Search Documents

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By L. Rintala

The design of a hydrometallurgical process starts with the analysis of the raw materials to be treated, for example mineralogy, chemistry, deposit size are analysed. Based on this information suitable unit processes for pre-treatment, leaching, solution purification and product recovery are selected. Typically, process design for the new ore deposit relies on laboratory tests such as pre-treatment and leaching experiments. The experimental work is the most time consuming and expensive part of the process design. Reducing the number of experiments would shorten the time of designing a new flowsheet or development of new process technology. A large amount of information is available about the hydrometallurgical experiments and the amount is increasing continuously. For example, word search using ?hydrometallurgy? from Scopus database results in over 4 000 publications with the word in title, abstract or keywords. This number consists of 2 500 articles, 900 conference papers, and 90 reviews since 1972. The number of hydrometallurgical publications per year has increased from 13 in 1972 to 150-200 in the last few years. The objective of this study was to analyze how detailed data of experiments about the gold extraction is published and how that data could be exploited more effectively when designing hydrometallurgical processing for new ore. The leading idea is that similar ores should have the similar response in leaching. If the published information was used more efficiently, the amount of experiments would be reduced. More than 200 cases of experimental data of gold leaching have been analyzed for this study. There are over 30 factors that could be used in comparison when selecting process alternatives, but challenging fact is that not all these factors are documented in all publications. Results show that the usefulness of the published data in the development of hydrometallurgical flow sheet for gold using decision-support tools is not that straightforward. The quality of the published information about gold extraction varied between the publications and the descriptions of the raw materials, experimental arrangements and results were often missing details. Methods to normalize the data for description of the cases and a system to describe different features unambiguously are needed. Keywords: refractory gold, host mineral, leaching, data analysis, case-based reasoning

Sep 1, 2012

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By Mike Daniel, Eric Wang

"Several new large copper and gold concentrators have been built and commissioned around the world in the past five to eight years. The success of the ramp-up from these very large concentrators has varied. CITIC SMCC Process Technology was engaged to assist some of these mines by gaining a better understanding of the factors that influence throughput capacity. As such, site-specific throughput forecast models that are influenced by SAG mill performance were developed. The forecast models are easy to interpret and modify and can greatly assist the mine management to make predictions and informed decisions for a range of site improvements. The models investigate the influence of SAG mill performance with respect to ore competency, derived from SMC Test® via the measured DWi model parameter. In some cases the benefits of blasting and from fine tuning milling operations are already incorporated into the "site-specific" forecast models. The methodology follows rigorous plant data analysis that is analogous to a "Mine-to-Mill®" optimisation project. The CITIC-SMCC model validation includes extensive data collection, which includes drill core analysis, ore characterisation and comprehensive comminution circuit operational data to assess the limitations within the comminution circuit within the operating mine. The results and models may be used to define the operating base lines of the processing areas and identify improvement opportunities upstream and downstream of the comminution circuit. The predictive capability of the models use logged production data and has enabled the user to differentiate between alternative circuit configuration options and identify optimum operating conditions. This approach minimises the ongoing requirement for costly plant surveys. The improvement strategy for each site, included the ongoing measurement of grindability, rock strength and via the Bond and SMC Test® respectively. Some commentary as to what other practitioners do with input data and their models is also presented as this highlights some of their shortcomings relative to the CITIC-SMCC methods."

Jan 1, 2014

By M. Guo

Coal-based Direct Reduction in Interior-combustion Shaft Kiln (CDR/ISK) is a brand-new technique. Compared with the traditional Coal-based Direct Reduction (CDR) technique, its main character is to use Interior-combustion Shaft Kiln (ISK) as the reactor of direct reduction. After being crushed and grinded, iron ore is made into green pellet, which will be surface-coated by coal fines. Then, the surface-coated green pellet can be directly reduced in ISK. The pellet should not be too dry and should be charged from the top of ISK. Oxygen-contained air should be blasted into ISK to keep the temperature in it higher than 1000 degrees centigrade, at which iron oxide will start direct reduction. The reduced pellet will be discharged from the bottom of ISK and after de-surface-coated, spherical Direct Reduced Iron (DRI) can be gained. The volume of carbon monoxide in the off-gas discharged from ISK is less than one per cent. By using this technique to get one tonne DRI, the consumption of coal is about 300kg of fixed carbon, which is much lower than the energy consumption by using other CDR techniques. There is a lot of complex refractory iron ore in China, which remains unexploited. The iron-bearing minerals in this kind of the iron ore can not be beneficiated economically by present technique of gravity, magnetic, flotation or magnetic roasting because the iron minerals are too very finely disseminated to be liberated, or, the iron minerals are too similar to gangue to be separated each other. By using CDR/ISK, complex refractory iron ore can be directly reduced in lower temperature and all kinds of iron mineral can be turned into iron metal. As the grains of iron metal growing larger during direct reduction, magnetic separation can be used to separate iron metal from gangue mineral, thus high-grade iron metal fines can be gained. According to the experiments, the grade of iron metal fines is above 90 percent and the recovery of iron is higher than 90 percent. The consumption of coal to process one tonne of complex refractory iron ore is only about 90kg of fixed carbon.

