Search Documents

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By C. Martinez, S. Helle, M. Pincheira

We studied the feasibility of automated mineralogy to discriminate between tennantite and enargite, the main sulfosalts found in the Rio Blanco deposit, Codelco-Chile, in order to predict the content of minor elements (As, Sb, Ag, Pb, Zn) that impact on the process and concentrate prices. The identification of these minerals is feasible using traditional microscopy, however not possible by automated mineralogy. This drawback prevents comparing the databases generated in the past by means of conventional microscopy with the information obtained at present by QEMSCAN. To differentiate enargite from tennantite the mineral composition of both sulfosalts was studied by electron microprobe. The presence of associated minor element contents of about 8% zinc in tennantites and not exceeding 0.07% in enargites were used to modify the SIP database of QEMSCAN to enable the quantification of these phases in samples of head, residue and concentrate coming from As-bearing domains of the deposits. Detection limits allowed to determine the mineral species in the head, concentrate and residues. The integration of methodologies such as automated mineralogy and microprobe can be used successfully to quantify the presence of some ore forming solid solution.

Jan 1, 2014

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Industrial minerals may contain the same elements in approximately the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques.• quantitative measurements by ebsdCommon automatic techniques describing the mineral contents and the occurrence of minerals in free and locked particles, are based on optical-, backscattered electron (BSE)- or X-ray-signals. There are various commercial software systems on feature analysis by backscattered and X-ray signals in combination with image analysis (e.g. Oxford Inca Feature, CSIRO QemScan).Especially in silicates, the occurrence of similar elements in the different minerals is common. Sometimes the various minerals not only contain the same elements, but also approximately the same amount of each element. In these cases BSE imaging and chemical analysis are not always sufficient for identification."

Jan 1, 2003

By C. Y. Sun

China is a country with abundant resources of tungsten, taking one of the world?s top-positions regarding both the total reserve and the amount of industrial production. China?s tungsten resources occur mostly in multi-metallic deposits rather than in single-metallic deposits. China?s multi-metallic tungsten ores have the characteristics of coexistence with other valuable components such as molybdenum, bismuth, copper, sulfur and fluorite. These ores are usually low in grade and difficult to process. The technological challenge in mineral processing lies in separation of multi-metallic components in these complex ores and a comprehensive utilization of natural resource. Several cases of industrial practice of processing China?s typical multi-metallic tungsten ores are presented.

Jan 1, 2014

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By W. X. Yin

Electrowinning of lead from aqueous solution of PbCl2 and electrowinning of manganese dioxide from aqueous solution of MnCl2 are two research focuses in hydrometallurgy. This paper investigated a new process of simultaneous electrowinning of lead and manganese dioxide in chloride medium. The simultaneous electrowinning process in chloride solution not only can prevent chloride from liberating at anodes but also obtain two electrolysis products and decrease electric energy consumption. Diaphragm cell is used in the simultaneous electrowinning process to form separate anode and cathode compartment. The effects of temperature, HCl concentration in anolyte, NaCl concentration in catholyte and electrolysis time on current efficiency and cell voltage are studied. The results indicate that current efficiency of anode and cathode for 5 hours is 99% and 96% respectively, average cell voltage is 1. 701V, the weight ratio of lead and manganese dioxide produced at electrodes is 2. 39:1 under the optimum conditions. As anode products, manganese dioxide is ??MnO2, content of which in the products is more than 92%.

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By Stoyan N. Groudev, Ioannis Paspaliaris, Plamen S. Georgiev, Irena I. Spasova, Kostas Komnitsas

"The uranium deposit Curilo located in Western Bulgaria for a long period of time was a site of intensive mining activities including both the open-pit and underground mining techniques as well as in situ leaching of uranium. The ore was rich in pyrite and, apart from uranium, contained some non-ferrous metals. The mining operations in the deposit were ended in 1990 but since that time the deposit is a permanent source of acid drainage waters. The generation of these waters is connected mainly with the oxidation of pyrite and other sulphide minerals by the indigenous acidophilic chemolithotrophic bacteria.Laboratory and pilot-scale studies revealed that an efficient clean-up of the above-mentioned waters was achieved by means of passive systems of the wetland type. In 2001 a wetland was constructed in the deposit to treat a portion of the acid drainage waters which were discharged to a small ravine. This ravine reaches into the Teina, a small river that is a tributary of the upper reaches of the Iskar river.The wetland was constructed in the ravine and its bottom was located on intrusive rocks with a very low permeability. The rocks were covered by a 30 – 50 cm layer consisting of a mixture of soil, plant compost and crushed limestone. The wetland was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Carex and Poa as well as different algae were also well present.The acid drainage waters treated by the wetland had a pH in the range of about 2.5 – 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The watercourse through the wetland covered a distance of about 0.2 – 1.0 l/s."

Jan 1, 2003

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By S. Jagdish

India ranks fourth in the world of iron ore production and exported 55% of the total iron ore production of 180.9 million tons in 2006-07. As per United Nations Framework Classification (UNFC), the total iron ore reserves in India is 25249 mt. This consists of about 14630 mt of Hematite ore and 10619 mt of Magnetite ore. While the deposits of magnetite iron ore are limited to the states of Karnataka, Andhra Pradesh and Tamil Nadu, hematite ore is available in abundance in Jharkhand, Orissa, Chhattisgarh, Karnataka and Goa. National Steel Policy, declared by government of India in 2005 envisages 110 million tons of steel production by 2020. This is likely to be revised upwards. Massive exploration work in iron ore is needed to convert the available resources of iron ore into reserve category. Steel Authority of India Limited (SAIL) produced more than 24.5 million tons of iron ore during 2006-07 and plans to produce 42.0 million tons per year by the year 2010-11 to meet the requirement for a hot metal production of 26.2 million tons. While processing iron ore, the challenge faced would be the reduction of the gangue materials ? alumina and silica. It is proposed to bring down alumina and silica in the iron ore to less than 2% each from the current level of 2.5%~3.5% each. Appropriate beneficiation schemes are being developed depending upon the mineralogical characteristics of iron ores at different mines in the country. The state-of-art beneficiation technologies like Hydro-cyclone, jigging, magnetic separation etc. will be incorporated. SAIL?s corporate plan envisages blast furnace burden of 15% iron ore lumps, 15% pellets and 70% sinter by 2010. This strategy opens up the opportunity of utilization of micro fines generated in the mining and beneficiation processes for pellet making. This also directs towards all together new technological approach to the beneficiation process. SAIL is planning to set-up three pelletisation plants of 2~3 mtpa capacity. Environmental issues like reduction in slime loss and utilization of dumped low-grade iron ore are very important. R&D Centre for Iron and Steel, SAIL has carried out extensive laboratory investigations in the above area. This will help in reducing the loss of valuable iron through slimes and also increase the iron ore resource base. Laboratory investigations indicate that low grade dumped ore fines with Fe: 55.5% can be upgraded to a product with Fe: 66.2% with about 48% recovery.

Jan 1, 2014