Search Documents

By Massimiliano Zanin, William Skinner, Owusu Clement, Jonas Addai-Mensah, Daniel Fornasiero

This paper highlights the importance of pulp aeration in the selective separation of chalcopyrite from chalcopyrite/pyrite mixtures of varying pyrite content (20-80 wt.%). Laboratory batch flotation studies and oxygen demand tests were performed to predict the optimum amount of air required for the selective separation of chalcopyrite from pyrite. The pulp oxygen demand was shown to increase with increasing pyrite content but decrease with time as more air is introduced into the system. Complementary batch flotation tests showed significant improvement in chalcopyrite flotation under moderate pre-aeration of the pulp. However, a continuous decrease of chalcopyrite flotation was observed under highly aerated conditions. The amount of air required to achieve maximum chalcopyrite flotation recovery correlated positively with the mass fraction of pyrite in the pulps. The greater the wt.% of pyrite in the chalcopyrite/pyrite pulp, the longer the aeration time required. The optimum aeration time was established as the time before which the oxygen consumption rate constant reaches a bottom plateau. Surface analysis (XPS) indicated that the continuous decrease in pyrite recovery observed with increasing aeration time was due to the formation of more iron oxy/hydroxide on its surfaces, the same species accounting for the decrease in Cp recovery after prolonged aeration.

Jan 1, 2014

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By Jan Cilliers

The demand for minerals has never been higher. Moreover, the rate at which this demand is growing is unprecedented, and expansions and new mines will be required to fulfill these growing needs. This, in turn requires a skilled engineering workforce that can develop and operate minerals extraction processes to utilise effectively more complex ores. The International Mineral Processing Council (IMPC) has established a Commission on Mineral Processing Education to consider the global challenge of ensuring an adequate supply of well-trained mineral processing engineers. The Commission has, for the past four years, been collecting international information of the recent mineral process engineering supply position and with a view into the near future. The data collected by the international Commission members are as follows: ? Undergraduate student numbers in minerals engineering ? A breakdown of their male/female ratio ? The fraction of the students from each course that enter the minerals industry ? Teaching staff numbers and age profile This data has been collated and analysed, and the findings are presented. It is clear from the analysis that the supply situation is very different in different regions of the world, and that great opportunities exist for targeted recruitment into the industry to meet the future talent demand. Further, an attempt at correlate the supply of minerals engineers based on the local mineral production rate is shown, which shows that there are clear outliers.

Sep 1, 2012

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By R. Marandi

The effective removal of heavy metals from aqueous wastes is among the most important issues for many industrialized countries, How ever biosorption, i.e. the uptake of heavy metals by non- living biomass, has gained increased credibility during recent years. Biosorption of Cr(VI) from aqueous solution, on pretreated and immobilized Aspergillus niger was investigated in a batch and countinuous reactors. A.niger biomass pretreated by boiling in 0.5 N NaOH solution for 15 min, exhibited higher Cr(VI) removal capacity than autoclaved biomass. The optimum adsorption pH value observed for Cr(VI) ions was 2. The Cr(VI)removal rate increased with a decrease in pH. The influence of contact time, pH, Cr(VI) concentration, biomass concentration and temperature on Cr(VI) removal were also evaluated. Biosorption of Cr(VI) on pretreated biomass followed the Freundlich and Langmuir adsorption models.In this study A.niger biomass was immobilized in Na-alginate matrix. The biomass beads packed in a column were able to remove metal ions.In this study we used two different flow rate in a column, 1.5 mL/min and 3 mL/min.The breakthrough data obtained for Cr(VI) was adequately by the Thomas and Yan models and the adsorption capacity of the biomass was found to less than the adsorption capacity obtaind in the batch study. When the beads containing biomass become saturated with metal ions, the adsorbed metals were eluted using 0.5 N NaOH solution. Therefor nearly 90% of Cr(VI) was desorbed by NaOH solution.

Jan 1, 2014

By Avishan Atrafi, Marek Pawlik

"Gas dispersion properties of sodium salts of 6, 12 and 18-carbon fatty acids (hexanoic, lauric and oleic acid) were investigated as a function of pH. A strong effect of pH was observed on gas dispersion properties of fatty acids. At high pH for 12 and 18 carbon fatty acids, at which these surfactants formed a true solution, the gas dispersion properties were similar to those of MIBC. In the case of sodium hexanoate, which has a much higher solubility than the longer chain fatty acids and therefore does not form precipitates, the gas dispersion properties of this surfactant were strongly enhanced in the acidic pH range, where hexanoic acid was fully associated. This result is an indication that undissociated hexanoic acid is much more surface-active than anionic hexanoate. Only a small effect of the surfactant chain length on gas dispersion properties of the tested reagents was observed. The measured critical coalescence concentration (CCC95) values increase slightly by decreasing chain length and range from 5.8 x 10-5 mol/L (17.7 mg/L) for sodium oleate to 7.2 x 10-5 mol/L (16 mg/L) for sodium laurate at pH 10 and 1.9 x 10-4 mol/L (26 mg/L) for sodium hexanoate at pH 3.7. These are compared to CCC95 of MIBC, which is measured to be 8 x 10-5 mol/L (8 mg/L). The soluble molecular species were recognized as the most effective species in preventing bubble coalescence."

Jan 1, 2014

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By R. Paturi

Mill liners play an important role in the operation of a mineral concentrator influencing the throughput, availability, power drawn and the efficiency of the mill in the plant. Liners protect the shell and transfer energy to the grinding charge. Metso Technology Development has conceptualized, developed and successfully implemented physics based 3D DEM simulation techniques to predict charge motion, power drawn, energy spectra and wear over the life of the liner. This paper will present a case study of shell liner optimization for a 34? SAG mill including the input data requirements, and shell liner optimization methodology using the 3D simulations that eliminates the need for the traditional expensive and lengthy proto-type testing. These simulations will cover ball and particle movement, liner wear and mill power draw, and do not cover particle breakage and slurry flow. Even the liner manufacturers lack the ability to provide this type of qualitative and quantitative information on their products. The data from these simulations provides the plant engineers a scientific basis for their decision making and thus eliminates guess work. Keywords: liner, optimization, multi-physics, 3D-DEM

Sep 1, 2012

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By Konstantin Fedotov, Victor Beloborodov, Anatoly Potyomkin

"There are areas in Russia, which cover huge territories and they are north, and Siberia. These difficult to access regions with cold climate are rich in a great number of distant deposits of valuable and rare metals, gold and platinum. The development of such deposits requires highly effective technologies of mineral processing which could be realized in modular and quick-built processing plants.The work presented includes the results of long term research in the development of new technologies of processing of zirconium (in the form of rare mineral Baddeleyite – natural zirconium dioxide) bearing ore of the Kovdor deposit which is located in the Polar region of the Kola peninsular and also in Siberia deposits of of ledge ores of gold."

Jan 1, 2003

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014