Search Documents

By Bharat Garg

The coking coal or clean coal from raw material division, Tata Steel Ltd. is a prime source of energy for inhouse steel making. Coal reserves of semi soft coking coal at West Bokaro is beneficiated by dense media cyclone and froth flotation processes to produce clean coal. In dense media cyclone process two byproducts-middling and rejects are also produced along with clean coal. With the growing demand for clean coal, it becomes imperative to maximize the recovery of clean coal in beneficiation processes. This will help, not only in reduction in cost of production, but also in raw resource conservation, and proper utilization. In this context, a case study was conducted at West Bokaro to identify opportunities for clean coal recovery from by-products. This paper mainly discusses the process for recovery of clean coal from byproducts and study of further liberation of clean coal from byproducts for economic consideration.

Sep 1, 2012

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates."

Jan 1, 2003

Under the sponsorship of the U.S. Department of Energy, a project was completed in 2005, which studied the use of a special pneumatic capsule pipeline (PCP) system, driven by linear induction motor (LIM), for transporting minerals and/or mine wastes. In this study, the pipeline is a rectangular tube of 1m × 1m cross section. The capsules are similar to railroad cars running on small rails imbedded in the tube. A LIM is placed AT the entrance of the tube to transfer power electro-magnetically from the LIM to capsules. The capsules going through the LIM, propelled by the electromagnetic field generated by the LIM, move faster than the air and hence impart energy into the airflow. This in turn pushes the capsules in the tube forward. When the tube is long (say longer than 10 km), additional LIMs may be needed along the tube to serve as booster pumps. An advantage of using LIMs instead of blowers as used in ordinary PCPs is that capsules can pass through the LIMs unhindered. This enables the use of booster pumps for long tubes. It also enables PCP to achieve much higher cargo throughput than that of PCPs using blowers, thereby reducing unit cost ($ per ton-km). Advantages of using capsules with steel wheels running on steel rails in the tubes including: (1) contact friction is only about one-fifth of that using rubber tires, thereby conserving energy, (2) capsules can run at a much higher speed than those using rubber tires without overheating and damaging the tires, and (3) rails make capsule motion control simple; they restrict lateral movement of capsules, and make branching easy-by using standard rail crossing equipment. This advanced PCP system combines the advantages of LIM with the advantages of rails, resulting in a super-efficient tube system having throughputs an order of magnitude greater than that of conventional PCPs, and having an energy efficiency better than railroad transport. Analysis shows that the system is highly cost-effective when throughput is high-at least 5 million tons per year. The system is most suitable for long-distance transportation of minerals (including coal and flyash) and wastes (including both mine wastes and municipal solid waste).

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates.INTRODUCTIONThe process of leaching is widely used in hydrometallurgy to selectively recover a metal of interest from an ore or a concentrate. Leaching and by extension hydrometallurgy is well established in the recovery of copper (copper heap leach ? SX-EW), nickel (Moa Bay and Caron process), zinc (roast ? leach ? electrowin and zinc pressure leach), gold (cyanidation) and uranium (acid sulfate leach). Of course this success extends to many of the metals found in nature. Recently, the importance of hydrometallurgy appears to be increasing with hydrometallurgy viewed as an attractive alternative to both traditional mineral processing and conventional smelting/converting/refining. This increasing interest has led to intensive study and increasing application. Selected developments include:Copper ? the Mt. Gordon process and new concentrate processes such as INTEC, Activox, CESL, Dynatec, Total Pressure Oxidation, MIM Albion, BioCop, and the AAC/UBC Process.Nickel ? Voisey Bay process for hydrometallurgical treatment of Voisey Bay concentrate, HPAL processing of laterites at Murrin Murrin, Bulong and Cawse, atmospheric leaching of laterites, heap bioleaching of nickel sulfides by Titan Resources (Australia).Zinc ? establishment of zinc leach, solvent extraction and electrowinning technology for treatment of the Skorpion deposit in Namibia, new developments in atmospheric and pressure leaching, the Hydrozinc process.Gold ? development of a number of thiosulfate leaching processes for recovery of gold from refractory carbonaceous ores or concentrates."

