Search Documents

By S. Mitra1

"This study aims to investigate coarse particle detachment mechanisms (particle diameter > 150 ?m) utilising both experimental and numerical technique. Two mechanisms were studied – (i) interactions of bubbleparticle (BP) aggregate with vortices and (ii) coalescence of bubble-particle aggregates. On the first mechanism, interaction behaviour of coherent vortex structures with a BP aggregate (bubble diameter db = 3 mm, particle diameter dp = 0.3 mm) was studied using a CFD model in the Reynolds number range of 100 to 1000. Effect of surface hydrophobicity on the BP stability was examined using a range of contact angle boundary conditions. To address the second mechanism, interactions of bubble-particle aggregate (db ~ 4 mm, dp ~ 0.4 mm) with both free gas-liquid interface and individual bubbles were investigated using high speed imaging. Both rebound and coalescence outcomes were observed to be responsible for BP instability leading to particle detachment.INTRODUCTIONIt is widely known that flotation process performs excellent mineral recovery for base metal ore particles that are typically in the range of ~ 20 to 150 µm in diameter (Jameson, 2010). More specifically, higher recoveries are usually reported for particles in the size range of ~20 to 70 µm while outside this spectrum, generally the recovery diminishes significantly. It would be highly desirable to improve the recovery of particles at the coarse end of the flotation size range spectrum which has significant economic benefit (Jameson, 2010). However, it is essential that insights to particle detachment phenomenon, the primary impediment in coarse particle flotation caused by the underlying hydrodynamic factors are first obtained at a greater depth.In an ideal quiescent liquid medium, due to inertia, coarse particles deviate substantially from the fluid streamlines and collision efficiency with bubbles decreases which can only be augmented by increasing turbulence level in the medium sufficiently to make random physical contacts with bubbles. Nonetheless, even if successful contacts are made, it is difficult for these large particles to remain attached to bubbles in a turbulent shear flow environment. There are two major mechanisms postulated for particle detachment – interaction of turbulent flow structures (eddies) with BP aggregate and coalescence among surrounding aggregates. Earlier work of Schulze (1982) theorised a vortex acceleration component to characterise turbulence effect on BP aggregate instability in flotation machines. Wang et al. (2015) investigated bubble detachment behaviour from a stationary particle in a nearly homogeneous and isotropic flow field. Using PIV (particle image velocimetry), it was shown that the local maximum energy dissipation rate for the case of bubble detachment was significantly higher than the no detachment case, and was also higher than the critical value for bubble detachment calculated using Schulze’ theory (Schulze, 1982). Later, Wang et al. (2017) also visualised the BP aggregate instability in a cavity flow leading to particle detachment which was attributed to bubble coalescence, bubble surface oscillation and particle deceleration phenomena."

Jan 1, 2018

By M. Ghiani, P. Massacci, A. Manni, R. Peretti, Center for Mining and Mineralurgical Studies, S. Serranti

"The research study has been devoted to point out the better way to process a colemanite concentrate characterised by a high content of two kind of As sulphides (realgar and orpiment) finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to determine all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.There is a not neglectable part of realgar highly disseminated into the colemanite crystals.The orpiment recurs in small acicular crystals of 20÷30 µm in length and 5 µm in width, very difficult to liberate from the colemanite mineral particles.The colemanite concentrate, in fact, has been addressed to a chemical plant which products were boric acid and gypsum, the contaminated by As. It was unacceptable for further applications and very dangerous if rejected in the environment.Grinding tests under dry and wet conditions have been carried out in order to evaluate the liberation modality of the As sulphide minerals from the colemanite.Some difficulties have been overtaken in order to obtain a selective liberation of the As sulphides from the colemanite even if a certain decreasing in As grade in the higher size classes has been registered.All the comminution products have been analysed by SEM monitoring the liberation degree of the mineralogical constituents.Flotation tests have been carried out after different comminution flow sheet adopting different modulating conditions in order to evaluate the influence of the following parameters:• collector concentration versus contaminants concentration (As minerals) in the froths;• kind and quantity of the frothing agent to maximise the mineral recovery in the froths;• kind and quantity of the modulating agents to maximise the selectivity of the process;• conditioning modalities in order to obtain a suitable dispersion of fines and to avoid segregation of Asbearingparticles together with colemanite ones;• solid/liquid ratio of the pulp to minimise the water flow into the plant."

