Search Documents

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By A. Shandilya

ACC ECOSAND is finely powdered crystalline silica, which can replace natural sand usage in concrete and plasters. ACC ECOSAND ensures a comparatively denser concrete than those made only with natural sand and / or quarry fines / Manufactured Sand (Artificial Sand). Moreover, there is a significant gain in compressive strength (10-15 %) & durability in concretes (Reduced chloride conductivity leads to increased durability). ECOSAND is a by-product of froth flotation of limestone. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full-fledged mineral beneficiation process is adopted to enhance the usage of flotation reject in concrete and plasters. Optimum level for usage of ECO-SAND is 50%. With 50% usage of natural sand+50% ECO-SAND in concrete mix, 1 day, 3 day, 7 day & 28 day compressive strength is increased by 30.1 %, 22.6 %, 15.1 % & 11.0 % respectively and with moderate chloride permeability as compare to 100% Natural Sand. Keywords: froth flotation process, beneficiation studies, Denver cell, ECOSAND, siliceous material, durability & compressive strength, RCPT

Sep 1, 2012

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By Ela Mielczarski, Jerzy A. Mielczarski

"The adsorption of xanthate takes place at a different potential on each major sulfide mineral, hence, as it was demonstrated in the past, each mineral component can be selectively separated from ore under well controlled potential conditions. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from complex surface reactions controlled by solution chemistry, and there is a galvanic interaction between different mineral particles present in the flotation pulp.In this study the formation of amyl xanthate hydrophobic products on pyrite, galena and chalcopyrite has been spectroscopically investigated in the presence of combinations of these minerals. The type of the adsorbed species and their amount were determined directly on mineral surfaces by infrared external reflection technique. Galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on both minerals. The detected changes are dramatic, from no adsorption to a coverage formation of a few monolayers. The results obtained indicate clearly that the observations and conclusions about the collector adsorption, hence also the surface hydrophobization, made for a single mineral system does not describe the real situation in a multi-component mineral system such as flotation pulp."

Jan 1, 2003

By W. M. Zeng

A mixed culture of moderately thermophilic microorganisms was enriched from Acid Mine Drainage (AMD) samples collected from several chalcopyrite mines in China,which can leach copper from chalcopyrite effectively. Its tolerance to chalcopyrite was brought up to 80 g/L after being adapted to gradually increased concentrations of chalcopyrite. The effects of several leaching variables on copper recovery in Stirred Tank Reactor had been investigated. The ore contained chalcopyrite (62.2%) and galena (25.6%) as the main sulfide minerals. The results of the tests show that it is possible, operating at 8% of pulp density to attain copper extraction of 75% in 44 days. The leaching rate of chalcopyrite tends to increase with the dissolution of total iron. Microscopic counts of microorganisms in the solution tend to be higher at low pH range. Furthermore, the analyses of leached residues indicate that the passivation of this chalcopyrite is mainly due to the formation of a mass of jarosite and anglesite (about 48.3% and 21.7% in residue respectively), other than elemental sulphur layer. The bacterial community composition was analyzed by using amplified ribosomal DNA restriction analysis (ARDRA). Two moderately thermophilic bacteria species were identified as Leptospi-rillum ferriphilum and Acidithiobacillus caldus, with different proportion in the bio-pulp, 67% and 33%, respectively.

Jan 1, 2014

By Massimiliano Zanin, William Skinner, Keith Quast

With the scarcity of fresh potable water on mining sites, particularly those in arid and remote regions, the use of sea water is being contemplated and actually used at a number of mineral concentrators worldwide. The use of sea water, with its associated high dissolved solids content and ionic strength will affect all aspects of processing (e.g. frothing and froth stability, buffering capacity for pH control, solubility of minerals and corrosion of media and equipment). Selective depression of pyrite is more difficult in sea water due to the increased lime addition to achieve a high pH. This results in a reduction in molybdenite recovery. The use of grinding media with various chromium contents and its effect on subsequent Cu and Mo flotation has been investigated in the current study, with both grinding and flotation testing conducted in artificial sea water. Pulp chemistry (pH, Eh and DO) have been logged during grinding, and flotation testing was conducted on subsequent slurries. The flotation results show that the system is remarkably robust and able to cope with wide ranges of pulp chemistry parameters. The effects of artificial sea water on the surfaces of minerals during grinding have been examined using X-Ray Photoelectron Spectroscopy