Jan 1, 2014

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014

By Al Cropp, Julie Hunt, Will Goodall, Ron Berry, Dee Bradshaw

Geometallurgy aids the understanding of ore body variability but has the most value if the data is easily available along the entire mining value chain. This requires cross-discipline communication and collaboration across traditional silos, and an organizational culture that encourages that to flourish. Data that are collected by the numerous groups (i.e. mining, geology, milling, processing, refining, smelting, marketing, environmental etc.) involved in the mining process may have relevance to other stakeholders; mineralogical and textural data for example has value to all these groups. Data required for modeling comminution or identifying acid potential from waste rock may already exist, however it needs to be made available to all the relevant stakeholders in the right format at the right time. As part of the GeM (AMIRA P843 & P843A) project the opportunity has been taken during the sponsor meetings, short courses, case studies etc. to ask the question: ‚What information do you want from further up the chain?? For example, to metallurgists ‚What information would you like from the geology group before the ore enters the mill?? The geology group may already have information important to mineral processing but not know it is of interest. This could, for example, be in the form of a geometallurgical drill core log that contains quantitative measured values. This paper focuses on the interaction between the mining, geology, mineral processing and environmental groups, using ore properties resulting from geological alteration to identify potential impacts throughout the mining process and discusses how a cross discipline approach can benefit all.

Jan 1, 2014

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By Luis Bergh, Iván Rojas, Juan Yianatos, Luis Vinnett

"At present, flotation rate characterization follows standard measurements to identify the overall flotation performance looking at the feed, tailings and concentrate in flotation cells or banks. This classical approach does not take into account the evolution of the true collection rate down the flotation banks explicitly. The potential for identifying the impact of the mineral characteristics (size and liberation) as well as the effect of different manipulated variables (reagents, froth depth, gas dispersion) on the true flotation process remains hindered. Top-of-froth (TOF) measurements, which consist of sampling the first layer on the froth surface, have been used to characterize the mineral collected by true flotation in rougher banks. The information provided by TOF samples allows evaluating the floatable mineral evolution (grade, particle size, liberation) down the bank. In this work, an indirect approach to estimate the flotation rate along rougher flotation banks is proposed. The new approach is based on the decreasing of collected mineral grades (on top of froth) and the feed characteristics. Flotation rates per liberation classes were used to reconstruct the TOF grades from the feed information. This approach requires a simple froth surface sampling, without constraints typically observed during mass balance surveys and uncertainties on the mineral recovery estimation. The proposed methodology was successfully applied at industrial scale using TOF measurements together with QEMSCAN information."

Jan 1, 2014

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By Jan Cilliers

The demand for minerals has never been higher. Moreover, the rate at which this demand is growing is unprecedented, and expansions and new mines will be required to fulfill these growing needs. This, in turn requires a skilled engineering workforce that can develop and operate minerals extraction processes to utilise effectively more complex ores. The International Mineral Processing Council (IMPC) has established a Commission on Mineral Processing Education to consider the global challenge of ensuring an adequate supply of well-trained mineral processing engineers. The Commission has, for the past four years, been collecting international information of the recent mineral process engineering supply position and with a view into the near future. The data collected by the international Commission members are as follows: ? Undergraduate student numbers in minerals engineering ? A breakdown of their male/female ratio ? The fraction of the students from each course that enter the minerals industry ? Teaching staff numbers and age profile This data has been collated and analysed, and the findings are presented. It is clear from the analysis that the supply situation is very different in different regions of the world, and that great opportunities exist for targeted recruitment into the industry to meet the future talent demand. Further, an attempt at correlate the supply of minerals engineers based on the local mineral production rate is shown, which shows that there are clear outliers.

Sep 1, 2012

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By Ji Hoe Kwon

Hindered-settling column process has been used for the separation of mineral particles for many years. In this study, a model based on DEM (Discrete Element Method) was used to simulate the movements of particles in a settling column separation process. DEM model is capable of describing the motion of particles and calculating the impact forces between particle and particle, and particle and wall contact under various operating conditions. Drag force, rotation induced Magnus lift force, contact force and the gravitational force acting on individual particles were considered for establishing the mathematic models. The overall motion of the particles in water is satisfactorily simulated by the DEM, and the result shows good agreements with the result of lap-scale experiment.

Jan 1, 2014

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014