Jan 1, 2003

By K. A. Natarajan

Involvement of various indigenous microorganisms in extracellular and intracellular iron oxide formation is a convincing index for iron ore biogenesis. Biomineralization of various iron oxides such as hematite, magnetite, goethite and limonite with the participation of aerobic and anaerobic microorganisms is well established. Various aerobic and anaerobic bacteria such as Gallionella, Leptothrix, Acidithiobacillus, Thermoplasmales, Pseudomonas, Bacillus spp and Shewanella putrefaciens, which are implicated in the formation of higher and lower oxides of iron have been isolated from different iron ore deposits. Diversity of microbial life in iron ore deposits can be put to beneficial use such as selective removal of undesirable constituents such as silica, alumina, clays, phosphorous and calcite and also to bring about environmental detoxification. Role of microorganisms such as Paenibacillus polymyxa, Bacillus subtilis, Yeasts and a sulfate reducing anaerobe in the biobeneficiation of hematite is illustrated. Surface chemical changes brought about by bacteria - iron ore mineral interactions are discussed with respect to hydrophobcity, adsorption isotherms, zeta potential data and bioreagents generation. Bacterial adaptation to minerals such as hematite, quartz, alumina, calcite, apatite and clays results in secretion of mineral ? specific biosurfactants such as proteins and polysaccharides. Such bioreagents can be used as selective collectors, dispersants and flocculants in iron ore beneficiation. Research results are highlighted to demonstrate silica, alumina, phosphate, calcite and clay removal from hematite. Environmental friendliness of such biobeneficiation processes is demonstrated with respect to biodegradation of toxic amine collectors, utility of ?in situ? organisms in enhancing settlement of fines in tailing dams and water harvesting. Keywords: bio-mineralization, bio-beneficiation, bio-remediation, Gallionella, Leptothrix

Sep 1, 2012

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Hoon Lee

Laboratory tests were conducted to evaluate the breakage characteristics of pyrophyllite in a laboratory ball mill. In grinding tests, the breakage characteristics were analyzed using the mathematical kinetic models based on the two breakage functions; the specific rate of breakage and the primary breakage distribution. Two samples having similar chemical composition show identical values in specific rate of breakage. In comparison, there are different values of primary breakage distribution for each sample. The size distributions of the product with various grinding time are well described by the parameters from non-linear searching.

Sep 1, 2012

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By Janusz S. Laskowski

It is customary to assume that wettability plays an important role in coal flotation, and it is well established that while hydrophobic metallurgical coals float easily, low-rank less hydrophobic coals are difficult to float. However, coal surface wettability plays a dominant role in many coal preparation unit operations. As it will be discussed in this paper, it affects coal-dewatering, selection of flocculants, fine coal pelletization and briquetting, and even coal handleability.

Sep 1, 2012

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By M. D. Vilarinho, W. Xuan, F. Vasconcelos Guimarães

"This article summarises the efforts to reduce the energy consumption in grinding in a magnetite ore beneficiation plant. ArcelorMittal Kryvyi Rih ore beneficiation plant produces magnetite concentrate at 65% Fe and 8% SiO2, of which the D80 is approximately 44µm after three stages of grinding with ball mills and magnetic separation. Characterisation and laboratory scale bench tests performed on samples from the beneficiation plant indicate that the industrial flowsheet could be simplified. After the first stage of grinding and magnetic separation, a significant size fraction of the intermediate concentrate is already well liberated. Therefore, it can be directly concentrated in a second stage magnetic separation without further grinding. If a screen of 150µm size can be implemented after the first stage of grinding-magnetic separation, only the oversize of screening, representing 35% of the material, requires secondary and tertiary grinding and magnetic separation. The combined concentrate from the two fractions already meets the industrial specifications. This new route can provide the same final product, with fewer mills; it saves around 30% in energy consumption only in the grinding step without changing the main structures of the processing plant.INTRODUCTION Comminution, including crushing and grinding, is responsible for at least 40% of total energy usage in mining and mineral processing. This paper shows an example to reduce grinding cost, by changing the flow sheet design strategy in ArcelorMittal Kryvyi Rih (AMKR).AMKR is one of the most important mining and steel complexes in Krivoy Rog basin in Ukraine, which has been studied over 100 years because of mining of iron ores. The iron ores are associated to Banded Iron Formation of the Saksagan suite, with an average iron grade of around 36 percent Fe. The total thickness of the Krivoy Rog Supergroup reaches 5-6 km, whereas that of the iron-ore Saksagan Group comprises up to 1400 m. High-grade iron ore extends to more than 2,000 m below present surface"

Jan 1, 2018

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003