Search Documents

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By Vincent C. Smith, Agit Singh, Daniel de V. van der Spuy, Bernard Muller

"Process control in the minerals industry is made difficult by factors such as the multivariable nature of the processes, noise, many disturbances, the changing nature of the processes, nonlinearities, process constraints, slow responses and large deadtimes. A good example of such a process is a milling circuit, where all these problems are experienced. Since model predictive control (MPC) effectively handles most of these difficulties, Mintek decided to develop, customise and test an MPC controller for milling control.Conventional MPC uses a dynamic model of the plant to calculate the future (predicted) plant outputs based on the movements of the manipulated variables in the past. The future moves of the manipulated variables can then be calculated using an optimisation algorithm that will minimise the difference between the setpoints and the predicted outputs. The least squares optimisation method is the quickest, but it does not cater for process constraints. Constraints can, however, be handled explicitly by using a quadratic programming optimisation method. This method ensures that the variables stay within the constraints at all times, but the calculation procedure is much more computationally intensive.• modifying MPC for the Minerals Processing IndustryIt was found that in order to obtain good, robust control using MPC in the minerals processing industry, the conventional MPC algorithm had to be adapted. The MPC controller was first tested on an extensive milling simulator, which was specifically developed for that purpose. Problem areas were identified and the MPC controller was specially adapted to accommodate for these difficulties. Some of the adaptations to the conventional MPC algorithm and special features added were as follows:Since milling plants contain many integrating processes (e.g. sumps), and integrating errors can cause offsets and poor control, it was essential that integrators be handled explicitly. This problem was solved by adapting the algorithm and also using an integrating error portion to compensate for integrating errors.Constraints on the inputs and outputs adversely affected the control. The controller using simple least squares optimisation was tuned with the constraints in place, while the maximum expected setpoint changes were made. This ensured that the process would be able to handle most setpoint changes up to these expected values without violating the constraints. A later improvement on this method was the incorporation of a quadratic programming algorithm to perform the optimisation. This method handles limits explicitly and was shown to perform better than the least squares methods (at the expense of a much higher computational cost)"

Jan 1, 2003

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

"INTRODUCTIONThe grinding rate prediction scheme makes use of the energy spectra output from the DEM simulations and the statistical quantification of material strength, which can be done using the drop-weight tester or some other similar equipment. The prediction scheme is evaluated using milling experiments performed under well-defined conditions.MATERIAL STRENGTH QUANTIFICATIONUsing the drop weight test machine, particles of a wide size range were broken singly using different energy inputs. A characteristic equation key to milling rate prediction that relates the probability of fracture with energy input and number of impact attempts was obtained and is stated as follows:"

Jan 1, 2003

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By E. A. Bekchurina, Yu. P. Morozov

"This paper presents the results of a study of the concentration of flotation froths in tapered chutes. The tests were conducted on lab and full-scale plants, and the results obtained were mathematically processed. The kinetics of monophase recovery from a stationary flotation froth, hydrodynamics of froth flows traveling in a tapered chute were investigated. The effect was studied of the mass fraction of the valuable component in the chute feed, yield of the chute’s overflow, and chute design on the concentration performance. Processing of the collected data revealed the general laws of the process and allowed to develop a technique for modeling concentration of the flotation froths of sulphide copper ore in a tapered chute to predict the performance without testing. It was found that concentration in tapered chutes allows to obtain products that are comparable in quality with froths after one or several cleaner flotation stages.INTRODUCTIONThe present production expansion rates require continuous improvement in the grade of flotation concentrates, while the grade of the mineral feed is constantly deteriorating. This leads to a significant complication of flotation flowcharts. Flowcharts become multi-staged with multiple cleaner flotations, negatively affecting the production costs.In recent years, researchers are paying close attention to the processes occurring in the froth layer in the flotation cells. Improving the concentrate grade is facilitated by secondary concentration of minerals in the froth layer, which consists in fixing the hydrophobic particles released as a result of the coalescence of the bubbles of the upper layer when moving downward at the liquid-gas interface of the froth layer. In this case, the released hydrophilic particles, trapped in the froth layer as a result of mechanical removal, migrate from the froth together with the liquid phase."

Jan 1, 2018

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By M. Ghiani, P. Massacci, A. Manni, R. Peretti, Center for Mining and Mineralurgical Studies, S. Serranti

"The research study has been devoted to point out the better way to process a colemanite concentrate characterised by a high content of two kind of As sulphides (realgar and orpiment) finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to determine all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.There is a not neglectable part of realgar highly disseminated into the colemanite crystals.The orpiment recurs in small acicular crystals of 20÷30 µm in length and 5 µm in width, very difficult to liberate from the colemanite mineral particles.The colemanite concentrate, in fact, has been addressed to a chemical plant which products were boric acid and gypsum, the contaminated by As. It was unacceptable for further applications and very dangerous if rejected in the environment.Grinding tests under dry and wet conditions have been carried out in order to evaluate the liberation modality of the As sulphide minerals from the colemanite.Some difficulties have been overtaken in order to obtain a selective liberation of the As sulphides from the colemanite even if a certain decreasing in As grade in the higher size classes has been registered.All the comminution products have been analysed by SEM monitoring the liberation degree of the mineralogical constituents.Flotation tests have been carried out after different comminution flow sheet adopting different modulating conditions in order to evaluate the influence of the following parameters:• collector concentration versus contaminants concentration (As minerals) in the froths;• kind and quantity of the frothing agent to maximise the mineral recovery in the froths;• kind and quantity of the modulating agents to maximise the selectivity of the process;• conditioning modalities in order to obtain a suitable dispersion of fines and to avoid segregation of Asbearingparticles together with colemanite ones;• solid/liquid ratio of the pulp to minimise the water flow into the plant."