Jan 1, 2014

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

By M. Brozek

The particle settling velocity is the argument of separation in such processes as classification and enrichment in jigs. It characterizes material forwarded to the separation process and belongs to the so-called complex arguments because it is the function of particle density and size. i.e. the function of two simple arguments. The affiliation to a given subset is determined by the values of two mag-nitudes and the distribution of such argument in a sample is the function of distributions of particle density and size. The paper will present a method of determining the distribution of settling velocity in the sample of spherical particles for the turbulent particle motion in which the settling velocity is expressed by the Newton formula. Because it depends on density and size of particle which are random variable of certain distributions, the settling velocity is a random variable. Applying theorems of probability, concerning distributions of function of random variables, the authors will present general formula of probability density function of settling velocity for the turbulent motion and particularly calculate probability density function for Weibull?s forms of frequency functions of particle size and density. Distribution of settling velocity will calculate numerically and perform in graphical form.

Jan 1, 2014

By Nicolás Caussade

"The IMPC 2014 slogan "Optimizing Water and Energy Usage for Sustainable Mining" refers to the ever decreasing availability of fresh water and energy, which has turned out to be a crucial aspect in assuring the competitiveness of the mining sector in Chile and the Andes region in general. The concern for sustainability and the supply of water and energy is nowadays part of the top priorities of mining countries and communities. This is also the case for Antofagasta Minerals. Several years ago its mining group implemented an energy policy based on intelligent, strategic and sustainable management, in order to successfully face the challenges imposed by the market. It is called an intelligent policy because it intends to provide energy through a diversified range of sources, which includes the development of in-house alternatives. It is also a policy focused on efficient energy consumption and one that is strategic. Because it is in line with the characteristics of the mining activity, it is developed for the long term. Finally, what makes the policy sustainable is that it gives priority to energy usage from renewable resources and as such, the required capacities have been developed to generate innovative solutions that respond to the restrictions that characterize the industry today."

Jan 1, 2014

By P. Somasundaran

While sustainability itself needs to be redefined in a selfless way, methods of measuring and optimizing it also need to be reformulated. Gone are the days when we had the luxury of abundant resources and the freedom to extract values in self-centered ways. In the past, focus has been mostly on reagent performance, processing operations, and upgrading of tools to maximize rather than optimize value extraction from the earth's crust. Today we as extractors face a new set of challenges that include value separation from low quality resources including wastes, but within the energy, environment, and societal constraints. Development of such technology depends on understanding the role of entities and concepts such as bio-molecular interactions at surfaces, forces involved in inter-granular versus intra-granular fracture in new fragmentation methods, robotic in-situ or extraterrestrial mining, exploiting new membrane and nano technology, use of new sensors and actuators for detection and separation and computation capabilities for faster and economical processing. Equally importantly, we need to communicate with everyone what we foresee and anticipate when we extrapolate the type-performance-cost relationship of ores to the era ahead of us and establish viable schemes for ecological survival. Keywords: sustainable mineral extraction

Sep 1, 2012

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012

By N. Schreithofer

Varying flow regimes, particle populations and consequently different types of bubble-particle interactions characterize the different zones of a flotation cell. The understanding of the role of the different zones of turbulent intensity on the particle-bubble interactions is of primary importance to optimization and scale-up of flotation processes and machinery. In order to study particle-bubble interaction in turbulent flow a completely new approach was taken. A laboratory scale stationary turbulence device was developed and built. The set-up allows the observation of particle-bubble interactions in various turbulence intensities, particle and bubble sizes and surfactant concentrations. The experimental set-up consists of a transparent, specially designed tank in which liquid flows between carefully designed and placed obstacles that create different turbulent flow fields. Bubble-particle aggregates are introduced into this turbulent zone. The behaviour of the aggregates, such as attachment /detachment of particles to/from air bubbles is recorded by a High Speed Imaging (HSI) system (5400 fps). The images are then analysed and the dependence of attachment/detachment process is described as a function of turbulent intensity in different conditions for different surfactant concentrations. This paper introduces this method to study particle-bubble interactions in turbulent flow and correlation to Computational Fluid Dynamics (CFD) simulation. CFD modelling is validated for two and three phase systems; liquid-gas with liquid and solid tracers respectively. The CFD simulations using the RANS k-S turbulence model showed good correlation to the experimental data and the experimental method is a promising tool for investigation of particle-bubble interaction in turbulent flow.

