Search Documents

Beneficiation and dephosphorization of refractory oolitic hematite ore are investigated in this paper. It is shown that single magnetic separation, gravity separation or flotation is unable to recover iron effectively from the ore due to the complex mineralogy. The joint separation by spiral chute-shaking table shows a prospect for the treatment of the ore. An iron concentrate with 58.67% iron grade and 51.93% recovery is obtained by the joint separation of spiral chute and shaking table under the fineness of ?0.074mm 90% and dispersant dosage of 2kg/t for a sample ore of 37.51% Fe and 0.88% P. However, P content in the concentrate is still up to 0.52%. Dephosphorization from the concentrate is hence carried out. The final iron concentrate assaying 59.26% Fe and 0.056% P is obtained when the concentrate obtained by joint separation is leached by sulfuric acid of 1% (mass fraction) with solid percentage 10% at room temperature for 10min.

Jan 1, 2014

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By A. V. Rasskazova

"The oxidized and mixed ores are processed by heap leaching. Primary ores with high gold content are floated. In recent years mining of primary ores with the low gold content (up to 4 ppm) has increased. Extraction of gold from these ores by floatation is technologically ineffective. Gravity concentration is ineffective for fine gold particles because of their floatability. The research objective was assessment of the viability of processing gold-bearing ore with combined gravitational and hydrometallurgical methods and testing of recovery of metals from a gold-copper oxidized ore chloride-hypochlorite leaching solution. The advantage of chloride-hypochlorite lixiviant is the low cost of reagents which is produced by the electrochemical synthesis of NaCl solution with the addition of HCl. The adsorption of chlorine compounds by a mineral matrix and its ability to oxidize the refractory ore components and allows for the application of chloride-hypochlorite systems for gold recovery for both oxidized and primary ores. The complexity and problem in using a gold–chloride system is the strong adsorption of gold–chloride complexes onto mineral surfaces, such as goethite, quartz, and alumina. In preliminary testing, gold recovery from gravity circuit gold bearing concentrates processed by agitation leaching in chloride-hypochlorite solution, gold recovery has reached up 82% after 4 hours of leaching. Chloride-hypochlorite leaching of copper-gold oxidized ore with preliminary processing by sulfuric acid provided for 94 % gold recovery to solution. Understanding of ecological hazard of cyanides is the motive power of researches in the field of search non-cyanic chemistries to provide for technologically and economically effective solvents of gold. Soluble compounds of chlorine with a suitable oxidizer are one of the alternatives to cyanides. Basic researches of gold extraction by chloride-hypochlorite solution have shown high rates of gold recovery.INTRODUCTION Because of the continued and growing environmental concern for the use of cyanide for gold processing, interest for the use of non-cyanide lixiviants, especially with halides has renewed recently (Tran et al., 2001; Ferron et al., 2003; Bhaghalha, 2007). Leaching solutions based on halides (chloride, bromide and iodide) are viable alternative to cyanide (Kwang et al., 2008). The major disadvantage of the chlorine–chloride system is the high reactivity of chlorine in reaction with sulfide and gangue carbonate minerals. It is believed that only high grade materials may be treated by chlorine–chloride systems economically (Baghalha, 2007). Another important problem of the application of gold–chloride complex is that it tends to be rather unstable and may re-precipitate upon contact with a reductant, such as sulfidic minerals of ore. It is well known that Au(III)–chloride hydrolysis species are strongly adsorbed by goethite, quartz, and alumina (Machfsky et al., 1991). To minimize adsorption of gold–chloro complexes, it works best to minimize the adsorption time."

Jan 1, 2018

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy. These micro-organisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation (Duarte et al., 1993; Norris and Barr, 1988; Konishi et al., 1995). These extreme thermophilic Archae, characterised by a different cell envelope structure (König and Stetter 1986, König 1988, Michel et al. 1980) perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathwaysThe active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity. While limited study on the influence of the solids phase on thermophilic leaching performance is reported, initial reports suggest that the thermophiles used for bio-oxidation appear to be sensitive to hydrodynamic conditions (Jordan et al 1993, Clark and Norris, 1996) and the presence of solids (Norris and Bar 1988, Le Roux and Wakerley, 1988, Escobar et al. 1993, Torres et al. 1995, Nemati and Harrison, 2000)."

