Search Documents

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By P. T. Nguyen

The analysis of particle capture by an air bubble by two separate phenomena of collision and attachment has been difficult due to the uncertainty in determining when and where the two phenomena begin and terminate at the bubble surface, respectively. Therefore, a unified analysis was developed by solving the motion equation for the particle capture as one process. No distinction be-tween collision and attachment was made. Both the liquid film described by the micro-hydrodynamic resistance functions and the surface forces were included in the new model. The model predictions with the DLVO (Derjaguin-Landau-Verwey-Overbeek) surface forces did not agree with the experimental trajectories of latex and silica spheres. The model predictions with the inclusion of the non-DLVO attractive surface force agreed with the experimental data. The non-DLVO force reduced the repulsion between the non-attaching particle and the bubble, and significantly increased the attraction between the attaching particle and the bubble. The unified analysis is capable of predicting particle capture without the use of the induction time. The unified analysis also shows significant influence of the short-range hydrodynamic interactions on the collision which has been previously ignored.

Jan 1, 2014

By Frank Cappuccitti, Stephen Chryssoulis, Stamen Dimov

Surface organic microanalysis of platinum (Pt) and palladium (Pd) minerals by TOF MS1 is an attractive complement and potential alternative to conventional collector screening methods. Its attractiveness lies on its ability to focus on individual Pt and Pd mineral particulates, therefore providing a more targeted approach. The only requirement is knowledge of the occurrence (mineral composition, grain size and association) of Pt/Pd in the feed sample. This newly developed technique can detect, and identify collectors and quantitate loadings on individual Pt/Pd mineral particulates at plant concentration levels. Using this technology, collector loadings were measured on Pt and Pd metal plates and on PtS2 and PdS particulates which had been exposed together to aqueous solutions of different collectors. Thus, data were obtained on collector selectivity, the effect of sulphur; and of depressants, the latter in combination with TOF-LIMS2 results. Staged rougher tests on North American and UG-2 ores linked Pt/Pd flotation kinetics with collector loadings and ultimately grade/recovery.

Jan 1, 2003

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Thomas Mütze, Petya Atanasova, Kai Bachmann, Urs A. Peuker, Thomas Leißner

"A method is presented for the evaluation of mineral processing by liberation and upgrading. The method bases on the plot of recovery of valuables versus the recovery of gangue (Fuerstenau upgrading curve). The locking curve of a feed material was plotted together with the upgrading curve in a Fuerstenau diagram. The assessment of liberation and upgrading is done by a comparison of surfaces formed by the curves and some characteristic lines of the diagram. This plot allows the calculation of two new quantitative measures for liberation and upgrading. Both parameters can be combined to a third parameter describing the quality of the whole technical setup for mineral processing by subtracting the upgrading parameter from the liberation parameter. The third parameter shows a positive value in cases of upgrading determined processes, a negative value in cases of liberation affected processes and about zero for processes affected equally by liberation and upgrading. Thus it is easily possible to distinguish between poor results in the mineral processing caused by insufficient liberation or poor results caused by insufficient upgrading. Preliminary results from two case studies, performed on two different ore types, are very promising illustrating the practical use of such an approach."

Jan 1, 2014

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By P. Fecko

The objective of the paper was application of bacterial leaching on two brown coal samples from locality Mine Druzba, seams Antonin and Josef (Sokolov brown coal basin, Czech republic). Based on the results of bacterial leaching and petrologic analyses of the given samples, it is possible to say that application of bacterial leaching gived good results. Applying bacterial leaching it is possible to remove from 34% to 47% of total sulphur and from 45% to 64% of pyritic sulphur from the coal.

