Search Documents

By T. Fujita

The incinerated bottom ash includes titanium oxides and a small amount of chromium oxides. Initially, 89 % of chromium was removed from ash at magnetic flux density at several stages of wet magnetic separation from 0.05 T to 6 T. The bottom ash from an industrial waste incineration process includes about 10 % of TiO2. The minerals that contain titanium are rutile and perovskite. These minerals are paramagnetic and show low magnetic susceptibility, therefore, the high magnetic field strength, created by a superconducting magnet, is necessary to capture these minerals. At the first stage of separation, a magnetic field strength of 6T was applied in order to attract the particles that contain iron oxides to the higher magnetic field region. At the second stage of separation, the magnetic capture rate of weekly magnetic particles decreased with increasing the magnetic susceptibility of the aqueous solution (i.e. the medium for dispersing the particles) in order to separate the highly magnetic materials. The para-magnetic salt such as ferric chloride was dissolved in the water to increase the magnetic susceptibility of the medium. After a two-step wet HGMS with superconducting magnet, the grade of TiO2was increased from 10 % to 28 % with a recovery of 64 %.

Jan 1, 2014

The air recovery from a flotation cell is the fraction of inlet air which overflows the weir as un-broken bubbles. The air recovery is an important factor in froth phase phenomena; such as gangue entrainment and froth recovery. Increasing the air recovery, results in a higher recovery of attached mineral particles. Air recovery can be measured experimentally on plant using image processing of the top surface of an overflowing froth. The air recovery is directly linked to froth stability and the bursting rate of the bubbles at the froth surface, making it very difficult to predict. Experimental results show a very strong correlation between the superficial velocity of the inlet air and the superficial velocity of the air leaving the cell through the froth surface due to bursting, calculated from the experimentally measured air recovery. This correlation holds over multiple banks from different plants. Development of a power law equation around the inlet air velocity and the bubble solids loading on the froth surface allows the superficial air velocity through the top surface of the froth to be predicted, and from this the air recovery. This model is valid for use when operating beyond the peak in air recovery.

Jan 1, 2014

By M. V. Sowmya

Batch biosorption experiments were carried out for the bio-remediation of Cr (VI) ions from aqueous solutions using Serratia marcescens, a Gram negative, heterotroph and Gram positive bacterial isolates from a chromite mine. The influence of various experimental parameters such as contact time, pH, concentration of Cr (VI) ions and amount of biomass was evaluated with respect to the uptake of Cr (VI). The bio-sorption of Cr (VI) was found to be quite rapid and the percentage biosortion was found to increase with increase in the equilibrium chromium concentration. The free energy of biosorption of Cr (VI) was estimated to be in the range of -23 to -25 kJ/mol for the chosen bacteria. The uptake of chromium by the bacteria was confirmed by EDX and FTIR spectroscopy. As a follow up of this study, bacterial strains resistant to hexavalent chromium were isolated from a chromite mine in Karnataka, India and identified as Arthrobacter sp., Micrococcus sp. and Exiguobacterium sp. using 16s rRNA sequencing. The efficacy of the bacterial isolates for Cr (VI) uptake was assessed and over 90% bioremoval could be achieved for Serratia marcescens and Micrococcus sp. isolate. Possible mechanisms of chromium uptake by the microorganism are discussed. Keywords: bioremediation, hexavalent chromium, biosorption, bioreduction

Sep 1, 2012

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By B. A. Kutlin

29% of the total ore mined in the Russian Federation for copper production is finely disseminated copper-zinc-pyrite ores of the Ural Region. Physical and chemical characteristics of pyrite copper-zinc ores make for difficulties in obtaining high indices during processing. At present, the authors have elaborated the technology to improve the quality of copper concentrates up to 20.0% for the ones obtained during pyrite copper-zinc ore processing (based on the example of the ore mining and processing enterprise ?Uchalinsky GOK?, Russian Federation). There are examples of use of fair-sized pneumo-mechanical flotation machines by modernization of processing plants. Keywords: copper-zinc-pyrite ores, Ural region Russian, selective flotation, pneumo- mechanical flotation machines

Sep 1, 2012

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By V. V. Zakopaylo, M. V. Lukyantseva, V. A. Ignatkina, V. A. Bocharov, L. C. Khachatryan, D. M. Altynamanov, A. A. Kayumov, R. H. Sharipov

