Search Documents

By Arkady Senchenko, Andrey Vasiliev, Alexander Aksenov, Metodi Zlatev

"This paper considers the issue of treating argillaceous oxidized ores with low gold grade (around 1.0 g/t). These ores according to their gold recovery level can be treated by heap leaching and agitation cyanide leaching, but low gold grade makes this treatment uneconomic. Heap leaching of argillaceous ores requires high consumption of binding agent for pelletizing to create suitable hydro-physical properties of material, which leads to increasing process cost and makes the material treatment unprofitable. Agitation cyanide leaching of this ore requires grinding processes; these expenses would not be paid back by the amount of gold recovered. Considering the above, poor argillaceous oxidized ores are recommended to be treated according to a combined technology including fractionation of ore, heap leaching of coarse fraction and agitation leaching of argillaceous fraction. Complex approach application allows one to avoid expenses incurred for material grinding and high consumption of binding agent for pelletizing. The success of this technology implementation will firstly depend on the quality of material fractionation, therefore the section of disintegration and division of ore into different components will be the most important part of flowsheet development for gold production. When disintegrating minerals at positive temperatures both standard (mechanical disintegration - scrubbers) and innovative (hydraulic method of disintegration - HydroClean units) equipment is applicable. HydroClean units are characterized by lower energy and water consumption. In a number of cases it is required to treat frozen ores. When treating frozen material standard approaches to disintegration are not reasonable due to their low efficiency. In order to treat frozen material a two stage disintegration flowsheet with screening after each stage is recommended. The first stage is recommended to be performed in a scrubber, the second - in a HydroClean unit. This technological flowsheet will provide high and steady values for ore separation into fractions at low energy consumption for disintegration."

Jan 1, 2014

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By Nilmara Dias, Maria Margarida Martins, Maria Teresa Carvalho

"The heavy residual fraction of the mechanical and biological treatment (MBT) plants treating undifferentiated municipal solid waste is mostly composed by inert materials, such as glass, stones, ceramics and brick. Glass, appearing in significant grade and amount, is not recycled today due to the high content in the other materials, mainly stones. All these materials have approximately the same density but stones have significantly different shape from other materials particles. In this paper it is presented the research developed to eliminate stones appearing in the fine fraction (2.8-8 mm) of the MBT plants heavy residual fraction (MBTr) using a shaking table operated in dry conditions. Two different samples from two different MBT plants were used. Firstly, the samples were characterized (materials content and particle size analysis). Then, laboratory work was carried out to optimize the operation of the shaking table, by changing the machine parameters, deck slope and movement frequency. The study showed that it is possible to upgrade the product in glass. The best results, obtained with one single stage of processing, were 82% content in glass with 84% in recovery, in the glass concentrate, when the coarser fraction (-8+5.6 mm) of one of the MBT plants was used. With the intermediate particle size fraction (-5.6 + 4mm), the glass concentrate attained 74% content in glass with 91% recovery."

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012

By David Verrelli, Melissa Kistner, Leanne Smith, Chris Aldrich, Lidia Auret, Warren Bruckard

In this investigation, different mixtures of realgar and orpiment particles were floated in a laboratory batch flotation cell and multivariate image analysis was used to estimate the arsenic content in the froths. The analysis was based on the froth colour, as well as extraction of three groups of textural features, namely those based on grey level co-occurrence matrices (GLCMs), wavelets and local binary patterns (LBPs). Collectively, these features provided better information on the arsenic content of the froths than any one of the individual groups of features. Partial least squares models could explain approximately 78% of the variance in the arsenic by using all the features combined. The colour content, particularly the green component in the red-green-blue (RGB) features, provided almost as much information as each of the three sets of texture-base features individually.

