Search Documents

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

By S. Nitta

The present study deals with a new approach in calculating the size of Tower Mills. The method is derived from the application of grinding kinetics theory on the analysis of by-gone operational data. It requires only information on the capacity of the mill to be designed, the product fineness and the Bond?s work index to give an accurate and simple prediction of Tower Mill characteristics. An example illustrates the different steps of calculation.

Jan 1, 2014

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By J. Bhattacharya

In many different ways industrial raw materials resources industry as a whole has accepted the principles of sustainable development and has made a commitment to move toward this goal. The critical question now is ?how?? While many companies have adopted policies and are implementing community relations programs, sustainability is not always ?lived? throughout the organization. While traditional programs and commitment from the top are critical, employees within all functional areas can advance sustainability. Individuals can make difference at all organizational levels, and it is this collective action that is so critical for enhanced financial performance as well as the preservation of the industry. Keywords: value chains, sustainability, legislation, auditing process

Sep 1, 2012

By R. C. Miranda

Flotation is an operation widely used in mineral processing because of its aptitude to recover minerals of interest very efficiently. Flotation is often responsible for making possible the exploitation of mineral deposits of low concentration. In flotation various processes phenomena occur, some of which have still not been explained scientifically. Due to this fact, there are no models that can be widely applied in flotation control. Thus, in most cases, the control is done by experienced operators who are able to visually classify the types of foam into different categories and each one of them is associated with an operating actuation. In this situation, image analysis is configured as a solution that has already been employed in several ways. In this paper, a control strategy based on the colour of froth on a direct flotation of a nonferrous metal is presented. Moreover, the paper reveals the theoretical basis of the method, the critical points, difficulties and improvements that can be implemented. Data of grade were collected from the mineral of interest and RGB (red, green and blue) data of final concentrate of the froth. The mineral grade was collected and analysed during one month of operation and RGB was obtained using a camera. It was verified that the red colour showed the same trend of the grade curve in the concentrate. Thus, the use of this online data in optimising control was introduced. The laboratory grade is used to calibrate the colour set point. Therefore, it was possible to monitor in real time the trend of enrichment and depletion of a non-ferrous mineral in a flotation. It was possible to establish an online control strategy based on simple data acquisition. The result was an increase of 10% on production.

Sep 1, 2012

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By A. Üçyildiz

Magnesium borates of varying compositions and properties are synthesized using different reagents and methods for the possible potential uses as termoluminescent material, anti-wear and anti-friction additive, fire retardant, catalyst for the conversion of hydrocarbons, whisker material and ferroelastic material. In the current work, the conditions for synthesizing MgB4O7 compound by high-temperature solid-state reactions were investigated using boric acid and magnesium oxide as the starting materials. The MgO:B2O3 mole ratios applied in the experiments were 1:1, 1:2, 1:3 and the thermal behaviours of each mixture were studied between 25~1200°C by TG/DTA analyses under static air atmosphere to find out the probable formation temperature of MgB4O7 phase. Considering TG/DTA results, freshly prepared boric acid and magnesium oxide solid mixtures were heated at predeter-mined temperatures and the phases were identified by XRD analyses. Accordingly, MgO:B2O3 mole ratio of 1:2, heating temperature of 950°C and a reaction time of 2 hours were selected as the optimum conditions for the formation of maximum amounts of MgB4O7. After obtaining solids prepared at the pre-determined optimum conditions, their chemical composition, IR spectrum, TG/DTA pattern, B.E.T. surface area value, particle size distribution and SEM images were deter-mined to point out the possible use areas. Experimental results showed that it was not possible to obtain pure product at the optimum conditions due to formation of minor amounts of t-Mg2B2O5 and the presence of some unreacted B2O3. The product synthesized has the potential for use as a corrosion inhibitor on some metal surfaces.

Jan 1, 2014

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

There is a strong demand for nickel metal due to quick development of stainless steel and new electrical materials, most of which is extracted from sulfide resources, resulting in a serious depletion of sulfide resources. Therefore, more attentions have been paying to extracting nickel from nickel laterite, which accounts for some 50% of total nickel metal production. In this paper prereducing?magnetic separation?reduction smelting process is developed to manufacture ferronickel rom two types of nickel laterite DN and GN, assaying 1.42% 1.83% Ni and 49.09% 26.08%Fetotal, respectively. Mineralogy of two types of nickel laterite was determined and optimization of process parameters was conducted to manufacture ferronickel. Prereduction?magnetic concentration process is used to upgrade low grade nickel laterite firstly, two kinds of Ni-Fe concentrates being prepared of DN assaying 2.26% Ni and 69.45% Fetotal and GN containing 2.76% Ni and 38.00% Fetotal. Finally, two types of ferronickel were produced by reduction smelting of prereduced concentrates DN and GN, DN and GN ferronickel contains 2.97% Ni and 6.58%Ni, 89.25%Fetotal and 89.95%Fetotal, respectively. The total recoveries of Ni and Fe of the two ferronickel are beyond 90% and 80%, respectively. There is significant difference in grade of magnetic concentrates and ferronickel between DN and GN laterite due to their different mineralogy, the former belongs to limonitic laterite and the latter saponite one. There are some advantages for this process to manufacture ferronickel from nickel laterite, including effectively upgrading low grade nickel laterite by prereducing?magnetic separation technique, higher throughput and lower energy available for reduction smelting section due to some 40% gangue being rejected in pre-upgrading section, and much less metallurgical coke consumption by using non-coking coal as reductant for prereducing?magnetic separation?smelting process.

Jan 1, 2014

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates."

Jan 1, 2003

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By R. C. Dunne

As ore grades of existing and new ore deposits continue to decrease there is ever increasing pressure to decrease operating costs to maintain profitabitabitiy at existing mine sites and for new projects. The accepted solution to this dilemma in most cases is to increase treatment rate, leading to a coarser grind, at the expense of marginal decreases in recovery. The recovery loss is usually associated with losses of liberated and composite coarse material. This paper will review the practice of coarse particle flotation, including the reagent chemistry, cell hydrodynamics, froth stability, entrainment and flotation cell design, all parameters important to the recovery of coarse liberated and composite particles. This will provide a better understanding of opportunities to improve the recovery of coarse particles. Some examples will be provided.

Sep 1, 2012

By de Vaux. Deryck, Natalie J. Shackleton, Vratislav Malysiak Cyril T. O. Connor

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. This investigation aimed at reducing surface passivation of pentlandite and inadvertent activation of pyroxene, thereby improving ultimate valuable mineral recovery and selectivity. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion.The addition of diethylenetriamine (DETA) reduces the copper concentration on both minerals, predominantly on the pyroxene surfaces and polyphosphate further enhances the selectivity at pH 6.The microflotation and batch flotation data obtained has shown a significant improvement in the ultimate flotation response of valuable mineral recovery and concentrate grade compared to the standard reagent regime, while the continuous flotation results significantly improved the selectivity, however, at a similar ultimate recovery."

Jan 1, 2003

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012