Jan 1, 2003

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003

By Güven Önal, Zeki Dogan, Neset Acarkan

"In general, the processing of glass sand may involve comminution, washing, wet classification and attrition scrubbing. Additional processes may include magnetic separation, flotation and leaching in various combinations.Yaliköy sand dune deposit is located near to Istanbul on the European side by the Black Sea coast. The reserve of deposit is around 70 million tons. Iron content of Yaliköy sand dunes is 0.48 % Fe2O3 and not suitable for glass manufacture. The iron content of glass sand should be less than 0.15 % Fe2O3 for window glass manufacture and 0.05 % Fe2O3 for glassware. In this study, it was aimed to produce glass sand with less than 0.15 % Fe2O3 for window glass and with less than 0.05% Fe2O3 for glassware manufacture from Yaliköy sand dunes. A representative sample with a weight of 200 kg was taken from Yaliköy sand dunes deposit through opening small pits.• Mineralogical studies have shown that iron is present in three forms:• Hematite, limonite, clay and iron silicate minerals such as epidote and garnet occur in free form.• Quartz grains are coated by hematite and limonite.• Iron is also present in the cracks of quartz grains.Free iron minerals such as hematite and limonite and silicate minerals were subjected to magnetic separation and flotation for removal. Iron coatings were tried to be removed by scrubbing and leaching. Iron removal in the cracks of quartz grains was attempted by grinding and leaching.Under optimal conditions, sand concentrate with 0.38 % Fe2O3 was obtained by means of high intensity disc type magnetic separation. Grinding and scrubbing were applied to see the effect of size reduction and attrition at room temperature and 90 ºC, by using non-magnetic fraction. Sand concentrate with 0.13% Fe2O3 was obtained at 90 ºC in this test.Sand sample which was previously ground to minus 0.5 mm and scrubbed, was floated by using sulphonates as collector. After flotation tests, sand Concentrate was obtained with 0.11 % Fe2O3.The optimum iron removal was achieved by H2SO4 leaching at 90 ºC depending on acid concentration and leach duration in static, percolation and agitation leaching. Agitation leaching was done by the use of mixer at 600 rpm, 50% solids and leach duration was 15 minutes."

Jan 1, 2003

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By R. Mukherjee

Consistency of Run-Off-Mine (ROM) quality plays an important role in mineral processing which is not very often talked about. The major impediment is limitation of sampling ROM ore, which makes processing plants to run without any realtime feedback on ore quality that comes in. The process of direct determination of Run-Off-Mine (ROM) ore quality is expensive and time consuming as drawing and preparing representative samples from blasted muckpiles are constrained by large sample size and inherent heterogeneity in terms of size and chemistry. In absence of techniques for direct measurement of quality, monitoring and control of ROM, feed to the processing plant at Joda East Mine, like all other iron ore beneficiation plants worldwide, is largely based on blasthole sampling and subsequent chemical analyses of blastcone chips. While such indirect methods proves to be more accurate for representing whole of a mining block or blasted muckpile (~30-50KT/blast), it is indeed a challenge to ascertain and predict day to day input quality for a part there off. This eventually leads to a gap between predicted and actual ROM quality, resulting in difficulties in process control, in turn, and leading to wide swings in product quality. Hence, it is imperative to bridge the gap between predicted and actual ROM quality by arriving at means, which ensure consistent plant feed grade to deliver consistent output. The paper discusses an efficient and affordable alternative for effective prediction of ROM alumina which has been developed by integrating blasthole quality database in GPS based Truck Dispatch System (GPS-TDS) at Joda East Mine. Initially, GPS-TDS has been installed for optimizing production parameters only, but this development has helped in further utilization of GPS-TDS for real time quality monitoring by improving ROM grade prediction and scheduling from several ore blocks in active mining areas. Keywords:run-off-mine (ROM), blast hole, feed grade, GPS-TDS

Sep 1, 2012

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By M. Rudolph, E. Schach, M. Buchmann, T. Leißner, N. Krupko, U. Peuker, M. Kern

"In mineral processing, density and magnetic susceptibility are two very fundamental properties. For the beneficiation of valuables to produce a saleable concentrate a detailed understanding of these properties is essential. Especially when it comes to the processing of cassiterite, which is the main mineral for tin production, they become highly prominent. Due to the chemically inert character of cassiterite towards most industrial applied leaching agents, density and magnetic separation processes are mainly applied for its beneficiation. To guarantee an optimized utilization of the different operations not only cassiterite but also the different gangue minerals have to be considered. In this study, a skarn ore is characterized by density and magnetic susceptibility. Therefore, the material was first split into different density classes by heavy liquid separation. The obtained classes were further separated by their susceptibility to finally obtain a density-susceptibility matrix. For this purpose, an isodynamic separator was used. A more detailed characterization of the materials is done via gas pycnometer, magnetic susceptibility balance and vibrating sample magnetometer to estimate the characteristics of density and susceptibility for the various classes. Further, the determination of the chemical assay and the mineral intergrowth by mineral liberation analysis is used to generate a three dimensional database for detailed characterization of the present ore. The objective of this study is to estimate potential material streams for a modular processing plant via characterization of the material for the entire deposit by the two afore mentioned characteristic properties. The established multidimensional data matrix, enables predictions for the separation properties of the material and contributes to the characterization of the deposit within the context of geometallurgy."

Jan 1, 2018

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By Fu Ping-Hao, J-P Franzidis, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton's Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003