Search Documents

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By G. I. Voiloshnikov, V. E. Dementyev

"One of the most important advances in the world gold metallurgy is the introduction of adsorption technologies for processing of ores and concentrates. «Adsorbent-In-Pulp» process allows to eliminate pulp filtration that is especially important during processing of clay and slime bearing ores. “Adsorbent-In-Leach” process is one of the ways for processing of preg-robbing (carbonaceous) products. High efficiency, increased metals recovery, decrease in capital and operational costs, possibility of easy control and adjustment are the advantages of adsorption processes. Anion-exchange resins and activated carbons are used as adsorbents. This paper presents Irgiredmet experience on gold adsorption technology using both adsorbents (RIP, RIL, CIP, CIL processes). It includes results of long-term studies of different theoretical and practical issues of adsorption processes. Irgiredmet started development of ion exchange technology (RIP, RIL) in 1964. Laboratory and pilot plant tests were conducted to develop process design criteria for 15 RIP plants of the former USSR. During this test work a great number of newly synthesized resins including strong- and medium-base resins was studied, different types of adsorption feed (ores and concentrates) were tested; some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption for silver gold ore, improved flowsheet for gold elution and resin regeneration, designs of technological equipment for adsorption, elution, electrowinning processes including pulsation columns, electrowinning cells etc. were developed. Irgiredmet took part in commissioning of practically all RIP plants in the former USSR. Due to its efforts RIP process became to be the standard technology. Last Irgiredmet RIP projects include the development of adsorption technology using medium-base resin for the three mines owned by GC Petropavlovsk (Amur region, Russia). The complex of the testworks on activated carbon gold adsorption technology including the search of prospective activated carbons; study on gold adsorption mechanism; development, testing and introduction of process flowsheets and the equipment for their realization was conducted. The original gold elution process was developed. The developed CIP technology was firstly introduced at Lebedinsky gold plant (Yakutia). Now carbon adsorption technology is widely used at Russian gold mines as CIP, CIL, CIC processes. The most relevant example of CIP introduction is Svetlinsky gold plant (Ural, Russia) with capacity 8 Mt of ore/ year."

Jan 1, 2018

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By M. E. Taranenko, V. A. Krivonosov, S. A. Nemykin

"In concentrating production energy-consuming power installations are wide used, the most powerful of them are the wet autogenous grinding mill operating in closed circuit with a spiral classifier. The analysis of the current state of the automation of the grinding process shows that the reserves for maximizing productivity and minimizing electricity consumption have not yet been exhausted on the existing process equipment. Usage of the achievements of the modern management theory reveals an opportunity for further optimizing of the grinding process. The purpose of the research is to develop an automated control system of complex ""the mill-classifier"" to conduct the grinding process in the most operating efficiency, ensuring the maximization of productivity and minimization of specific electricity consumption. The main idea of this work is to study the specific features of the ore grinding process and creation on this basis of automated control system complex ""mill-classifier"" which allows to find and to maintain the optimal mode of grinding based on identification of the current object parameters, observance and regulating of the object state coordinates. Research methods. We used the methods of system analysis, mathematical statistics, modern automated control theory, theory of systems identification, optimal control, modelling of dynamic processes. Developed scientific provisions: - identification algorithm of the loading sub-system management object of complex ""mill - classifier"" allowing to obtain the unbiased estimators of its parameters according to the data of normal object exploitation; - observing device, which differs from the classic version of the observer Luenberger with possibility of estimating not only the state coordinates of the control object, but also the low-frequency perturbation component; - automated system stabilizing the active power of the grinding mode on the basis of a states controller with Luenberger observer; - structure of the software and hardware that implements the developed models, algorithms, methods of control, management and optimization in the framework of the automation of grinding."

Jan 1, 2018

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By A. Y. Senchenko, Y. V. Kulikov

"The most common technique for selection of grinding equipment is the Bond method implying determination of a ball mill work index (BWi). The method is perfect for greenfield projects where a ball mill must be sized to grind an ore to 80% passing 75-100 µm. Finer grinding will require application of specific correction factors to a standard equation since initially the method was not designated for sizing of fine (minus 75 µm) grinding mills. Significant issues are related to selection of grinding equipment for treatment of originally fine materials when the standard procedure is not applicable. In 1984, Levin published his special technique titled as “A proposed test for the determination of the grindability of fine materials”, where he offered to use the standard Bond ball mill for determination of a specific grinding energy. However, this method did not meet with wide recognition. In 2017, Institute TOMS under guidance of JKMRC’s specialists performed a testwork aimed at verification of a new universal technique for determination of grindability of initially fine materials. An object was to test three aged tailings samples for the subsequent modelling of comminution circuit and evaluation of potential throughput of the existing ball mills with final grind size of ?80 passing 53 µm. In parallel with development of the universal approach, TOMS’ specialists carried out tests according to the Levin method in order to compare the data resulted from two methods. The results from lab ball mill testing on three products following the alternative test methods are presented in this paper along with the testing methodology and results analysis. Specific energy was calculated for regrinding of the materials to the required size. Difference of the examined methods and assessment of their applicability for sizing of full-scale equipment are explored."

Jan 1, 2018

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018