Jan 1, 2003

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By K. A. Natarajan

Involvement of various indigenous microorganisms in extracellular and intracellular iron oxide formation is a convincing index for iron ore biogenesis. Biomineralization of various iron oxides such as hematite, magnetite, goethite and limonite with the participation of aerobic and anaerobic microorganisms is well established. Various aerobic and anaerobic bacteria such as Gallionella, Leptothrix, Acidithiobacillus, Thermoplasmales, Pseudomonas, Bacillus spp and Shewanella putrefaciens, which are implicated in the formation of higher and lower oxides of iron have been isolated from different iron ore deposits. Diversity of microbial life in iron ore deposits can be put to beneficial use such as selective removal of undesirable constituents such as silica, alumina, clays, phosphorous and calcite and also to bring about environmental detoxification. Role of microorganisms such as Paenibacillus polymyxa, Bacillus subtilis, Yeasts and a sulfate reducing anaerobe in the biobeneficiation of hematite is illustrated. Surface chemical changes brought about by bacteria - iron ore mineral interactions are discussed with respect to hydrophobcity, adsorption isotherms, zeta potential data and bioreagents generation. Bacterial adaptation to minerals such as hematite, quartz, alumina, calcite, apatite and clays results in secretion of mineral ? specific biosurfactants such as proteins and polysaccharides. Such bioreagents can be used as selective collectors, dispersants and flocculants in iron ore beneficiation. Research results are highlighted to demonstrate silica, alumina, phosphate, calcite and clay removal from hematite. Environmental friendliness of such biobeneficiation processes is demonstrated with respect to biodegradation of toxic amine collectors, utility of ?in situ? organisms in enhancing settlement of fines in tailing dams and water harvesting. Keywords: bio-mineralization, bio-beneficiation, bio-remediation, Gallionella, Leptothrix

Sep 1, 2012

By Hermann Wotruba, Günther Petzold, Fabian Riedel

"Increased mechanisation in underground stoping operations results in higher waste percentages in the run of mine. A new method of reducing waste is optical sorting. Optical sorters have low maintenance costs and can be installed underground. Rejected waste can be backfilled directly without having to be hoisted, therefore increasing the shaft capacity for a more valuable product.Pre-Concentration by Optical SortingA series of tests with an optical sorter at the laboratories of the Mineral Processing Department of the RWTH Aachen have shown that it is technically possible to sort almost any kind of ROM which has even slight differences in colour (Platinum Reef, Gold Reef, Kimberlites, Industrial Minerals, Aggregates, Coal, etc.).By employing optical sorters prior to conventional sorting plants, it is possible to reduce the amount of waste to be processed. Figure one shows test results of ore which is quite similar in colour to the waste (grey). With increasing waste in the feed, the recovery decreases according to the graph. In figure two, the colour ratio parameter of the sorter was changed with a similar waste percentage in the feed. With increasing loss of ore, a cleaner product can be achieved. Before designing a sorting plant, throughput tests are carried out. Throughputs vary depending on the size range. Sorters have a limit of about 250mm top size. In this upper size range, throughputs of 150t/h can be achieved."

Jan 1, 2003

By C. A. C. Sequeira, G. N. Anastassakis

Electrochemical processes occur on nano-, micro- and macro- scale in numerous applications such as fuel cells, batteries, hydrogen production, mineral extraction, water treatment, electrotherapy, sensors and many others. In most of these applications, gases evolve either at one or both electrodes due to electrolysis. These gases form bubbles play a crucial role in electrochemical systems. For example, in electrowinning (EW) that is used to extract and refine metals such as Cu, Zn, Ni, Mn, and Cd from their solutions, in most cases the solution is acidic and oxidation of water molecules at the anode is the common counter reaction, which results in the liberation of oxygen bubbles. This generally requires a high overpotential and accounts for a considerable percentage of the energy consumed in metal EW electrolytic cells, apart from producing acid mist that is very corrosive for other cell equipment and building structures. The behaviour of bubbles in electrochemical systems is still a complex challenging topic which requires a better understanding of gas bubbles hydrodynamics and their interactions with electrode surface and bulk liquid, as well as between the bubbles themselves. The objective of the current paper is to briefly review the fundamental hydrodynamics of both gas bubbles on the electrode surface and gas bubbles interaction with the liquid bulk solution. The current work also investigates the impact of gas bubbling and some operating parameters in copper EW, such as current density (100-500 A/m2), temperature (25-75ºC), acidity (50-300 g/L) and a typical chemical mist suppressant (<50 ppm). The results clearly show that both suppressant and temperature reduced the overall surface tension of the solution. Also, chloride concentration and applied current improved electrolyte flow and copper quality at higher current densities. The current paper contributes to the development of mineral processing (specifically to copper hydrometallurgy), as it deals with fundamental hydrodynamics and interactions of gas bubbles that formed during copper EW and play a crucial role in copper electrochemical systems.

Jan 1, 2018

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By Hoon Lee

Laboratory tests were conducted to evaluate the breakage characteristics of pyrophyllite in a laboratory ball mill. In grinding tests, the breakage characteristics were analyzed using the mathematical kinetic models based on the two breakage functions; the specific rate of breakage and the primary breakage distribution. Two samples having similar chemical composition show identical values in specific rate of breakage. In comparison, there are different values of primary breakage distribution for each sample. The size distributions of the product with various grinding time are well described by the parameters from non-linear searching.

Sep 1, 2012

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012