Search Documents

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

"INTRODUCTIONThis paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.OPTIMISATION MODEL FOR LINKING DESIGN TO RECYCLINGImproving the efficiency of the material cycle of the car is essential to ensure a sustainable development of our society as well as e.g. to comply with the recycling targets imposed by EU legislation. In the design of the car various materials are combined and connected in many different ways, making up the complex 'mineralogy' of the car and its components, which is changing rapidly and continuously over time. The liberation of materials during shredding plays an important role in the composition (and quality) of the intermediate recycling streams. In order to include the influence of product design (mineralogy), liberation, and particle composition (quality of the intermediate recycling streams) in the optimisation of the recycling of end-of-life vehicles, a systems engineering tool for optimisation of the recycling of end-of-life vehicles was developed, including a liberation model. The optimisation model predicts the recovery rate as a function of product design (in this case a car), liberation, efficiency of the different process steps, economy and legislation based on a developed recycling flow sheet for end-of-life vehicles. Optimisation can only be achieved through the combination of the knowledge areas of product design, shredding, mechanical separation technology linked to pyro- and hydrometallurgy, composing a complex interconnected network of unit operations."

Jan 1, 2003

By Vladimir Vigdergauz

"Electrochemical studies of metal sulfides in connection with their floatability are discussed. According Frumkin, sorption of electroneutral organic substances has a maximum near the potential of zero charge. This idea initiated attempts of application of electrochemical methods for the controlling of organic collector sorption and mineral flotation. The lecture reviews results of electrochemical studies of the processes taking place during sulfide flotation: redox-state of mineral surfaces and xanthate solutions, xanthate sorption and hydrophobic layer composition, surface wettability and flotation recovery of sulfide minerals. Redox-transitions of minerals, transport of ions and charging of mineral surfaces, electroreduction of dissolved oxygen and accompanying processes of oxidation of minerals and reagents-collectors, - all these matters became the subjects of detailed research. Cyclic voltammetry, rotating disk electrodes, spectro-electrochemical techniques and other modern experimental methods now routinely accompany studies of mineral processing. Relatively new electroanalytical techniques like the voltammetry of mineral particles immobilised on electrodes using polymeric binders have become extremely useful for studying weakly conductive minerals and dispersed flotation products. Full discussion of electrochemical studies of metal sulfides in relation to mineral processing must include bioelectrochemistry and electrocatalysis which open exceptional possibilities for selective leaching of gold and non-ferrous metals. At this time, the paper focuses on the sulfide flotation as a potential-dependent process; the problem of oxygen and its influence on the sulfide flotation; the electrochemical aspects of xanthate oxidation and sorption; theory of suspended electrodes as applied to the mineral slurries and experimental study of the effect of electrochemical pretreatment of flotation pulps."

Jan 1, 2014

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The methodology is to use plant data to build the models and to supplement this by laboratory data where necessary, for example the determination of breakage functions. The plant data come from comprehensive sampling surveys and so far 33 surveys of clinker grinding circuits have been carried out in 9 plants. The operating conditions have been• mill sizes – 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,• mill feed rates – 46 to 158 tonnes per hour,• air flow through mills – 25000 to 125000 cubic metres per hour,• cement clinker work indexes – 10.3 to 18,• separator sizes – 2. to 3.1 metres diameter,• separator feed rates – 132 to 689 tonnes per hour,• separator speeds – 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises on the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distributiongraphs are used to illustrate every aspect of the discussion.In case I the special emphasis on calculating the breakage rates and discharge rates separately is given in a high pressure grinding roll-ball mill-separator circuit. The tonnes of each size fraction in the mill and the calculated values of R/D, D and R are determined. The values of R per mw are also given to allow comparison with mills of other sizes. The circuit allows the comparison of the static type (V Sep) and dynamic type separators (SKS). Comparing the reduced efficiencies shows that the dynamic separator is slightly more efficient than the static one.In case 2 data are given from two compartment tube mills having the same diameter and the motor power but different ball size gradation. The breakage rate particle size variation of the second chamber of two mills indicate that having finer ball size distribution causes higher breakage rate values."

Jan 1, 2003

By C. Suazo, N. Mora

"The bubble size distribution plays a fundamental role in flotation kinetics. Nowadays it is possible to measure the bubble size distribution, gas holdup and superficial gas velocity by using specialized equipment developed for this purpose. In this article a methodology is presented for estimating the kinetic rate constant using a known particle and bubble size distributions. The attachment and detachment probabilities were modelled from three matrixes. The first matrix represents particle size distribution, the second was named the probability matrix, and the third is the bubble size distribution. Using laboratory data, it has been possible to estimate the flotation rate constant as a function of operating conditions and both the bubble and particle size distributions. The model tested at laboratory scale achieved a quadratic correlation coefficient equal to 0.97. This methodology could be used in the operation and control of the flotation, when in the near future we have industrial equipment that allows in-line measurement, in real time, of gas dispersion and bubble size distribution. knowing particle size distribution, it will be possible to manipulate the operating flotation cell conditions, in order to modify the bubble size distribution and find the bubble distribution that maximizes flotation kinetics. Furthermore, knowing the bubble size distribution, the grinding operator will be able to look for the particle size distribution that produces the maximum flotation kinetics. In order to do this, the operator will have to modify the solids percentage fed to the hydrocyclone cluster, modify the apex/vortex ratio, etc. Finally, this article shows that the maximum flotation speed is reached when the particle size distibution slope is equal to the bubble size distribution slope."

Jan 1, 2014

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By Graeme Lane, Yuqing Feng, Kaixi Jiang, Junwu Zhou, Zhengchang Shen, Tao Song

"Airlift reactors are used in a wide range of industries, such as hydrometallurgy, biochemical processes, chemical process industry and waste water treatment. With increasing superficial gas velocity three circulation regimes can be defined: no gas bubbles in the downcomer, gas bubbles remain stationary in the downcomer and gas bubbles in the circulating regime. In this paper a numerical modelling method was presented for gas-liquid flow in airlift reactors under different bubble recirculation regimes. Gas-liquid flow was modelled using the Eulerian two-fluid equations, and extra user defined subroutines were incorporated to consider the complex physics, such as bubble induced turbulence and turbulent dispersion force. Some alternative correlations of drag coefficient were used to capture the bubble distributions in the riser and downcomer of the airlift reactor, with consideration of the interaction between bubbles. As using constant bubble size is hard to describe global characteristics of the flow in airlift reactors for three circulation regimes, a model including multiple bubble sizes was presented to get more accurate simulation results of gas holdup and water velocity. Also, the inhomogeneous MUSIG model was used, as an exploration, to compute the complex flow regimes. The MUSIG model is a population balance method to predict the bubble sizes, taking break-up and coalescence into account. The modelling method was applied to a laboratory internal loop airlift reactor, and the simulation results were compared with the experimental measurements of Simcik et al. (2011) for gas holdup and water velocity. The three bubble circulation regimes were observed from simulation figures. Reasonable agreement was obtained over a range of operating conditions, and an improvement was demonstrated using the proposed methods."

Jan 1, 2014

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014