Search Documents

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By O. A. Bascur

"In recent years, metal producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Internet of Things (IoT) is one of many transformational initiatives, which can fundamentally revolutionize how industrial complexes operate. Whatever the issue, the answer is in the abundant and growing quantity of real time data and events collected in the grinding and flotation circuits in a mineral processing plant. Based on earlier work, today a grade recovery model permits identifying the best operating conditions in real time. We will review the strategy for increasing the value of the abundance instrumentation in current plants. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut to reduce metal losses in the flotation circuits. The large amount of sensors in a flotation circuits permits to estimate the recovery and to find the optimal froth depth and aeration using an air holdup flotation model. The paper will describe the strategy of classifying data for on line generation of insights to using operational intelligence tools. We will discuss the implementation Recovery/Grind strategy with industrial examples in non-ferrous mineral processing and iron beneficiation.INTRODUCTIONThe declining supplies of high grade ores and increasing consumption of mineral and metal products have demanded higher operational efficiencies with minimum capital investments. The objective of copper flotation objectives are based on maximizing the dollars return on the concentrate produced. The economic efficiency is maximized by manipulating the circuit along the grade/recovery curve relationship. To achieve such objective improved stabilization of the grinding and flotation circuits are required (Oosthuizen, Craig, and Jamsa-Jounela, 2017)."

Jan 1, 2018

By James A. Finch

"Developed countries are in the midst of re-structuring education in minerals-related disciplines as raw materials, once vital to wealth generation, contribute progressively less to the economy. The changing circumstances mean institutions must justify mineral processing by new criteria. After considering what a mineral processor needs to know the ways to deliver are considered. Taking twenty graduates per year to illustrate, one institute could justify this number as a program in a department or school (of whatever grouping of disciplines). A strong research component would make the package additionally attractive. Divide among four institutions and mineral processing is best served in a research centre with delivery taking advantage of multi-centre and distance learning opportunities.INTRODUCTIONThis is one of five plenary lectures at the Congress. I may have preferred a technical subject, as that is what occupies most of my thinking hours, but it is reasonable as an academic that this topic should come to one of us. The fact the topic has not been high on my agenda may provide one advantage: that I can suggest directions free of pre-conceived notions, just as when reviewing the background to a technical article the temptation to select in support of one?s interpretations is resisted. The trick will be to add something new.One reading of the title seems to query whether mineral processing education has a future. (I will refrain at this juncture from defining mineral processing and assume for now we share an understanding of the term.) The proximity of natural and human resources led to the Industrial Revolution and the interaction continues to stimulate and sustain industrial and economic development in many parts of the world. The search for raw materials has historically played a key role in opening frontier areas, with undersea and outer space next. The reason is obvious: raw materials along with food and energy underpin society. Thus mining will remain part of human activity along with the need to pass on the knowledge and skills.What happens over time is resource relocation. Raw materials become exhausted in one area to be replaced by sources elsewhere; the demand for some materials lessens while growing for others. Educational institutions can find themselves with the wrong geography or with staff focussing on the wrong subjects. When this happens the restructuring produces much discussion. This is where we are in parts of the world. Japan, Western Europe and the United States are the prominent examples (Dowd, 1998; Flemings and Suresh, 2001; McDivitt, 2002). Mineral processing is becoming a series of courses in related disciplines: resource engineering, environment engineering or materials engineering. The start of the transition is evident in Canada and Australia, perhaps earlier than expected given the contribution of raw materials to their economies. A common backdrop in the developed countries is social pressure to reduce the impact of the ?untidy? aspects of life, and that includes mining. (This is not new: in classical times the mine face was the preserve of slaves and convicts.) These values are exportable, potentially affecting recruitment into mining schools everywhere."

Jan 1, 2003

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By Chris A. Fleming

"The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative.There is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and nontoxic metals and ions in the tailings.This paper briefly discusses the pros and cons of the different processes that are available for the treatment of gold plant tailings to regenerate and recovery cyanide for recycling, and presents a techno-economic argument for the incorporation of this technology into many gold plant flowsheets today."

