Search Documents

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

Electrochemical behaviors of synthetic and natural enargite in buffer solutions have been investigated using open circuit potential, stationary polarization and cyclic voltammetry as functions of solution pH, scan direction, scan range, scan rate and dissolved O2. The results indicate that the electrochemical behaviors of synthetic and natural enargite are very similar; solution pH, scan direction, scan range and scan rate have remarkable effects on the electrochemical behavior of enargite while dissolved O2 has little effect on the electrochemical behavior of enargite. The potential range in which enargite possesses the ability of passivation is from ?0.9 V to + 0.83 V vs. SCE. Enargite is most stable in neutral and alkaline solution around potential ?0.2 V vs. SCE. The main oxidation products on enargite surface in alkaline solution are Cu(OH)2 while the potential imposed on it is within the range of ?0.2 V to 0.33 V vs. SCE and Cu(OH)2 + S0while the potential applied is higher than 0.52 V vs. SCE.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By K. D. Mehta

Copper concentrate containing complex sulphides of Cu-Ni with 14.13% Cu and 10.04% Ni besides impurities such as 0.33% Co and 0.71% Mo, is not acceptable to the copper smelters due to the smelting problems. Selective bioleaching of nickel from the concentrate can be considered an an option to make it suitable for copper smelter. Effect of elemental sulphur and pyrite on the bioleaching of Ni and Co has been investigated using a mixed culture of Acidithiobacillus ferrooxidans (A.f.) and Acidithiobacillus thiooxidans (A.t.). Parameters such as pH, temperature, particles, size etc. were optimised to understand the role of additives in the bioleaching. With 2% S at 308K, 2.0 pH, 5% pulp density and 200µm size particles while shaking at 100 rpm, 79% Ni, 41% Co and 5% Cu were bioleached as compared to the leaching of 81% Ni and 45% Co in presence of 10 wt% pyrite in 60 days; 27% Ni, 24% Co and 4% Cu were recovered in sterile experiment. The selective dissolution of nickel and cobalt as compared to copper may be explained by galvanic interaction between chalcopyrite: pentlandite / pyrrhotite. Bioleaching was facilitated by strong oxidizing conditions due to higher Fe3+/Fe2+ ratio/redox potential (ESCE) as a result of improved interaction of minerals through biooxidation of sulphur and accelerated galvanic interaction by pyrite. The mechanism of selective leaching of Ni and Co was established by XRD phase identification.

Sep 1, 2012

By Bent Babel, Martin Rudolph

"The characterization of reagent-mineral interactions in flotation systems of finely intergrown ores holds difficult challenges for the applicability of standard techniques like Hallimond tube tests and contact angle experiments or renders them impossible due to a lack of sufficient samples in terms of quality and quantity. This disadvantage may not apply to more sophisticated techniques, but these often do not work in an aqueous environment. We present the utilization of an atomic force microscope with a hydrophobic colloidal probe to characterize the wettabilities of individual mineral domains of an ore sample, while additional spectral information is gathered by Raman spectroscopy. The exemplary ore sample investigated is mainly containing cassiterite and quartz, therefore the reference measurements like Hallimond tube tests and contact angle experiments were carried out with this binary system as a comparison. The focus of the study lies in the correlation of data gathered by the atomic force microscope and the Raman spectrometer with data from standard techniques. Finally, the applicability of the colloidal probe atomic force microcopy technique for reagent-mineral investigations is critically evaluated.INTRODUCTIONThe focus of this paper is the application of colloidal probe atomic force microscopy (CP-AFM) for theinvestigation of reagent-mineral interactions on a binary system of cassiterite and quartz. This and similar concepts using hydrophobic AFM probes have been applied by multiple authors (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b; Wada et al., 2017; Xie et al., 2017). The hydrophobic interaction is the main interacting mechanism for the hydrophobic colloidal probe with hydrophobic sample surfaces and the long range attractive component has been accounted to nanobubbles on the interacting surfaces (Yakubov et al., 2000). More detailed information on nanobubbles are available in two reviews compiled by Attard and Hampton (Attard, 2003; Hampton and Nguyen, 2010). This paper is based on the work by Rudolph and Peuker comparing different AFM based measuring concepts, additionally gathering data with Raman spectroscopy and correlating results of microflotation and CPAFM measurements (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b)."

Jan 1, 2018

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By H. Tiefel, M. Schneider, T. Neesse, J. Regler, J. Dueck, F. Donhauser

In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Control systems of large hydrocyclones are usually fitted with controllable underflow nozzles, which is not practical for small hydrocyclone batteries. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was invented at the LUR in cooperation with AKW Apparate und Verfahren GmbH & Co. KG. This process was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.

Jan 1, 2003

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014