Search Documents

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

By Markus A. Reuter, Yongxiang Yang, James R. Post

The packed coke bed in the lower part of an iron making blast furnace, the dead man, dissolves slowly in a pool of hot metal, which is tapped regularly. The coke particles of the dead man not only exhibit a size distribution, but also their size distribution is non-uniform throughout the dead man and as a result, the porosity of the dead man is non-uniform. This causes the flow of hot metal through the dead man to be irregular and non-uniform, bringing about channelling in the coke bed. Channelling is detrimental to the refractory lining life of the hearth of a blast furnace. Using population balance modelling and a porosity model it is possible to keep track of the local changes in size distribution and bed porosity during dissolution of coke particles. Numerical simulations show that carbon dissolution from a packed coke bed (with particles which exhibit a size distribution) increases the average porosity, decreases the mean particle size and changes the size distribution to a distribution with a smaller size range. Influence of the type of initial size distribution (mean, variance) is investigated. The calculated changes in porosity are used to dynamically adapt the flow and the mass transfer (kinetics) during calculations. This approach provides the possibility to implement dynamic porosity calculations for CFD applications, and thus simulate the results of various coke types and particle size distributions on dissolution and flow behaviour.

Jan 1, 2003

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

By G. Bulut

The aim of this study is to produce desiccant clay from a well known Ca-bentonite deposit in Turkey. Towards this aim, bentonite samples were first procured and then subjected to some characterization tests. Various methods were applied to enhance the moisture adsorption capacity of bentonites to a desirable level. These methods include utilization of some additives namely calcium chloride and heat treatment at various temperatures. It is shown that the moisture adsorption capacity Ca-bentonites without any additive are between 14%~17 % (w/w) upon by heat treatment whereas the addition of calcium chloride significantly, raised the moisture adsorption capacities.

Jan 1, 2014

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By S. Kelebek, A. Khan, J. Caceres, Beckett. D.

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance. The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents."

Jan 1, 2003

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By T. Chmielewski

Unique mineralogical and petrological properties of black shale in the copper ore deposit of the Foresudetic Monocline (SW Poland) resulting from three lithological layers have been described in terms of its unfavorable behavior in the ore processing circuits. A concept of processing of a part of the black shale fraction from the flotation circuit of the concentrating plant by separating a by-product enriched in the shale matter was presented. This by-product represents the tailings of the first cleaning flotation and, as a hard-to-treat circulating middlings, overload the cleaning operation in the flotation circuit. It was found that the investigated by-product cannot be effectively up-graded using standard xanthate flotation. This is due to a fine dissemination of sulfide minerals in the dolomitic and clay shale particles significantly enriched in organic carbon. The content of the organic carbon is similar to that in the petrographically "pure" black shales. After a comprehensive examination of the shale by-product it was recognized that the investigated middlings can be regarded as a specific shale concentrate for individual processing. The effect of non-oxidative leaching of middlings with sulfuric acid on their further flotation was presented. It was shown that non-oxidative leaching is a selective process, in which calcium and magnesium carbonates decomposition leads to effective liberation of sulfide minerals which were finely disseminated in the hydrophilic carbonate gangue. Leaching of the flotation feed with sulfuric acid selectively decomposes carbonate minerals and consequently enhances flotation results. Saturation of leaching slurry with gaseous carbon dioxide favorably creates non-oxidative conditions and leads to a great decrease of the electrochemical potential of sulfide particles as well as hinders their solubilization. Partial carbonates leaching from middlings resulted in evident liberation of valuable minerals. Consequently, it resulted in an increase of both recovery and grade of concentrates obtained by flotation of shale by-product after non-oxidative leaching.

Jan 1, 2014

By L. M. Wang

Chengmenshan Copper Mine Concentrator adopts the new process of preferential?bulk stage floatation and utilize reground, largely increase the mineral processing index of the copper and the sulphide concentrates. In addition, the paper describes the remarkable economic benefit of the new process through the comparison of the new and the old processes.

