Search Documents

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By X. Cui

Hydrocyclone is widely used in closed-circuit grinding process. However, in the first classification operation of coarse particles with high pulp density, the shortcomings of traditional cyclone are that the grinding cycle load is much high, the apex of cyclone is easily to be blocked and classification efficiency is less. Specifically, the problems of traditional cyclone used in grinding process are as follows: (1) Mill utilization factor is low and its handling capacity is small. (2) Coarse particles mixing in cyclone overflow affects the following separation process and fine particles mixing in underflow causes over-grinding, which affects the total recovery rate of valuable minerals. (3) High grinding cycle load leads to large amount of high-density slurry pumping, which causes high energy consumption and severe wear of cyclones, pipelines and pumps. The applications of new type pre-classification hydrocyclone with centrifugal volute in the first classification process of Iron Mine Mill are introduced in the paper. Pulp particles fed in the centrifugal volute were arranged in advance, so that coarse particles can be far away from the overflow pipe, which can reduce the short circuit current to avoid coarse particles entering overflow and improve classification efficiency and accuracy of cyclone. The strong points of the new cyclone in the coarse classification operation are as follows: (1) finer overflow and less fine particles mixing in underflow improves classification efficiency more than 10%; (2) lower ball mill load cycle improves ball capacity more than 10%;(3) grinding energy consumption reduces by more than 20% and cyclone feed pump reduces energy consumption by more than 12%. In short, new type pre-classification cyclone with centrifugal volute solves the problems of fine particles mixing in underflow, high grinding cycle load and less classification efficiency in the coarse classification operation. Therefore, it has broad application prospects in ferrous metal and non-ferrous metal ore dressing plant.

Sep 1, 2012

By K. V. Fedotov, G. I. Sarapulova

The study is devoted to the earth's surface protection and is aimed at improving the ecological safety of the territories in the mining industry. Identification of the diagnostic signs and quantitative criteria for the disturbance of soil geochemical properties and water chemistry represent an important scientific task in anthropogenically disturbed landscapes in the context of comprehensive exploitation of mineral resources. The study is aimed at geological and ecological analysis of the migration peculiarities of the man-caused chemicals and elements in soils and soil-surface water environment. We received new results. These results assist in estimating the peculiar features of distribution of heavy metals total and mobile forms (Cu, Ni, Zn, Pb), depending on the physical and chemical parameters of the disturbed soils. We obtained the empirical relationships describing heavy metals localization and accumulation processes depending on buffer properties of soils (pH, N, Corg), salinization factor and contamination with oil products. Anthropogenic geochemical barriers spontaneously formed in the area of industrial facilities were revealed in the territories of industrial facilities. These barriers prevent the further distribution of elements and pollutants in the landscapes. This makes it possible to create their artificial analogues in order to limit further migration of pollutants and to immobilize valuable components. Analysis of diagnostic features of soils geoecological state and factors influencing the distribution of heavy metals in the soil-surface water geosystem allows the identification of the geochemical barrier type with the aim of elements immobilization in a limited area of the territory. We applied modern physical and chemical methods of analysis, a package of statistics programs in Excel and modeling techniques. The proposed approach is innovative and therefore can be attractive. The accumulation of useful components losses in mineral resources exploitation is a promising reserve for their recovery from the soil with specifically arranged properties. The methodology of this research is also promising for the prediction of the environmental emergencies of the anthropogenic nature. This is consistent with the requirements of state control of environmental safety in the course of comprehensive exploitation of mineral resources.

Jan 1, 2018

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By R. Prakash

Column flotation has now gained wide application in the recovery of various minerals. The performance of the flotation device depends on the mixing characteristics of the phases inside the devices. In this work, quality of mixing in a flotation column has been analyzed by using information entropy theory. Empirical models have been developed for flotation column with the parameters which affect the quality of mixing. The efficiency of the particle separation in the flotation column has been enunciated based on the quality of mixing. The present analysis on the quality of mixing in flotation column may give insight into a further understanding and modeling of flotation devices in industrial applications.

