Search Documents

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By M. P. Krasteva

The froth flotation process for separation of mineral ores depends on the establishment of care-fully controlled froth. The formation of very stable froth in the flotation circuit is a problem that may occur in many plants, resulting in down-time, low quality and grade of final product and considerable expenses. Froths build up on the top surfaces of thickeners, tanks and flotation cells until they overflow, or until the efficiency of the circuit is impaired. A similar problem exists in Assarel concentrator, Assarel-Medet PLC, Bulgaria. Copper and copper-pyrite ores are dressed in Assarel concentrator. They are characterized with variable and complex mineral and physical composition. During the flotation cycle, resilient and difficult to break-down froth is formed, which subsequently impedes the process of thickening and clear overflow obtaining. Due to this problem continuous sampling in the cycle of thickening was conducted. The mineralogical, chemical composition, particle size distribution and solid phase content of the products were determined. It was established that the solid phase of the froth build up on the top surface of the thickener differs considerably from this one of the thickener underflow. The data clearly indicates that a separation process takes place on the top surface of the thickener ? fine particles of chalcopyrite are concentrated in the froth. The role of chemical reagent addition in the break-down of the flotation froth is investigated in terms of surface chemical phenomena involved in the stabilized froths. Measurements of the coper minerals wettability and surface tension at the air/liquid interface were performed. The surface active agent AERODRI® dewatering aids were laboratory tested. Bench-scale froth collapse tests were conducted. Reagent addition into pulp-froth system promotes and leads to a bubble coalescence, an improvement of the wetting of the mineral particles and a decrease of the surface tension at the air/liquid interface. The results of the laboratory experiments showed that the presence of the surface active agent leads to considerably decrease of the froth stability and the destruction of the deleterious froths build up on the top surface of the thickeners in Assarel concentrator.

Jan 1, 2014

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By N. I. Um

The coal bottom ash generated from coal-fired power plant accounted for approximately 5 mil-lion tons in Korea. Almost all of coal bottom ash was treated as reclamation of the landfill because of the content of unburned carbon. For recycling of coal bottom ash, effective removal of that is required. So, in this study, the removal of unburned carbon by flotation was studied with respect to adsorption ability in surface of a bubble in order to consider its application to recycle the coal bottom ash. The sample A, B and C were that the coal bottom ash contained 2.73%, 7.01% and 10.49% of the unburned carbon (UC) respectively. The column flotation was carried out for each time as the artificial injection of air at 10.0L/min flow rate and the reagents of 500g/ton kerosene and 80g/ton MIBC were used. The samples per water of 1.3 liters were from 0.5% to 4% (w/w.%). In the result of this study, the kinetic curves of unburned carbon adsorption from injected air bubbles were in-creased rapidly as equilibrium was approached; only 5 sec was needed from the sample A and B and 10 sec was from sample C. And the equilibrium isotherms of unburned carbon adsorbed by the infected air bubble from the sample B and C could appear the BET adsorption isotherm; MT = KMEEO/(EO-E)[EO+(K-1)E](K: adsorption affinity), but not the sample A that was not enough to express the adsorption curve.

Jan 1, 2014

By V. E. Dementiev, V. I. Kulikov, G. I. Voiloshnikov, Yu. O. Fedorov

"The report presents the summary of the JSC Irgiredmet’s activities in the field of preconcentration of ores. As of 2018, the Institute has almost 40-years’ experience in this area. Over the years, Irgiredmet has done a lot of work – from development to implementation of new technologies of ore piece sorting and concentration based on X-ray radiometric separation (XRRS). INTRODUCTION Preconcentration has been a challenging issue of the mining industry over the last decades. The implementation of this technology can significantly increase mining efficiency. The main application of preconcentration is improvement of mined ores quality, however new and more complex issues have arisen with the evolution of the technology. Irgiredmet has started to develop an efficient preconcentration technology for gold-bearing and rare-metal ores 40 years ago. The X-ray radiometric method widely used at that date as a method of elements determination in geology and geophysics become the ground for this work (1). Since that time, the Irgiredmet Institute has developed and significantly improved the technology of piece ore sorting, or XRRS (2-5), that is currently also known as the X-ray fluorescence method. The progress of the XRRS development achieved by Irgiredmet in cooperation with Rados LLC, Tekhnoros LLC (Krasnoyarsk), Rados-Service LLC and CJSC Tekhnogen (Ekaterinburg) has proved efficiency and applicability of the XRRS technology for processing a wide range of minerals and solving of various technological problems (7-9) compared to other radiometric methods (6). Furthermore, obtained results are supported by numerous studies, trials and implementations. The significance of ore preconcentration for greenfield and brownfield projects determined the establishing a new subdivision of Irgiredmet, the XRRS Technology Center (XRRS TC), that has provided the Institute with a completed range of processing technologies, from preconcentration to producing final products. Over the past few years, the XRRS Technology Center has carried out studies and testing of a numerous (more than 100) projects, mines and deposits of gold-bearing ores, rare metal ores (Be, Ta, Nb, W, Mo), base metal ores (Cu, Sb, Zn, Pb), ferrous metal ores (Fe, Ti, Cr), rough diamonds and coal. The XRRS Technology Center performs various specific studies and testing not only in Russia, but as well as in Kazakhstan, Georgia and Mongolia. Mines and companies from Chile, India, China, Iran and other countries also take an active interest in the XRRS technology."