Jan 1, 2014

By Zhang Zhonghan

A domestic tungsten-tin ore presents very complex property. How to effectively recover the scheelite, wolframite and cassiterite in the ore has long been a difficult problem to be solved urgently. On the basis of process mineralogy study, a main flow-sheet for effective recovery of tungsten-tin minerals has been developed, which including ?fine grinding of feed?bulk flotation of all sulfides followed by their selective separation?iron recovery by LIMS?tungsten-tin minerals bulk flotation using new technique developed by our institute?tungsten-tin recovery by gravity from above tungsten-tin bulk flotation tailings?. As for the treatment of tungsten-tin bulk rougher concentrate, several flow-sheets of tungsten-tin separation by direct hydrometallurgy or a flow-sheet consisting of scheelite cleaning at elevated temperature followed by the gravity separation of scheelite cleaner tailing?separation of wolframite from cassiterite by dry HIMS or by direct hydrometallurgy are developed. For a low grade head ore, all valuable sulfide, magnetite, scheelite, wolframite and cassiterite are recovered with satisfactory in lab scale test. Keywords: micro-fine cassiterite, tungsten-tin bulk flotation, gravity separation-flotation-dry HIMS combined flow-sheet, hydrometallurgy

Sep 1, 2012

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By M. Niinae

Electrokinetic soil remediation by electroosmosis and ionic migration is restricted to soluble sub-stances. At a higher pH, the soil particles sorb more heavy metals, such as cadmium, than at a lower pH and the precipitation reactions of heavy metals are promoted. Both mechanisms make heavy metals immobile, rendering clean up more difficult and electrokinetic extraction inefficient. There-fore, the acidification of soils is very important to increase the clean up efficiencies of heavy metals, such as cadmium by electrokinetic method from contaminated soils. In the present study, acidification of soils and cadmium transport are predicted with a numerical method in which electrical flow is coupled with hydraulic flow, and the sorption process in the soils is induced in the model. The effects of some factors such as electrode configuration, electric field strength and electrode spacing for saturated soils are investigated using this numerical model. The results obtained this study are summarized as follows: The two-dimensional electrode configurations containing cathode surrounded by three or more anodes rapidly acidify the soils and remove cadmium from soils compared with one-dimensional electrode configuration. However, two-dimensional electrode configurations develop spots of inactive electric field between cathodes. A larger electrode spacing increases the processing time required, and it was also found that a larger electric field strength reduced the processing time required.

Jan 1, 2014

By A. Muhammad, A. Abdelaal, M. EL Salmawy

"Energy is vital for economic growth and sustainable development. Greater efforts are being devoted to developing unconventional energy resources such as oil shale as an alternative promising source of oil or solid fuel supplement. The main object of this contribution is to determine the upgrade potential of El-Nakheil oil shale using froth flotation. Samples were prepared by comminution followed by sieving into different size fractions. The flotation behavior of the material and extent of cleaning was studied with respect to nonionic and ionic collectors of anionic and cationic types. It was found that the organic rich portions could not be rendered sufficiently hydrophobic by the used collectors and selectivity towards surfactant was very low."

Jan 1, 2014

By Masanori Mori, Hajime Miki, Osamu Ichikawa, Tsuyoshi Hirajima, Mitsuru Sawada, Keiko Sasaki

For pretreatment of selective flotation, surface oxidation of chalcopyrite and molybdenite was applied by oxygen plasma then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Jan 1, 2014

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By Wantae Kim, Hoon Lee, Kwanho Kim, Sangbae Kim

Mechanochemical activation of starting minerals and their effect on the solid-phase synthesis and properties of ceramics with lower thermal expansion coefficient was examined. The mineral mixture, pyrophyllite-gibbsite-lithium carbonate, was prepared for the synthesis of ?-eucryptite (Li2O•Al2O3•2SiO2). Dry grinding using a planetary ball mill promoted the amorphization of the starting mixtures. XRD and FT-IR results showed that the crystallization of the target materials occurred from the ground mixtures by calcination. The crystallization of them increased with increment of grinding time and calcination temperature. In the synthesis, the trace of undesired phases such as quartz and cristobalite once formed during calcination at the temperature range from 750 to 850 °C almost disappeared and monophase ?-eucryptite was formed in the ground mixture at 950 °C. The lowest liner thermal expansion coefficient (TEC) of ?-eucryptite prepared was -2.5x10-6•°C-1. The thermal expansion behavior characteristics of the calcined

Jan 1, 2014