work of SMS in December of 2005.

Aug 24, 2006

By Alexander Malahoff

Six active Kermadec Arc submarine volcanoes located between 34°S and 36°30?S were mapped and sampled by an interdisciplinary inter-institutional research team between April and July 2005 using submersibles Pisces V and Pisces IV aboard the mother ship the RV Kai?mikai-O-Kanaloa. The purpose of the expedition was to study the relationship between hydrothermal activity, formation of hydrothermal mineral deposits and the biodiversity of life associated with the hydrothermal vents. Of the volcanoes examined, all showed evidence of hydrothermal activity, plume production and helium anomalies. Only two of the volcanoes, namely Brothers and Clark, showed chimneys and surficial poly-metallic sulphide deposition. Hydrothermal venting at a water depth of 1700 meters within the base of the northern wall of the summit caldera of Brothers Volcano has produced a field of chimneys, some of them 5 metres high with black smokers venting. Temperatures of 300°C were measured within the active vents. Clark Volcano has a double cone summit at a water depth of 875 metres. The shallowest cone has a near-summit hydrothermal vent field with 5-meter high venting chimneys and smaller structures around the periphery. Water temperatures of 200°C. Geochemical and petrological analysis of the massive poly-metallic sulphide samples taken from Brothers and Clark show a diversity of mineralogy. This diversity is clearly a function of hydrothermal water temperature. Chimneys sampled from Brothers are pyrite and sphalerite dominant with lesser chalcopyrite. Sulphides from Clark Volcano tend to be barite rich with lesser sphalerite and pyrite. Sulphides from Brothers Volcano have a range in gold composition of 4 to 58 ppb with silver composition of up to 38 ppb. A mineral formation model for the volcanoes suggests hydrothermal fluid boiling within the volcanic edifice for those volcanoes with shallow summits and massive sulphide deposition with the edifice as well. Surficial deposits include native sulphur and lower temperature oxides. Only the deeper water Brothers Volcano shows massive sulphide deposition along the marginal faults of the caldera floor.

Jan 1, 2005

By J. Bruce Gemmell

ODP Leg 158 drilled seventeen holes into the active TAG hydrothermal mound and underlying stockwork, 26°N, Mid-Atlantic Ridge. Drilling in five different areas, including a high-temperature black smoker complex and a lower-temperature white smoker vent field, revealed the multi-stage depositional history and character of sub-seafloor mineralization and alteration. The upper portion of the mound consist of massive pyrite and pyrite breccias which are underlain by pyrite-anhydrite breccias and then by quartz-pyrite breccias. Quartz-pyrite breccias grade down into silicified wallrock breccias. Chloritised basalt breccias occur at depths greater than 100 m. Several stages of quartz-pyrite±chalcopyrite veins occur in the stockwork zone and lower portions of the mound, whereas anhydrite±pyrite±chalcopyrite veins occur within the upper parts of the mound. Recovery of unaltered basalt near the edges of the mound has constrained the extent of the stockwork zone to a pipe-like feature 80 meters in diameter. A detailed sulfur isotope investigation of sulfides and sulfates within mound and the underlying stockwork zone has revealed the overall range of sulfide d34S analyses to be 0.35% to 10.27%. Anhydrite has a tight range of d34S values 20.55% to 21.56%. There are distinct differences in d34S values between the different textural types of pyrite (massive sulfide, breccia clasts, disseminations associated with alteration, and veins). The massive sulfide and breccia clasts have a similar distribution of d34S values (6%-8%), however the d34S values of the disseminated pyrite associated with the alteration are distinctly heavier (8%-10%). Vein sulfides have the lightest d34S values (5%-7%). Sulphur-isotope values at TAG are, in general, the heaviest reported for unsedimented mid-ocean ridge deposits.

Jan 1, 1998

By Takafumi Kasaya, Katz Suzuki, Yoshifumi Kawada

"INTRODUCTIONThe area beneath the seafloor preserves valuable resources that are inevitable to sustain our industrial society. Hydrocarbon resources such as petroleum and natural gases are one of the representative examples, which have been mined over a century (Brandt et al. 1998). In addition, submarine resources such as methane hydrates, ferromanganese crusts, and metal deposits of hydrothermal origin have long been known (Rona 2003; Kvenvolden and Rogers 2005), although methods of their mining have not yet been developed. All of these resources are distributed heterogeneously, and various exploration techniques have been developed and examined. The Japan Agency for Marine-Earth Science and Technology (JAMSTEC) is conducting a project on the development of exploration methods of these unexploited resources (Urabe et al. 2015; also see http://www.jamstec.go.jp/sip/images/pamphlet_e.pdf). The present study particularly focuses on our attempt on the developing an exploration method of hydrothermal ore deposits.Seafloor hydrothermal ore deposits are associated with submarine volcanoes of mid-ocean ridges, hot spots, and island arcs, and back arcs (Hannington et al. 2010). Active hydrothermal systems discharging high-temperature fluids can be detected above the seafloor as anomalies of temperature, turbidity, and acoustic impedance (e.g. Kasaya et al. 2015). However, because of the temperature limitation of mining (Boschen et al. 2013), the target of mining may be extinct and probably buried. To explore buried hydrothermal ore deposits from the vast seafloor area, geophysical surveys that can obtain information below the seafloor must be required. Several techniques including magnetic, electrical, and gravitational methods have been developed (e.g. Jones 1999; Kowalczyk 2008). Although physical properties taken by these methods are sensitive to the presence of hydrothermal deposits, difficulties are sometimes encountered. For example, anomalies of magnetic susceptibility and electrical conductivity, which characterize the presence of ore deposits, may be found above non-hydrothermal bodies such as volcanic bodies and reservoirs of hydrothermal fluids (e.g. Honsho et al. 2016). Thus, combinations of multiple methods must be used to specify the existence of buried hydrothermal ore deposits"

Jan 1, 2017