Jan 1, 2014

By Rasool Hejazi

The feed to Chadurmalu iron ore concentrator plant is a mixture of magnetite and haematite iron ore with a Fe/FeO ratio of about 8. The feed to plant, after grinding via wet SAG mill, is pre-separated by wet low intensity magnetic separator. Magnetic product is conducted to magnetite processing circuit for producing magnetite concentrate, and nonmagnetic product is directed to haematite processing circuit. Due to surface oxidization of magnetite particles and a decrease in magnetic attraction properties, significant amount of these particles are misled to tailing which results in decreasing the efficiency of haematite processing circuit. This problem can be remedied by using magnetic drum separator with more magnetic intensity and/or gradient. In this paper, the replacement of LIMS separators with wet medium intensity magnetic separators with a field intensity of 3800 gauss on drum surface (MIMS) have been suggested and considered as the most suitable solution to prevent the loss of magnetite particles. The results of carried out investigations with replacement of drum separators in industrial scale, showed that utilizing MIMS in magnetite processing circuit resulted in increasing final concentrate weight recovery on average by 2.59%, without any adverse effect on the concentrate quality; decreasing the magnetite content in the feed to high gradient magnetic separator (HGMS) by about 3.5%; decreasing the feed to floatation part by about 7% and consequently decreasing consumption of chemical reagents; increasing Fe/FeO ratio of the feed to plant. Keywords: iron ore, medium intensity magnetic separator, haematite, Chadurmalu

Sep 1, 2012

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

By A. Pankewitz

The well-established on-line particle size analyzer OPUS manufactured by Sympatec GmbH, has been successfully implemented in several mining and industrial minerals project. OPUS monitors the particle size distribution in 31 fractions as well as the solid concentration in opaque and highly concentrated ore and mineral slurries on-line in real time e.g. behind mills or cyclones applying 31 ultrasonic frequencies for highest resolution. Ultrasonic extinction overcomes all limitations known from optical and mechanical systems like contamination, blockage and wear. OPUS measures slurries in their original state without any dilution, hence no extensive sampling procedure or sample conditioning is required thus no dilution errors occur. Due to the OPUS design and suitable algorithms entrained air bubbles do not affect the quality of analysis at all. The sensor covers particle size distributions from 0,01 to 3.000,00 µm and solid concentrations up to 70 % by volume and can be easily adapted to a number of production lines simultaneously. Jiangxi Copper?s Dexing Mine is one of the biggest copper mines in Asia and among the first users for OPUS on-line particle size and concentration analysis in mining industry. OPUS is connected to 2 process lines. Jiangxi Copper has implemented OPUS for into their central control system for the grinding & classifying circuit of one SAG mill and one ball mill. Analysis data and process control as well as optimization based on OPUS particle size and concentration measurements will be discussed Keywords: particle size analysis, ultrasonic extinction, concentration analysis, grinding control

Sep 1, 2012

By Yuri Yemelianov, Stanislav Balikov, Alexander Epiforov, Andrey Boldyrev, Andrey Bogorodsky

"Test work was carried out using copper gold-bearing flotation concentrate with 6.85%Cu, 14.30%Fe, 20.70%S and 2.34%As. Gold and silver grade in the concentrate is 54.6 g/t and 92 g/t, respectively. Gold and copper are valuable components in the concentrate. Gold is partially associated with pyrite and fahlores. Copper in the concentrate can be found as tennantite (Cu12As4S13). The 71% of gold from the flotation concentrate is recoverable by cyanidation with simultaneous cyanide consumption in the amount of 96 kg/t. The major reason of refractoriness is that gold is fine encapsulated into sulfides and the presence of cyanicide-copper. The concentrate ground as much as 95% minus 10 µm was treated using low-temperature POX at the temperature of 100±5°C, L:S ratio of 5:1 and the process time of 1-5 hours. Residual sulfide sulfur in the cake is 2.28% which is 89% sulfide oxidation. The highest copper recovery to POX solution is 91%. It was found that gold recovery to cyanide solution is 85-94% during alkaline pre-treatment of POX cakes followed by cyanidation. In this case, cyanide and lime consumption is 75-90 kg/t and 120 kg/t, respectively. In order to recover precious metals from POX cakes leaching using sodium sulfite was carried out. Test work was conducted at varied reagent concentration, L:S ratio and leaching time. Gold and silver recovery achieved was 85-95% and 59-63%, respectively."

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014