Jan 1, 2003

By G. Semenchenko

Heterotrophic microorganisms Pseudomonas aureofaciens, microscopic fungi Fusarium sp. and their combinations with some chemical substances were used for gold leaching from refractory ore and flotation concentrateof Akbakaj deposit. All biological additives raised the speed of noble metals dissolution. The best results of gold extraction from ore were in the presence of bacteria or their associations with other solvents and from flotation concentrate in the presence of fungus - 30 % of additional amount of gold. The maximum extraction of gold speed value was during the first 8 hours of process. The electronic-microscopic researches of the ore samples showed almost complete decay of pyrite and arsenopyrite under bacteria influence whereas at chemical leaching most of these minerals stayed uncrushed. The presence of microscopic fungi in flotation concentrate during leaching provided full distraction of pyrite, but some crystals of antimony and arsenopyrite were undestroyed. During cyanide leaching of flotation concentrate there were accumulation of antimony and incomplete pyrite decomposition. Keywords: gold bioleaching, bacteria, fungi, complex solution

Sep 1, 2012

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By R. Hejazi, Saghaeian. M., H. Abedini

Continuous vacuum belt filters mainly carry out an important duty in the solid-liquid separation processes such as iron ore concentrate dewatering. However as the particles become finer, the resistance to filtration and dewatering would increase and as the result cake moisture content tends to increase. So in recent decades, using additives in order to improve the filtration performance has been considered by many researchers. In the present study, the effect of several surfactants on the filtration rate and cake moisture content of Chadormalu iron ore concentrate (80% =40 micron) was investigated using a laboratory scale vacuum filter. The results of several tests indicated that a non-ionic surfactant (Lauryl Alcohol Ethoxylated, LAE) has the best performance on reducing the moisture content of the cake and reducing the cake formation time. The optimum dose of LAE was found to be 300 g/ton which reduced the concentrate cake moisture content from 13.76 to 11.28% (wet weight base). Some industrial filtration tests were performed in Chadormalu iron ore concentrate plant to prove the effectiveness of this surfactant. The surfactant is mixed with water and added to the concentrate slurry before distributing on the vacuum belt filter. The industrial and experimental results were almost similar, so that adding about 300 g/ton of LAE would reduce the final cake moisture content from 12.87 to 10.76%.

Jan 1, 2014

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By B. Gorain, O. A. Bascur

"The advent of digital revolution has now enabled us with numerous tools that could be leveraged to transform our operational data into actionable insights. Key opportunities with digitization include better visualization, transparency, integrated planning and execution for value-chain optimization, that results in smarter production, intelligent response to changes in ore, process and equipment conditions, reduce energy and waste along with prevention of asset breakdown, safety and environmental issues. It is important to realize that these digital tools have limited value, from a metallurgical operational context, if we cannot bring-in the appropriate domain expertise along with getting the basics right. The focus within Barrick is to ensure that there is adequate depth of different disciplines built into our platforms along with breadth to integrate other disciplines such as geology and mining for an effective Mine-to-Mill integration. A gold recovery improvement strategy based on optimal Gaudin size distribution, leaching performance monitoring and guidance via feed grade maps is discussed. Simultaneous identification of process and equipment constraints enable finding the best overall conditions for Gold recovery. This paper discusses the methodology, findings, and challenges in the ongoing journey of implementing a Metallurgy Analytics platform that evolves from being retrospectively descriptive to anticipatively prescriptive.INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stakeholders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance."

Jan 1, 2018

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

By Carlos Gualdron, Elizabeth Gomez, Rafael Bolivar

The productivity index of the Coopracarcegua Ltda., a mid-size coal mining company of Norte de Santander, Colombia, was related absenteeism using accident, productivity and profit data four years. The analysis was based on type, severity and frequency of accidents, number of absentee days; price per metric ton, and other relevant parameters. The enterprise is formed by 5 different mines of thermic coal, each one with different exploitation technologies and different productivity. Each mine was analysed separately and the loss of profit due to absenteeism was calculate for each one. The study showed that the foregone earnings due to absenteeism in terms of the whole productivity of the enterprise was about of 6.6% of the total profit average the 4 years, with calculated values of 14.7%, 3.5%, 8.4% and 4% per year in the evaluated period. The study identified that the most important cause of absenteeism was "General Disease". The foregone earnings in 2009, the highest loss for the analysed period, was about US$ 0.937 million and during the whole evaluated period was US$ 2.46 million.

Jan 1, 2014

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. The starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions round the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions.

Jan 1, 2003

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018