Jan 1, 2018

By Shuji Owada, Shinya Suzuki, Chiharu Tokoro, Daisuke Haraguchi, Sayaka Izawa

"Coprecipitation with ferrihydrite has been one of the major treatment method for As(V) removal from wastewater such as acid mine drainage. We already confirmed coprecipitation of As(V) with ferrihydrite consists of two kinds of mechanism; one is two dimensional As(V) uptake to the surface of ferrihydrite by surface complexation and another is three dimensional As(V) uptake into ferrihydrite by surface precipitation. We also already confirmed As(V) adsorption process by ferrihydrite could be quantitatively evaluated by original surface complexation model with parameter values reported by Dzombak and Morel. However, As(V) coprecipitation process couldn’t quantitatively be represented by only the original model. In this study, construction and calculation using surface precipitation model were attempted for As(V) coprecipitation treatment with ferrihydrite. In the surface precipitation model, precipitation was described by the formation of solid compound between ferrihydrite and ferric arsenate. Activity of these precipitates was determined by surface precipitation ratio of FeAsO4(s) obtained experimentally from XANES analyses. Solubility products of surface precipitation of FeAsO4(s) (Ksp_FeAsO4(suf.)) were determined by fitting to sorption densities and surface precipitation ratio in each condition. The values of Ksp_FeAsO4(suf.) were determined 10-7.7 at pH5 and 10-10.2 at pH7, respectively. Based on the obtained Ksp_FeAsO4(suf.) value, As(V) removal and isotherm were calculated for As(V) co-precipitation treatment using surface precipitation model. Good agreement between experimental and calculated values was observed. These results were suggested that the quantitative prediction of As(V) co-precipitation treatment was possible if Ksp_FeAsO4(suf.) value was estimated experimentally."

Jan 1, 2014

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work."

Jan 1, 2003

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By P. T. L. Koh

The effect of particle shape on the flotation process has been investigated in laboratory experiments with monosized spherical ballotini and roughly ground ballotini. The particles were treated by partial methylation with trimethylchlorosilane to achieve varying degrees of hydrophobicity. In flotation, the process of film thinning and liquid drainage is critical in the formation of a stable bubble-particle attachment and this is affected by the particle shape and surface hydrophobicity. The rate of attachment affects the overall flotation rate. Flotation tests with different particle sizes at various degrees of partial methylation have been performed in a modified Denver cell. Predictions from a computational fluid dynamic model of the cell which incorporates fundamental aspects of bubble-particle attachment are compared against flotation test results. Contact angles of the particles have also been measured using the capillary rise technique to indicate surface hydrophobicity.

Jan 1, 2014

By M. Pelser, C Aldrich

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.Several processes are reviewed for the control of calcium and magnesium. Of these, fluoride precipitation was selected for experimental investigation. This method involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments showed high selectivity for calcium and magnesium over the base metals. The experiments also showed magnesium precipitation to dominate for calcium to magnesium molar ratios greater than 1:3.To avoid the domination of magnesium precipitation, a flow sheet is proposed whereby only a portion of the base metal stream is subjected to fluoride precipitation. For the precipitation, a 10% excess of ammonium fluoride is used to remove the maximum amount of calcium and magnesium. After precipitation and solid-liquid separation the split-stream is returned to reduce the overall calcium and magnesium concentration of the base metal stream."

