Search Documents

By P. Prusti

An air dense medium fluidised bed separator (ADMFBS) is the efficient process for dry beneficiation of coal. Magnetite powder is used as medium to make required pseudo-fluid density in the fluidised bed. The dynamics behavior of coal particle with reference to its position changes from ideal solution to pseudo-fluid condition in different bed densities depending on its shape, size and density. In this study, three set of projected areas of coal particles were taken. Each set contains four different shapes i.e., cubical, rectangular prism, spherical and triangular prism with different density starting from 1.3 to 1.8 gm/cc. It is observed that coal particles having density less than the bed density, floats in different positions in the dense medium fluidised bed. Higher projected area particles float in deeper height in comparison with smaller projected area. The difference in position of coal particles in the bed increases (nearly 1 to 4 cm) as the coal density approaches towards bed density irrespective of the different shapes. Different shapes of coal particles behave in different ways based on the operating parameters like bed density, coal density and projected area of coal particle. Empirical model equations are proposed to predict the position of coal particle of each shape in the air dense medium fluidised bed system. Keywords: ADMFBS, particle dynamics, projected area, shape

Sep 1, 2012

By Wantae Kim, Hoon Lee, Kwanho Kim, Sangbae Kim

Mechanochemical activation of starting minerals and their effect on the solid-phase synthesis and properties of ceramics with lower thermal expansion coefficient was examined. The mineral mixture, pyrophyllite-gibbsite-lithium carbonate, was prepared for the synthesis of ?-eucryptite (Li2O•Al2O3•2SiO2). Dry grinding using a planetary ball mill promoted the amorphization of the starting mixtures. XRD and FT-IR results showed that the crystallization of the target materials occurred from the ground mixtures by calcination. The crystallization of them increased with increment of grinding time and calcination temperature. In the synthesis, the trace of undesired phases such as quartz and cristobalite once formed during calcination at the temperature range from 750 to 850 °C almost disappeared and monophase ?-eucryptite was formed in the ground mixture at 950 °C. The lowest liner thermal expansion coefficient (TEC) of ?-eucryptite prepared was -2.5x10-6•°C-1. The thermal expansion behavior characteristics of the calcined

Jan 1, 2014

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By M. Pischtschan, S. Belz, M. Perrucci

In High Pressure Grinding Rolls (HPGR), the material grinding takes place between the fixed and floating rollers. In this regard, the rollers start to wear over a period of time, which is impacted by for e.g.: ore characteristics, operating pressure, feed material size and non-uniform feed presentation across the roller width. HPGR operational experiences have shown that the rollers do not wear at the same rate. This differential wear rate over time leads to differences in the tangential speeds of the rollers, causing an uneven gap between the fixed and floating rollers in relation to the material. This unwanted but extremely common situation results in a less effective grinding process due to the fact that the slip between rollers is not optimal. As the rollers wear profile increases, the roller with smaller diameter starts to wear further, deteriorating the comminution efficiency up to a point where operators have to stop the HPGR to replace the rollers. Since the wear rate of the rollers is not equal, the replacement of the same cannot be properly planned so that their life-time are fully utilized. In this paper, a dynamic load share control with the use of ABB’s variable speed drive system is proposed, which provides the possibility to the HPGR operator to impact the roller wear in such a way that it equalizes the wear rate to a certain extent and extends the roller life time. Called RollXtend™, this solution includes a load share factor which can be parameterized based on the wear measurement performed manually during maintenance procedure. Additionally, this paper describes an automated load sharing concept based on a non-invasive wear measurement method. The partial results of the technology trial in a copper/gold mine are presented, which aimed at detecting stud damage and estimating the real rollers profile throughout their life time. The final objective of the pilot project was reduce the amount of planned and unplanned downtimes of the HPGR by increasing the rollers life time and avoiding catastrophic stud damages.

Jan 1, 2018

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By R. C. Miranda

This paper intends to demonstrate the applicability of tools for advanced process control and online particle size image analysis in crushing and autogenous grinding circuits. In a crushing plant, cameras are installed in the conveyor belts of the circuit products. The vision system continuously processes the acquired images and thus obtains the variation of the size distribution curve. From these measurements, the advanced control system can operate, for example, at the opening of the crusher, in order to keep the P80 in the desired range. In addition, through the power information and level of the crusher&apos;s chamber, it is possible to increase the capacity of the crushing circuit. If the crusher is not equipped with an automatic opening adjustment, a warning may be issued to the operator to provide this setting manually. In mineral processes that use autogenous and semi-autogenous grinding for fragmentation, obtaining online F80 through the vision system allows for manipulating the parameters of rotation speed and solids concentration, through which the amount of material at the critical particle size that is produced can be controlled. In addition, the noise produced in the mill can be measured and controlled. Thus, it is possible to prevent breaches and to optimise the mill capacity for grinding. Image analysis combined with an expert system that translates this information and acts to seek the most appropriate particle size distribution, brings greater stability to the process optimising the capacity of the equipment, which allows for significant gains in production.

