Search Documents

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Kosuke Nishioka, Yasushi Kihara, Altansukh Batnasan

The aim of this study was to investigate the feasibility studies of seawater in flotation of a 1.5 mass % of copper containing copper sulfide ore. Effects of seawater, various frothers, and different distilled water/seawater ratio on flotation of copper sulfide ore were studied. Surface properties of native copper ore and sea water soaked were examined by using FT-IR spectrometry. Chemical contents of the copper sulfide ore and after flotation were identified using XRD studies. XRD pattern showed that the main constituents of the copper sulfide ore are chalcopyrite (CuFeS2), bornite (Cu5FeS4). Flotation experiments were carried out using mechanical agitation flotation equipment with a mineral separation type flotation cell. Froth flotation experiment was conducted using calcium hydroxide was used as a pH adjuster, using methyl isobutyl carbinol (MIBC), dow froth 250 (DF 250) as frothers and potassium amyl xanthate (PAX) as collector for the copper recovery from the copper sulfide ore containing chalcopyrite and bornite. The results showed that the copper recovery by flotation was dependent on the flotation medium and frother. The main results showed that the copper recovery by flotation was dependent on the process water and frother. The copper recovery reached 97 % and 87 % in the distilled water flotation and seawater flotation with MIBC, respectively. For seawater flotation with DF 250, the Cu recovery achieved near 95 % and grade of Cu in the froth product after 5 min flotation was reached 29.8 mass %.

Jan 1, 2014

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

"The work in the paper introduces a 2-dimensional finite element model for analyzing particular material processing in a roller press. Two basic roller geometries are considered: (a) smooth rolls (used for milling and compaction) and (b) rolls with cavities, commonly used for briquetting. A model is presented that is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables.MODEL, RESULTS AND CONCLUSIONSAn associated Gurson model was employed as a constitutive model for the material. The calibration of the model was based on experimental results from an instrumented compaction die. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Powder River Basin sub bituminous coal fines with moisture content 9% was used as a model material.Two finite element models have been set up, one for the briquetting roll and one for the “equivalent” flat roll. Approximately 3200 plain strain continuum elements with reduced integration (CPE4R) were used. Lagrangian-Eulerian (ALE) approach in conjunction with judiciously applied remeshing was employed with the commercially-available, dynamic explicit version of ABAQUS finite element code.Comparison of model predictions with experiment shows that there is an agreement in terms of the general trends of experimental values recorded on laboratory roller presses. Gurson model overpredicts stresses at low densities and, as a consequence, overpredicts roll force and roll torque."

Jan 1, 2003

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Georg Unland, Thomas Wegner

"Different types of impact crushers use the physical effect of impact to crush rocks. The rocks can vary from soft to hard and from ductile to brittle but they should never be abrasive. Since the principles of impact crushing of larger rocks are hardly investigated these crushers are still sized rather by empirical than by scientific approaches.In order to investigate the principles of comminution by impact of large rocks a test rotor was developed and rocks of different dimensions were tested. The integrated measuring devices of the rotor enable the recording of impact forces and of absorbed impact energy with high resolution during the contact time.Since impact crushers stress the rock particles with a defined velocity the main crushing properties are gained as a function of the applied velocity and the particle size of the rock: likelihood of breakage, contact time, maximum crushing force, mass specific crushing work, surface related crushing ratio and crushed fragment shape distribution."

Jan 1, 2003

By John Nell, Paul den Hoed

Carbochlorination tests were conducted with matched particle-size fractions of rutile, ilmenite and high-titania slag in a small bubbling fluidized-bed reactor. The effects of temperature, the type and proportion of solid reductant in the charge, and the fraction of Cl2 in the fluidizing gas were investigated. Tests confirm the need for solid carbon in the bed if chlorination is to run at high rates. With solid carbon in the bed, CO supplied with the fluidizing gas does not increase significantly the degree of chlorination after 75 minutes. Ilmenite is chlorinated more quickly than titania slag, which in turn is chlorinated more quickly than rutile. Rates of chlorination at 1100°C and 1000°C are much the same and significantly higher than at 900°C. Chlorination is associated with significant increases in particle porosity (even for rutile), which is brought about by the rapid initial chlorination of FeO and MnO (in ilmenite and slag) and (it is argued) by the chlorination of Ti2O3 which forms at high-energy surface sites. A reaction mechanism is presented; where possible, its validity is demonstrated by the support of empirical observations.

Jan 1, 2003

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By J. W. Ahn

Calcined calcium oxide from limestone is hydrated to manufacture calcium hydroxide, and then precipitated calcium carbonate is synthesized from calcium hydroxide. Precipitated calcium carbonate of various morphologies is obtained by controlled conditions of each step and characteristics of limestone, calcium oxide and calcium hydroxide. Especially characteristics of calcium hydroxide have the most influence on morphology of precipitated calcium carbonate character. In this study, therefore, it is investigated the specific surface area of calcium hydroxide and morphology of precipitated calcium carbonate according to hydration temperature. Calcium hydroxide hydrated at high initial temperature has larger particle size than that hydrated at low initial temperature. And formation yield of aragonite precipitated calcium carbonate has improved by using calcium hydroxide had larger particle size (hydrated at high initial temperature).

Jan 1, 2014

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014