Jan 1, 2003

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By X. Y. Zeng

Most Chinese titanium bearing minerals are the composition of magnetite vanadium and ilmenite. All of such mineral processing plants use low intensity magnetic separators to recover magnetite and vanadium goes with magnetite. In the past years most of the plant tails containing about 10% TiO2 were abandoned. Now many of these plants use SLon magnetic separators to recover ilmenite in the roughing stage, which can throw away most of the gangs and slimes with very low cost. The new development of applications of SLon magnetic separators in Chinese ilmenite processing industry is introduced in the paper.

Jan 1, 2014

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached to extract gold. The main aim is to decrease the arsenic content in processed materials and to break up the ore lattice, thus liberating the gold. Some regulations were established by authorities for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot plant testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum, arsenic is sublimated into elemental and sulfide forms. This process allows for the minimization of the negative influence on the environment, but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and it may be carried out in fluid bed furnaces.Oxidizing roasting of the concentrates in the presence of soda results in formation of water-soluble compounds and forces practically all arsenic and sulfur to remain in the cinder."

Jan 1, 2003

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

By Alan Bye, Nick Beaton, Wayne Stange, Emmy Manlapig, James Groutsch

"For over 50 years the JKMRC has applied a unique education-based research strategy to develop modelling and simulation tools that are "fit for purpose" for industrial application. These tools are widely used for the analysis and optimisation of mining and mineral processing systems. As the mining industry context evolves to deal with declining head grades, falling commodity prices, professional skill shortages, and an exponential growth in the volume of data, a re-evaluation of what "fit for purpose" means in the future is required. It is contended that future industry needs for simulation-based decision support requires tools and systems that incorporate: • Multi-component modelling, • Models of complex sensor behaviour, • Integration across the physical value-chain e.g. resource to market, • Financial analysis including risk and uncertainty assessment, • Enabling multi-criterion decision making (technical, financial and environmental), • Ore-body knowledge at multiple scales, • The use of fundamental numerical models to provide insight for the development of practically useful models, and • Decision support delivered through remote operations centres. JKMRC and CRC-ORE are collaborating to develop a next-generation simulation-based decision support system that assists in addressing these challenges. The Integrated Extraction Simulator (IES) combines many years of pragmatic and successful work integrated with modern technology trends - in particular the rapid move to cloud-based computing."

Jan 1, 2014

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

By R. K. K. Mbaya

The concept of adsorption or separation of platinum anions from base metal cations in chloride media using native or chemically modified activated carbons has been discussed in various journals within the context of batchwise systems. In our research work, a fixed-bed column, loaded with native and amine-immobilized activated carbon pellets (Norit RO 0.8), was used to study selective adsorption of platinum ions from chloride media at different flow rates, bed depth and initial metal concentrations. The kinetics, mass transfer characteristics, breakthrough data and separation factors (ß(Pt/Fe) and ß(Pt/Cr)) were quantitatively analysed and modeled. The bed-depth service time (BDST) model was used to model the breakthrough curves successfully in fixed-bed columns and also the dispersive diffusion in the radial and axial directions of the bed were evaluated. The inner diameter of the column was 3 cm and the bed depth was between 1.0 cm and 2.5 cm. Concentrated 4 M HCl acid solution was used to elute the fixed-bed column. It was demonstrated that amine-treated activated carbons provides superior separation factors between platinum and base metals (Fe, Cr). Results showed also, that 95% saturation was reached within 10~26 hours depending on the nature of ACs at a flow rate of 11 mL/min and initial concentration of 5 ppm.

Jan 1, 2014

By Patricio Berrios, David Barriga, Peter Amelunxen, Gerson Sandoval, Roger Amelunxen

Laboratory test equipment and methods have undergone relatively little change since their introduction in the 1950’s. The Denver sub-A cell is still by far the most commonly used laboratory batch cell, but bottom-driven and instrumented cells are beginning to appear. Test procedures have also changed little over the past 60 years, and most engineers continue to rely on empirical models for predicted plant scale performance from laboratory scale tests. This approach is problematic, because changes in the froth phase characteristics in the lab hamper the reliability and reproducibility of the empirical extrapolation to plant scale. In a previous work, the authors reported on the impact of froth recovery at the laboratory cell, showing that variability in the froth recovery can lead to significant error in the modeled kinetic rate constant unless it is properly accounted for in the scale-up model. In this work, we review the role of hydraulic entrainment in the lab cell, and how variability in particle specific gravity, shape factor, and froth residence time can impact the entrainment recovery.

Jan 1, 2014

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014