Sep 1, 2012

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Z. Y. Ma, M. D. Liu, Z. Z. Liu, J. K. Zhou

"An optimization method of microwave assisted leaching of copper anode slime was proposed based on Taguchi method. The results showed that the solid-liquid ratio was the most important factor affecting SNR(signal noise ratio) of the copper, tellurium and selenium leaching efficiencies, and its contributions to the copper, tellurium and selenium leaching efficiencies were 58.34%, 55.54% and 60.74%, respectively. Solid-liquid ratio was a significant factor to SNR(copper, tellurium and selenium). Reaction period was a less significant factor to SNR(copper and tellurium) and concentration of sulphuric acid was a less significant factor to SNR(selenium) while microwave power was an non-significant factor, its contributions to the copper, tellurium and selenium efficiencies were 3.22%, 11.73% and 12.73%, respectively. The optimized parameters of the microwave assisted leaching of copper were as follow: microwave power of 500 W, reaction period of 10 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The optimized parameters of the microwave assisted leaching of tellurium and selenium were as follow: microwave power of 800 W, reaction period of 15 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The validation experiments under the optimized conditions has been carried out, the copper, tellurium and selenium leaching efficiencies were 98.66%, 84.32% and 64.54%, respectively. INTRODUCTION As important valuable by-products, copper anode slimes are collected from the bottom of the electrolytic bath in the electrolytic copper refining process(Kilic, 2013). The value of the anode slime is determined by the content of rare metals and precious metals(Liu, 2014). Generally, pretreatment of copper anode slime is the first stage of the whole process. The aim of the pretreatment process is to remove Cu, Te and Se etc and enrich the valuable metals. The methods of pretreatment process can be differentiated into: pyrometallurgical processing and hydrometallurgical processing(Amer, 2003). The hydrometallurgical processes are more promising compared to pyrometallurgical processes in terms of cost effectiveness, low energy consumption and environmental concerns(Ranjbar, 2014). However, the disadvantages of the hydrometallurgy process are evident, such as lengthy processing times and low efficiency. Therefore, it is necessary to develop a highly efficient and environmentally friendly pretreatment method."

Jan 1, 2018

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Barbara Peszko, Tadeusz Tumidajski

"Various methods are used to identify the grain composition of fine-grained materials because so far the best notion of the grain size has not found and there is no single method to define grain size. In practice the most important are the following grain sizes: sieve diameter dt, effective diameter de, substitute diameter d2 and statistical diameter dst. The mentioned sizes are connected with the methods of analyses. Methods are correct but measure of different diameters of grain and their results are different.The most important methods of granulometric composition analyses are the following: the sieve analysis, the sedimentation method and the conductometric (Coulter-Counter) methods. In each of these methods various physical features connected with the grain size are measured.Sizes of grains defined by different formulas or measurement methods are associated mutually by dependencies, which are results of differences in their determination or calculation ways.In order to determine principles of results comparison the classification analysis results on linearly or non-linearly connected was made. Analyses which results demonstrate the same type of grain size distribution are treated as linearly connected. It is based on the general formulae which determines the probability density function of random variable which is the function of another random variable having the known density function.In order to show the difference in the grain composition of the same material qualified by different methods, three methods of investigations were distinguished. They are: the sieve analysis performed on precise sieves, the sedimentation analysis performed by means of a sedimentation balance “Sartorius” and the microscopic analysis performed after preparing a microscopic slide where the grain size was measured by the Martin’s method.The materials selected for the analysis were quartzite and glass, which are the material of high purity.The obtained results of mentioned above three types of analyses were approximated by distribution function of four distributions: Weibull, log-normal, cut Weibull and Gaudin-Schuhman."

Jan 1, 2003

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

"The most common agglomeration technique in iron and steelmaking is sintering, which requires the use of iron ore/concentrate mixtures, limestone and dolomite as fluxes and coke as fuel in order to produce the required melt at high temperature to cause agglomeration of the particles. Sinter feed blends containing high proportions of magnetite concentrate are difficult to granulate and to produce granules of high permeability, and sufficiently robust quasi-particles for successful sintering operations. Since the granulation of iron ore sinter feed requires no use of a binder, the added fluxes play a vital role in holding the granule particles together until they sinter. The fluxes also help to improve the granule quality and control slag composition in the blast furnace. It is well-known that the particle size distribution of the fluxes affects the granulation effectiveness and green bed permeability which determine the productivity, physical and metallurgical properties of the granules and sinter. Hence it is necessary to understand the role of flux particle size on granule properties so as to improve the granulation of iron ore sinter feed blends containing high magnetite concentrate. In this study, laboratory granulation experiments have been carried out on iron ore sinter feed blends containing high proportions of magnetite concentrate at different addition levels of limestone and dolomite mean particle sizes, to understand the influence of limestone and dolomite particle sizes on granulation rate processes and granule properties.INTRODUCTION Increases in iron ore production to meet the global demand for iron and steel products has led to the depletion of high grade iron ores and thus the current utilisation of low grade iron ore fines and concentrates. However, sinter, pellets and the lump are the required feed types used in the blast furnace. The high basicity sinter is the main iron bearing feed accounting for 70-85% in the blast furnace due to its good metallurgical and mechanical properties that allow high productivity, efficient processes and low production cost (Adam et al., 2017)."

Jan 1, 2018

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003