Search Documents

By Robert van Hille, Alison Lewis

The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pre-treatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium. The pellet reactor was used to precipitate nickel as nickel carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed. For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. For removal of cobalt as cobalt carbonate from an actual stream, a stable cobalt removal of only 60% was achieved. This was found to be due to the presence of magnesium, which reduced the cobalt precipitation efficiency through the formation of the magnesium bicarbonate ion.

Jan 1, 2003

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By Venkata S. Buddhiraju

Pelletization of iron ores involves balling on a rotating disc to produce wet pellets and induration of wet pellets on a moving grate to produce fired pellets. The quality of pellets produced and the productivity of the pelletization process depend strongly on the characteristics of the feed to the pelletization disc, especially the particle size distribution and the moisture content. The upstream processes involved in the preparation of pelletization feed include grinding, thickening and filtration of the iron ore slurry. The focus of the present work is the closed circuit wet grinding of iron ores. The circuit consists of a primary ball mill, a regrind mill and a hydrocyclone. A population balance model was developed to predict the grinding kinetics and an empirical model was fitted for the separation of fine particles from the coarse particles in the hydrocyclone. Batch grinding kinetics experiments were performed on a laboratory scale ball mill to obtain the ore breakage parameters which were subsequently used for the simulation of the industrial mills. The models were customized for the industrial operations and the effects of different process variables like feed flow rate, water flow rate, etc., on the size distribution of product from the grinding circuit were studied. Additionally, different circuit configurations were simulated to determine operating conditions that could result in the desirable product particle size distribution. The results of simulation were in close agreement with plant observations and the new circuits explored through simulation have helped in identifying potential opportunities for process optimization and control

Sep 1, 2012

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014

By Li Maolin, Cui Rui, Wang Guanghui

"As the stirrer speed directly affects the motion of grinding media, and hence the interactions with material particles to be ground, the rotation speed of a stirred mill is well recognized as one of the most important factors affecting the grinding performance. In this work, the effect of stirrer speed on grinding performance in terms of grinding rate and grinding energy efficiency was quantitatively investigated. Batch wet grinding tests of quartz powder at different stirrer speeds were performed, using a self-made horizontal stirred mill with alumina balls as grinding media. Grinding time, operating power and the sizes of ground product were recorded to analyse the grinding performance. The test results showed that grinding processes followed the first order grinding kinetics. The grinding rate constant increased with the increasing stirrer speed. Based on the grinding kinetics, the grinding energy equation was established. The energy utilization coefficient in the energy equation can be used as an indicator of energy efficiency. The energy efficiency decreased with the increasing stirrer speed. Quantitatively, with the stirrer tip speed increasing from 4.25m/s to 9.35m/s, the grinding rate constant was improved by 441.47%, whereas the energy utilization coefficient was decreased by 39.35%. The grinding rate constant and energy utilization coefficient can be used to evaluate the grinding performance when the grinding conditions need to be adjusted. The adjustment of grinding conditons would be optimal when grinding rate get significant improved with little decrease of energy efficiency."

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By Smuts. E. M.

This paper describes a methodology used to develop a numerical model for the study of particulate suspension rheology. Initially, Computational Fluid Dynamics (CFD) models of different rheometer geometries were tested with both a Newtonian fluid (water), and a non-Newtonian Herschel-Bulkley slurry. Rheograms were reproduced from these models and compared to experimental values. Once a single-phase model had been validated, a coupled model combining CFD and the Discrete Element Method (DEM) was created. Two open source software packages were chosen. CFD is implemented using Open FOAM®, and DEM using LIGGGHTS. These two different codes were coupled via another program called CFDEM. This coupled model is currently capable of modeling spherical particles in a suspending liquid. DLVO forces have been included in some models to account for inter-particle forces due to the surface charge on the particles. The coupled model is currently being validated. Preliminary results show good qualitative behavior of the model. Keywords: rheology, cfd, dem, suspensions, modeling

Sep 1, 2012

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Hoon Lee

Laboratory tests were conducted to evaluate the breakage characteristics of pyrophyllite in a laboratory ball mill. In grinding tests, the breakage characteristics were analyzed using the mathematical kinetic models based on the two breakage functions; the specific rate of breakage and the primary breakage distribution. Two samples having similar chemical composition show identical values in specific rate of breakage. In comparison, there are different values of primary breakage distribution for each sample. The size distributions of the product with various grinding time are well described by the parameters from non-linear searching.

Sep 1, 2012

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014

By C. S. Gundewar

About 90% of the barytes produced the world over is used for oil and gas drilling as weighting agent in drilling mud to control pressure, prevent blow out and provide lubrication. This is because of its unique properties like high specific gravity, water insolubility and intentness. India is one of the leading producers and exporters of barites. The Mangampeth Baryte deposit in Cuddapah district of Andhra Pradesh, India being the largest single deposit in the world having a reserves of about 80 million tonnes. Approximately 50% of the total reserves of grey barites of Mangampet deposit assays less than 92% BaSO4, the minimum stipulated grade for oil and gas drilling industries. To reach and recover the high grade barite, the overlying low grade has necessarily to be mined out and removed. At present this is being stacked separately at the mine site involving lot of labour and transport cost. Considerable barites is contained in the dumps adversely affecting the conservation and creating lot of environmental hazards. IBM being the premier organization in India in the field of conservation of minerals and environmental protection in mining has recognized the importance of adverse effect of these huge dumps at site. The Ore Dressing Division of IBM, Nagpur has characterized these dumps and developed the flotation process on a sample assaying 66% BaSO4 and 23.3% SiO2. The flotation concentrate obtained assayed 93.7% BaSO4, 2.38% SiO2 with BaSO4 recovery of 80% and meets the requirement of the oil industry. The flotation concentrate being non-wetable, can not be used as such as weighting agent, and hence the collector coating on the concentrate was removed either by acid treatment or heating to make it water wetable. The concentrate was 92% -325 mesh and having a specific gravity 4.3. The barites concentrates so produced meets the size, grade and specific gravity specifications required for use in oil drilling industry. Apart from the financial benefits the process augurs well for the commercial exploitation of these huge dumps in terms of (1) additional recovery of these valuable minerals and conservation, (2) reduction in dumps value, (3) improvement in environment and offering an excellent potential for export.

Jan 1, 2014

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

By X. Y. Zeng

Most Chinese titanium bearing minerals are the composition of magnetite vanadium and ilmenite. All of such mineral processing plants use low intensity magnetic separators to recover magnetite and vanadium goes with magnetite. In the past years most of the plant tails containing about 10% TiO2 were abandoned. Now many of these plants use SLon magnetic separators to recover ilmenite in the roughing stage, which can throw away most of the gangs and slimes with very low cost. The new development of applications of SLon magnetic separators in Chinese ilmenite processing industry is introduced in the paper.

Jan 1, 2014