Jan 1, 2014

By Polezhaev S. Yu, I. V. Ukraintsev, Boduen A. Ya, Saburbayeva L. Yu

"Comparison studies of different technologies are performed when selecting optimum option for gold ore and concentrate processing. Methods of ultrafine grinding, oxidizing roasting, bacterial leaching and pressure oxidation are used to extract gold from refractory ores and concentrates. Refractory gold flotation concentrate produced from pyrite-arsenopyrite ores of Bestobe deposit is a case study in this paper. The results of the experimental tests of the direct leaching of flotation concentrate and pre-oxidation products using different methods (oxidizing roasting cinder, pressure oxidation and bacterial leaching cakes) are the following: - cyanidation of original flotation concentrate provides recovery of Au at 46.6 %; - oxidizing roasting increases gold recovery from 46.6 % to 85 %; - BIOX increases gold recovery up to 86 %; - preliminary pressure oxidation of flotation concentrate ensures steadily high Au extraction in the follow-up cyanidation at 94.9-96.5 %. Pressure oxidation and bio-oxidation has changed dramatically the strategy of refractory gold ore processing. These solutions provided for development of ore deposits that considered earlier non-commercial. However, refractory ore processing has a complex character in terms of developing process flowsheet and requires large amount of studies to be performed for each new project. Gold extraction is the basic but not the only criteria to technology selection for gold ore and concentrate processing. Opex and capex, ore reserves, regional geography, developed infrastructure and skill personnel should be considered. Process studies and feasibility study of the developed technology shall be provided for each specific gold ore deposit. INTRODUCTION Due to changes in available feedstock and depletion of easy-to-process ores, refractory ores containing finely disseminated gold and silver in sulphides (primarily, in pyrites and arsenopyrites) are more and more involved into processing. Experts say that such ores amount above 40 % of the world’s gold reserves. Conventional technologies of gold extraction from refractory ores include flotation, roasting and cinder cyanidation (Fraser etal., 1991). However, today’s best available practice for refractory gold ore processing are bacterial (BIOX) and pressure (POX) oxidation."

Jan 1, 2018

By J. Y. P. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Hongchun Lou, Yan Zhang, Xianjun Lu

"The potential of Fe(NO3)3 modified attapulgite was assessed for the adsorption of phosphorous removal from aqueous solutions. Natural attapulgite was modified by Fe(NO3)3, and thus the composite adsorption materials could be obtained. Also phosphorous adsorption characterization on the iron-coated attapulgite was investigated in this research. Taken overall the results suggested that phosphorous adsorption capacity could be improved markedly by adopting ferric modified-attapulgite. The optimum phosphorous adsorption were developed in the experimental conditions of the solid-to-liquid Ratio 1g/L, the initial phosphorous concentration 5 mol•L-1, reaction time 120 min, temperature 25 ? and pH=4.0, the removal efficiency is 92.28% for the modified attapulgite. In comparison of batch experimental results of phosphorous adsorption onto natural and iron-coated attapulgite, it has provided much more likely the same change trend. On the other hand, the outcomes of this analysis indicated that ferric modified adsorbent was notably influenced by adsorption element over natural attapulgite. The Freundlich isotherm adequately described the adsorption course of phosphorous onto ferric modified-attapulgite with the correlation coefficient R2 goodness of fit of 0.9690."

Jan 1, 2014

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By C. H. Veloso

"Starch is the most widely used depressant in the reverse cationic flotation of iron ores. There is however, an indication from recent studies, that other polysaccharides may successfully replace them. When starches are used in the flotation of iron ores in the presence of quartz as gangue mineral, their strong adsorption on the surface of iron oxides can be explained by the molecular conformation between the available sites on the mineral surface and two hydroxyls of starches. However, when the gangue minerals are iron-bearing silicates, the strong interaction with starch can occur on these minerals since they have the same surface behaviour as iron oxide. In this work bench scale tests were conducted in order to generate scientific knowledge about other alternatives depressants for the flotation of iron ores. A magnetic pre-concentrate from a skarn iron ore processing plant was used as feed material for flotation tests. The reverse flotation approach was used to upgrade the iron content by removing complex ironbearing silicates. The depressants used in this study were: corn starch, dextrin, carboxymethyl cellulose (CMC) and humic acid. The tests were performed under different pH conditions in order to try to relate the efficiency of depression to the pH used during flotation. The results show the important role of pH as each depressant reached its best performance at different pH values. At alkaline pH the corn starch showed best depression performance while the humic acid is more efficient at pH close to neutrality.INTRODUCTIONIron corresponds to approximately 6% of earth’s crust composition (McDonough and Sun, 1995). It is the most used metal in our lives, some of its properties as resistance and facility to be shaped makes is replacement very difficult. The primary sources of iron on our planet are minerals. The iron-bearing minerals most commonly found in nature and economically exploited are magnetite [Fe3O4], hematite [Fe2O3], goethite [FeO(OH)] and siderite [FeCO3] (L O Filippov et al., 2014). These minerals are commonly associated with other minerals (most of the time not economically exploited) forming the so-called iron ore. Iron ore is the source of primary iron for the world’s iron and steel industries."

Jan 1, 2018

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014