"This research was aimed to explain the reasons of low floatability of tennantite from refractory pyrite ores of non-ferrous metals and to create a reagent regime for selective increasing a recovery of copper sulfide minerals from arsenic-containing copper pyrite ore. ?opper-zinc ore of the Uzelga deposit has 89% of pyrite, some part as melnikovite; copper is assayed as 3.58% of tennantite and 0.25% of chalcopyrite; there is 2.19% sphalerite. Sulfide minerals are very finely disseminated. Tennantite is genetically related to primary copper sulfides. Graphene was identified on the surface of tennantite by a transmission electron microscopy (TEM) method. The recovery of tennantite was rose up by using the collector M-TF. M-TF is the mixture of diisobutylditiophosphate (DTF) and O-isopropyl-N-methyl (ethyl) (TC) in the certain ratio. M-TF change up a kinetic of copper sulfide flotation in a slightly alkaline medium, but pyrite has slowly floatability at this moment. A depressing effect of thiosulfate ions in a liquid phase of pulp flotation tennantite from pyrite ore has been established. A copper recovery up 14.2% (from 67.7 to 82.0%) into a copper concentrate level off copper grade of 18.65% (butkx) and 18.68% (M-TF) has been increased by the new technology with M-TF compared to a standard technology with butkx. A main copper recovery up to 50 % in an inter-cycle copper concentrate assaying 19-21% Cu in case of using M-TF was gotten. A zinc concentrate with recovery of 50% and a zinc assay of 41.76% by a standard flow sheet with butyl xanthate was obtained. A zinc recovery of 70.3% with a zinc grade of 44.17% by the M-TF technology was achieved.INTRODUCTION The pyrite copper-zinc ores of the Urals region are considered refractory. The distinctive features of these ores include a high content of pyrite (90-95%), the presence of arsenopyrite and arsenical pyrite, and the simultaneous presence of chalcopyrite, bornite, tennantite with the predominance of the latter (Andreasen et al.,2008;.Dobrotsvetov, 2009; Chanturiya et al. 2016). The flotation properties of tennantite differ from those of chalcopyrite (Xumeng Chen, Yongjun Peng, Dee Bradshaw. 2014), which is the reason why a comprehensive study was under taken of the flotation activity of tennantite and a process for its recovery was developed. The proposed agent treatment and flotation process make it possible to produce salable copper and zinc concentrates."

Jan 1, 2018

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By U. Dmitrakova, G. Sedelnikova, D. Kim, E. Savari

"The paper presents the results of research on the development of gold and silver extraction technology from refractory gold sulphide flotation concentrate of one deposits of Nord-East of Russia. The concentrate is due to the complex mineral composition. Gold and silver are finely disseminated in sulphide minerals (arsenopyrite and pyrite partially oxidized by 7-11%). These are characterized by high content of silver 219 g/t and sulphide sulfur 32%, the presence of poorly soluble silver minerals (silver sulfosalts, fahlore, finely dispersed hypergenic acanthite in iron hydroxides and jarosite, etc.), and impurity minerals capable of interacting with cyanide (pyrrhotite, marcasite, nonferrous sulphides) and causing higher than normal cyanide consumption. Pretreatment of refractory sulphide concentrate by biooxidation using a mixed association of mesophilic and moderately thermophilic bacteria at a temperature of 36-40 °C for 120 hours oxidized arsenopyrite by 97.5%, pyrite by 93.5%, unlocked refractory gold, and generally oxidized the minerals absorbing cyanide and oxygen before cyanidation. Further oxidation of these minerals-absorbents was facilitated by the aeration in calcareous medium of the solid biooxidation residues of the concentrate. Sorption cyanidation of the solid biooxidation residues with addition of lead (II) of recovered 91.2% of gold and 82.9% silver from biooxidation residue, compared with 80.1% and 46.6%, respectively, for sorption cyanidation without the preceding biooxidation step. Biooxidation of the concentrate prior to cyanidation improves the recovery of precious metals, especially silver, and significantly reduces cyanide consumption from 18.7 kg/t to 3-5 kg/t of concentrate. INTRODUCTION Biooxidation of gold sulphide concentrates using acidophilic microorganisms has been successfully applied worldwide (van Aswegen et al., 2007; Gericke et al., 2009; Sovmen et al., 2007; Sovmen et al., 2009). At least 15 full-scale plants for tank biooxidation of sulphide concentrates are presently in operation, and the construction of new ones is planned (Bulaev et al, 2015)."