Jan 1, 2003

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

By Lev Filippov, Lorène Dessalas, Inna Filippova, Yves Foucquet

"Seafloor massive sulphide (SMS) deposits, similar in composition and genesis to terrestrial volcanogenic massive sulphide deposits, are generally found in volcanic seafloor environments along major rifts and mid-ocean ridges. Theyare associated to extensional tectonic settings such as nascent-arc, rifted-arc and back-arc environments. They may represent important source of base metals and be an alternative to on-land resources. Seafloor massive sulphide deposits have particular mineralogical compositions and textural features differentiating them from terrestrial one. When extracted from salty water and exposed to the ambient air, massive sulphide samples strongly oxidize and soon become covered by thin layers of iron, copper and zinc rich sulphates and oxides, as well as elemental sulphur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. The total porosity of that type of samples is also relatively high, especially for immature samples such as black smoker chimneys, which can reach 15% of total porosity. Because the secondary mineralization and porosity level are different, seafloor massive sulphides ores respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all type of sulphides from the gangue, is one possible technique for processing seafloor ore. Sulphide recovery rate is, in most cases, excellent (>90%) however separation of the various mineral phases is difficult to obtain even when applying known methods used for terrestrial ore. Moreover, the flotation behaviour decreases drastically with the time of conservation at the surface, even when the samples were stored in a confined environment. High pH values, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulphides, do not have the same effect on seafloor ore. Consequently, careful flotation procedure must be elaborated to obtain efficient mineral separation technique for this specific marine ores."

Jan 1, 2014

By A. S. Choudhary

India is endowed with a reasonably large reserve of chrome ore, amounting to about 100 million tons in different grades and is one of the leading producers of ore/concentrate along with South Africa, Kazakhstan and others. Chromite production in India has registered a 10 times increase during the last 30 years. Till late 1940s, the practice was to mine the high-grade ore for making ferrochrome and charge chrome and export the same leaving the low and medium grade ores stacked around the mine as waste material. This practice was continued for quite some time till the increase in world wide de-mand of chromite initiated an increase in production of chromite ore in India and the aspects of ?economy of operation? and ?conservation of mineral? dawned on the producers and associated authorities. Recovery of chrome values from low and medium grade ore was initiated to produce high-grade saleable concentrate. Suitable legislation was made by Government of India to induce and provide incentives to the operators to do so. First large scale chromite beneficiation plant in India was commissioned about three decades back at Byrapore in the Southern state of Karnataka. The ore, rather simple in nature and relatively free from clay, was obtained from underground. The processing consequently was simple washing and wet tabling. Further more, some test work, on the samples from eastern coast particularly from Orissa, was carried out at an internationally reputed laboratory by a large private operator and the plant was set up. This consisted of a combination of crushing-grinding-de-sliming-classification followed by concentration in multi stage spiral concentrators and shaking table. The plant was commissioned and operated successfully. Soon a state owned company followed suit on the basis of test work carried out in a well equipped Indian laboratory. The plant worked satisfactorily after some initial teething trouble and the company plans to double the existing plant capacity by installing balancing facilities. This development prompted a number of operators, including industry leaders to join the fray and the chrome ore processing industry flourished in India. More and more operators are now in the process of adding capacities to their existing plants. This paper attempts to chart the evolution of chrome ore beneficiation industry in India through a case study with reference to an existing plant. The process technology adopted and modified to suit the altered requirements as well as the future trends are outlined.

Jan 1, 2014

By J. Gong

Fine mineral particles pose two challenging problems in froth flotation, i.e., ineffective recovery of fine hydrophobic particles and mechanical entrainment of fine hydrophilic particles. The first problem has attracted much research effort while the second problem has received much less attention. We have recently proposed a method to deal with mechanical entrainment, i.e., utilizing the flocculating power of polymeric depressants to flocculate fine gangue particles and making the flocs big enough so that the mechanical entrainment of these particles can be reduced or eliminated. In this paper, we report results on the use of polyethylene oxide (PEO) in controlling quartz gangue in the flotation of sulphide ores. PEO was found to flocculate fine quartz and lower its entrainment. It was also found to modify air/water interfacial properties and acted as a frother, which could increase gangue entrainment. Nevertheless, when used at starvation dosages, PEO was found to significantly improve the grades of the floated sulphide concentrates.

Jan 1, 2014

Cenospheres is a sandlike hollow sphere component of the fly ash that is collected in coal-burning electric power generating plants. Metal coated particles have been widely used in industries. Magnetron sputtering method which was used to coat copper film on the surface of the cenospheres is a widely used coating technique in large surface metal coating. A newly designed equipment is used to make the fine particle coating can be carried out because the fine particle is hard to disperse and it must make the particle keep moving to let every direction of the particle be coated. The copper film coated is compact, smooth, even and without uncoated spots under the optical microscopy and SEM. The film has good affinity to the cenosphere surface. The film does not separate with cenoshpere surface even when the cenosphere is crushed. The XRD, SEM, XPS, SPM was used to study the copper film characteristic. It is shown that using this newly designed magnetic sputtering equipment can coat high quality copper nanofilm on the cenoshpere surface.

Jan 1, 2014