Sep 1, 2012

By Tom Liu

This paper is a fundamental study of bubble-particle collision efficiency in turbulent flows. A CFD-based microscale scheme for the prediction of turbulent bubble-particle collision efficiency in a 3D isotropic turbulent flow is developed, and in this way, turbulence effects on particle-bubble collision efficiency are taken into account for the first time. By comparing the computed results with experimental data from the literature, the CFD simulation is shown to correctly predict the bubble-particle collision efficiency in a quiescent environment. The CFD method was then applied to the investigation of bubble-particle collision efficiency in a turbulent flow, and the simulation results are shown to be qualitatively consistent with the real observations. The predicted collision efficiency can be used in a multiscale modelling scheme, which would account for all control variables in a flotation cell, such as impeller structure and tip speed, air nozzle structure and air flow rate This study indicates how microscale simulations of bubble and particle behaviours, coupled to macroscale CFD simulations of flotation cells, can provide a powerful tool predicting the flotation rate in a real flotation cell.

Jan 1, 2014

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

By E. P. Olberg, A. Yu. Chikin, S. V. Petrov, M. P. Belykh, N. L. Belkova

"Bacteria that grow in autochtonous communities of gold heap leaching (HL) wastes are adapted to high concentrations of contaminants and environmental conditions. An example of a mine in the Sakha (Yakutia) Republic showed that the bacterial factor had a significant influence on cyanide breakdown and copper and nickel removal in the conditions of HL ore pile zoning compared to chemical oxidation. The diversity of bacterial communities growing in natural and simulated conditions of a HL ore pile was determined for the purpose of the study. The identified bacterial communities included genus Achromobacter and Serratia, which were found to be adapted to a wide range of temperature and can be considered as potential microorganisms for detoxification of gold HL wastes. INTRODUCTION Technologies and systems of passive treatment are of a special interest in relation to solving environmental problems of gold HL wastes detoxification, when neutralization time is not considered as a limitation (Alvarez et al. 2005). Passive treatment methods are based on reagentless spontaneous breakdown of cyanide caused by natural factors, including activity of autochthonous bacterial communities. Implementation of a reagentless biodetoxification technology for mature HL operations provides reduction of environmental impact on industrial site locations and substantial economic benefits compared to conventional chemical processes of neutralization that prevail in the Russian Federation territory. Passive treatment of cyanide-containing wastes was investigated by M. Botz, T. Mudder, S.V. Petrov, L. Simovic, A. Smith, C.A. Young etc. However, the bacterial factor (autochtonous bacterial communities) role in this process is practically unexplored. Thus, the aims of the study included the investigation of a bacterial factor influence on passive treatment of gold HL wastes and the identification of functional groups of bacteria involved in passive treatment."

Jan 1, 2018

By Ranjeet K. Singh

Kelsey Centrifugal Jig was found to be promising for the beneficiation of fine coal particles. The present study was aimed at in-depth understanding of the separation features of Kelsey Jig through detailed experimentation. Beneficiation of fine coal of size 150 x 300 µm was studied in a laboratory Kelsey Jig. The thickness of the ragging bed is found to be an extremely crucial parameter apart from the other process parameters such as rotational speed and pulsation frequency. A constant pulp density (25% solids) of the feed slurry was maintained in the study. The feed rate was also kept constant at 50 kg/hr dry solids. Silica sand of size -1.68+0.85 mm was used as ragging material to avoid the pegging of internal screen having an opening of 425 µm. The rotational speed was found to have significant effect on the depth of the ragging bed and its porosity, which influenced the separation performance considerably. Pulsation was identified as the key factor in stratifying the coal bed and defining the misplacement as well as ragging bed porosity, which influenced the mass yield and quality of the products. Beneficiation studies were carried out with rotational speed varying between 900-1000 rpm while pulsation frequency was kept within 850-925 rpm. In a single pass through the Kelsey Jig 7-8% (absolute) reduction in the ash content of the feed material was observed at more than 55% mass yield. High rotational speed, moderate pulsation, and low ragging bed depth favored good cleaning. A high bed depth was found to facilitate rejection of high ash materials. It was established that Kelsey Jig is effective in fine coal cleaning though a controlled operation is required in order to achieve superior performance. Keywords: enhanced gravity separator, g-force, separation performance, ragging material, coal beneficiation

Sep 1, 2012

By X. Y. Liu

A culture-independent approach based on 16S rRNA gene clone library was used to analyze the bacterial community change both associated to the solids and in the liquid phase during pyrite bioleaching process. Phylogenetic analyses of 16S rRNA fragments revealed that the retrieved se-quences mainly related to genus Leptospirillum, genus Sulfobacillus and genus Acidithiobacillus. During the bioleaching process, genus Leptospirillum trends to grow associated to the solids while major of genus Sulfobacillus were in the liquid fase, only accounting little portion in the solids. Genus Acidithiobacillus can grow both on the solids and in the liquid phase, but accounting high portion on the solids.

Jan 1, 2014

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012