Jan 1, 2018

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

By M. Rudolph, D. H. Hoang, N. Kupka

"Froth flotation has been subjected to modelling since the 1930s and there is a large variety of approaches that intend to portray the entire process. Among these, three fundamental models could be considered exhaustive: the Pyke model [1], the Yoon model [2] and the Schwarz and Koh model [3]. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. Using a scheelite ore as a test case, a specific batch flotation test was repeated ten times and analyzed for chemical assays, mineralogical studies and froth properties. The detailed data are used to feed the three flotation models aforementioned in order to compare the outcomes of the three approaches, their capacity to reflect reality and to predict it. This article intends to pave the path towards reliable process models incorporating in depth mineralogy information, e.g. surface liberation, particle size and particle shape. KEYWORDS Froth flotation fundamental models, scheelite, automated mineralogy, critical assessment. INTRODUCTION In mineral processing, only three approaches aiming at describing froth flotation fundamentally could be considered exhaustive: Pyke’s collision and sliding approach [1], Yoon’s kinetic approach [2] and Schwarz and Koh’s approach [3]. The models will hereafter be referred to as Pyke model, Yoon model and Schwarz and Koh model. The first model makes use of the generalized Sutherland equation collision model, the Dobby-Finch attachment model and its own stability model, the second model considers an extended DLVO approach for the attachment and stability whereas the third model makes use of computational fluid dynamics. All three approaches rely on the widely accepted idea that flotation is a kinetic reaction dependent on a flotation rate constant kp, as expressed in Eq. [4]:"

Jan 1, 2018

By Alexander V. Epiforov, Stanislav V. Balikov

This paper describes of processing tests of 8 flotation concentrates containing precious and base metals by pressure oxidation (POX) method. Concentrates 1 and 2 were gold-copper concentrates. Zinc and silver were by-products in these concentrates. These concentrates were processed by POX with following cyanidation of POX solid residues, copper solvent extraction and zinc carbonate precipitation. The recoveries of gold, copper, silver and zinc from these concentrate were 98, 99, 30 and 99%, respectively. Concentrates 3 and 4 were lead-zinc concentrates. Silver was by-product in concentrate 3. Gold, silver and copper were by-products in concentrate 4. Concentrate 3 was processed by POX with following reduction smelting of POX cakes for primary lead recovery and zinc carbonate precipitation from POX solution. The recoveries of lead and silver into ingot were 96 and 98%, respectively. The recovery of zinc was 99%. Concentrate 4 was processed by POX with following zinc carbonate precipitation and reduction smelting of POX cakes. Copper was precipitated from the POX solution using sodium sulphide prior zinc precipitation. The recovery of zinc into carbonate concentrate was 99%. The recoveries of lead, gold and silver into lead bullion were 95, 99 and 98% respectively. The recovery of copper into sulphide concentrate was 99%. Concentrate 5 was gold-pyrite concentrate, and concentrates 6-8 were double refractory gold-arsenopyrite concentrates. Silver was by-product in these concentrates. These concentrates processed by POX and CIL. The recovery of gold from concentrate 5 was 98%, and from concentrates 6-8 was 85-90. Low gold recovery from concentrates 6-8 was associated with preg-robbing factor. The recovery of silver from gold-sulphide concentrates did not exceed 10-20%. The low silver recovery was associated with argentojarosite formation that is resistant to cyanidation. The flowsheets for complex processing of precious and base metals sulphide flotation concentrates based on this test work results were proposed.

Jan 1, 2018

By M. E. Taranenko, V. A. Krivonosov, S. A. Nemykin

"In concentrating production energy-consuming power installations are wide used, the most powerful of them are the wet autogenous grinding mill operating in closed circuit with a spiral classifier. The analysis of the current state of the automation of the grinding process shows that the reserves for maximizing productivity and minimizing electricity consumption have not yet been exhausted on the existing process equipment. Usage of the achievements of the modern management theory reveals an opportunity for further optimizing of the grinding process. The purpose of the research is to develop an automated control system of complex ""the mill-classifier"" to conduct the grinding process in the most operating efficiency, ensuring the maximization of productivity and minimization of specific electricity consumption. The main idea of this work is to study the specific features of the ore grinding process and creation on this basis of automated control system complex ""mill-classifier"" which allows to find and to maintain the optimal mode of grinding based on identification of the current object parameters, observance and regulating of the object state coordinates. Research methods. We used the methods of system analysis, mathematical statistics, modern automated control theory, theory of systems identification, optimal control, modelling of dynamic processes. Developed scientific provisions: - identification algorithm of the loading sub-system management object of complex ""mill - classifier"" allowing to obtain the unbiased estimators of its parameters according to the data of normal object exploitation; - observing device, which differs from the classic version of the observer Luenberger with possibility of estimating not only the state coordinates of the control object, but also the low-frequency perturbation component; - automated system stabilizing the active power of the grinding mode on the basis of a states controller with Luenberger observer; - structure of the software and hardware that implements the developed models, algorithms, methods of control, management and optimization in the framework of the automation of grinding."

Jan 1, 2018

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018