Jan 1, 2014

By Larry A. Cramer

"Three primary drivers are setting the trend for base and precious metal processing . they are: continued low real base metal prices, environmental concerns, and continued high prices for PGM.s. Low base metal prices are increasing the search for economies of scale and company consolidation as well as the development of some hydrometallurgical technologies. Environmental concerns are pushing for continued reductions in SO2 emissions and hydrometallurgical technologies. The high prices for PGM.s are driving major expansions and a focus on minerals processing recoveries and, to a lesser extent, reductions in the refining metal lockup.In nickel, HPAL operations on laterites have failed economically but Inco is still pursuing some alternatives. BHP-Billiton and others are developing bioleaching alternatives for nickel laterites and sulphides.Copper continues to be dominated by the hydrometallurgical and pyrometallurgical debate; new hydrometallurgical developments are being tested at several sites whilst the pyrometallurgists continue to make competitive cost and environmental improvements.Gold processing developments are dominated by the use of improved gravity recovery equipment and by the development of thiosulphate as a more environmentally acceptable lixiviant.PGM processing trends are the use of fine grinding technologies, higher power input flotation cells, and new pyrometallurgical technologies. Hydrometallurgical options for some applications are being sought.OVERVIEW The metals industry has remained under price pressure for some time; low and decreasing real prices for most metals have become an expected scenario. Occasional price spikes give some relief but invariably bring expansions and new entrants into an already oversupplied commodity market, thus leading to the continued price pressure. Technical innovation, economies of scale, and improved work systems are continually sought, so as to improve the competitive position of each individual company in such a climate; however, these developments add to the downward price pressure. In such a situation the application of scarce funds to research and development is a difficult task. Excess funding is not available in tight economic times and yet the main route to higher profits is clearly the application of technical developments to lower the cost of producing a metal commodity. Many technical centers have closed as a cost saving exercise and some have coalesced to obtain economies of scale. The Australian based AMIRA research organisation has grown to serve the R&D part of the market well in Australia and in South Africa by acting as the catalyst to form research partnerships between a number of industry players and as an administrator to direct the funding of research projects towards the various applicable research institutions. AMIRA has developed closer ties to Camiro (Canadian Mining Research Organisation) through the appointment of Camiro.s metallurgical processing research director as AMIRA.s North American based director. AMIRA is continuing discussions with MIRO (Minerals Industry Research Organisation) in regard to a merger, with a report outlining the merger proposal expected in March of 2003. Company focused research centers continue to be effective at Anglo American Research Labs, Teck-Cominco Research, Falconbridge Research center, Inco Research and some others."

Jan 1, 2003

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By H. Z. Kuyumcu

Associated with the development of a novel microbiological oxidation process for the conditioning of iron hydroxide slurries from ferrous mine waters, there is a realistic chance to make the contained iron available for a material utilization. The transformation of ferrous into ferric compounds is coupled with the precipitation of iron hydroxisulphate mostly in terms of the mineral Schwert-mannite. The further treatment of the iron hydroxisulphate has to be aimed on the processing for product recovery and product refinement. For many potential applications, e.g. in the ceramic industry, the pigment industry or for metallurgical applications, the removal of sulphate is essential. For the dehydration of the iron hydroxisulphate and the sulphate removal, microwave heating technology is a beneficial method. In contrast to conventional thermal heating processes the supply of energy in microwave application takes place directly within the material through the dissipation of electromagnetic energy, i.e. no heating medium is needed. It is a volumetric heating process regardless of the surface of the material. The rapid and targeted energy supply and the good controllability of microwave heating systems are advantages which have led to a wide variety of applications in industrial processes. Among the diverse use for heating of temperature-sensitive, chemical and pharmaceutical products as well as foodstuffs the number of applications also in mineral and solid processing increases. At the Department for Mechanical Process Engineering and Solids Processing of the Technical University Berlin the use of microwave technology for the treatment of iron hydroxisulphates has been investigated systematically within the framework of a cooperative research project. The paper at hand shows results from material conversion tests subject to a variation of the relevant process parameters. The reaction products are characterized and the process is compared with the conventional heating in a rotary kiln.

Jan 1, 2014

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

By B. Tora

The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. The essence of this method consists of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. The research equipment designed specially for this project is described New method of grindability measuring completes standard Hardgrove method withdrawing its faults: ? bigger (c.a. 10 times) and more representative sample is used; ? the milling process is carried out in close circuit (similarly to the industrial condition); ? energy consumption of the milling process is determined for three samples, which differs in grain size. The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. This method allows us to determine energy consumption of the milling process. The essence of this method consist of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. Our results will complete the Hardgrove method and will help us to better characterise coal. At the same time investigations in industrial scale are carried out. These investigations will verify this new method. Also a new mathematical model of the milling process is being elaborated. It will be used to predict behaviour of coals in industrial conditions.

Jan 1, 2014

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By Valentine Chanturiya1

We have developed a classification of geochemical barriers according to their origin, i.e. natural and artificial, and according to methods and areas of application. There has been an examination of the interaction between different classes of geochemical barriers with sulfate solutions containing nickel, copper and iron. As natural barriers, carbonates (calcite and dolomites) were used. For artificial barriers, a mixture of serpentine and carbonatite, thermo-activated copper-nickel dressing tailings, and a magnesium-containing sorbent based on brucite was used. Keywords: geochemical barriers, physical-chemical geotechnologies, treatment of natural and waste water, recovery of nonferrous metals

Sep 1, 2012