Search Documents

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By H. Sarvamangala

Selective separation of alumina, silica, calcite and apatite from hematite was achieved through microbiologically induced flotation and flocculation in presence of bacteria (B.subtilis) and that of hematite from apatite after interaction with yeast (Saccharomyces cerevisiae). Bacterial and yeast metabolites containing extracellular proteins were characterized from mineral-grown cell free extract. Bacteria and yeast can adhere to mineral surfaces and influence subsequent separation of the minerals. Bacteria functioned as a stronger depressant for hematite, while yeast cells depressed apatite at neutral pH. Selective affinity of the bacterial and yeast cells towards the mineral surface was observed through adsorption studies. Extracellular proteins (EP) were isolated from B.subtilis and yeast. The protein profile of the EP of bacterial and yeast cells grown in presence and absence of minerals was studied. This study has demonstrated the utility and amenability of microbially-induced mineral beneficiation of iron ores through bacterial and yeast cells and their metabolic by products.

Sep 1, 2012

By Liang Dianyin

In this paper, the molybdenite flotation tailing of cleaner-scavenger bank which has a mass of very fine particles has been taken as raw ore to be processed by flotation with/without ultrasonic. The effect of ultrasonic frequency, intensity, processing time and uploading location on molybdenite flotation efficiency is investigated by four-factor three-level orthogonal experiment, and the effect significances of these ultrasonic variables to molybdenite flotation efficiency have also been evaluated. Single-factor analysis of variance is conducted to investigate whether the effect of ultrasonic on molybdenum ore flotation efficiency is significant or not. The samples extracted from different ore species in different time have been mixed to analyze the particle size. The results show that the particle size of +38µm in concentrate obviously increases while the particle size of -25µmobviouslydecreaseswith ultrasonic, which means that ultrasonic is good for flotation due to sludge removing effect. Keywords: ultrasonic, flotation efficiency, sulfide ore, tailing, grade, sludge removing

Sep 1, 2012

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"Over the past few years CSIRO Minerals has been conducting research aimed at developing a continuous copper converting process to replace the traditional two-stage batch process that is currently used to produce blister copper. Sirosmelt type reactors and calcium-ferrite (lime-based) slags have been used rather than the conventional iron silicate slags. The research work has now been extended to focus on the development of a single-stage continuous copper making process (so-called direct copper converting) in which copper concentrates are converted to low-sulfur blister copper in a single step, that is the smelting and converting steps occur in one continuous stage.One feature of the direct copper converting process is that copper losses to the slag phase can be high, meaning the slag produced needs to be treated to recover the copper value. The feasibility of the whole copper making process will most likely depend on the efficiency and cost effectiveness of the copper recovery stage. Flotation has been identified as the most economical option to recover the copper from direct copper converting slags where it has been estimated that a copper recovery from the slag of above 90% is required to make the overall single stage copper making process economically feasible.A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. Copper sulfide concentrates from MIM were used as feed-stocks. The objectives of this work were to develop a robust flotation process to maximise the copper recovery and iron rejection from slags made in the process, and to establish operating conditions for future continuous flotation pilot plant trials.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu and the CaO/Fe ratio varied between 0.30 and 0.54. In general, the higher the copper content the more oxidised the slag. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases. Reagent additions were typically 200 g/t KEX and 500 g/t Na2S.9H2O and the grind size was generally a P80 of about 40 µm."

Jan 1, 2003

By Hossein Zarei, Masoud Kashani, Mehdi Safari

The feed of flotation unit in Angouran mine, as a part of Iranian Lead and Zinc National Corporation, contains about 34.26% zinc (about 12% Zn sulphide) and 10.14% lead (about 2% Pb sulphide). The grade of Pb and Zn in the final concentrate (rougher+scavenger), under optimal conditions (200 g/ton PEX, 500 g/ton zinc sulfate, 30 g/ton MIBC and pH = 7.5), was 63.18% and 13.01%, respectively, and the total Pb (sulphide-oxide) recovery was about 19% which included 95% Pb sulphide. The grade of Pb and Zn in rougher concentrate step was about 71.86% and 5.97%, respectively, when PEX (Potassium Ethyl Xanthate) was used as collector. While in the presence of PAX (Potassium Amyl Xanthate), the grade of Pb and Zn in rougher concentrate step was 66.8% and 10%, respectively. Tailing of the galena flotation (with 8.48% Pb grade and 34.92% Zn grade under the optimal conditions) was used as a feed for sphalerite and oxide section flotation.

Jan 1, 2014

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

Reverse flotation process tests were conducted for marine sedimentary silicon-calcium phosphate ore in this research. The research findings showed that by adding antifoamer, a concentrate with P2O5 32.36%, SiO2 10.69%, MgO 0.67% was obtained, with recovery of P2O5 being 88.12%. Such is a satisfying result, when compared with the original mineralogical component of P2O5 26.64%, SiO2 11.51% and MgO 3.36%. When using antifoamer, the SiO2 grade of the concentrate increased 0.55%, the MgO grade decreased 0.64%, while P2O5 recovery increased 2.69% compared by adding no antifoamer. Adding antifoamer is favorable to increase the grade and recovery of P2O5. Therefore, antifoamer is necessary. Tests of synergistic reaction of antifomer indicate that the appropriate consumption of the antifoamer is 275g/t CY and 1Kg/t TWF. Keywords: silicon-calcium phosphate ore, desilication, antifoamer, reverse flotation

Sep 1, 2012

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By H. Deng

Oxidized zinc ores are the main source of zinc metal except sulfides. To have a better understanding about the performance of smithsonite and the main gangue, quartz, in flotation, the aggregation behaviors of smithsonite and quartz in water were confirmed by different techniques (sedimentation tests and optical microscopy). The experimental results show that smithsonite and quartz particles aggregate in the pH range 7.5-11. The results of zeta potential suggest that the aggregation does not correlate with the DLVO theory, when the iso-electric point of smithsonite and quartz is 8.0 and 2 respectively. When the solution pH is less than 8.0, smithsonite has an opposite charge to the quartz particles. Electrostatic adsorption makes effort on these two kinds of particles according to DLVO theory. Whereas, solution chemistry calculation shows the pH range 8-11 corresponds to hydroxide formation, suggesting that this is the species responsible for aggregation. And their concentrations are much higher in sodium hydroxide system than that in sodium carbonate system. Aggregation of smithsonite and quartz due to the flocculation action of zinc hydroxide is proposed.

Sep 1, 2012

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014