Search Documents

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By H. G. Hedlund

Tailings in Mining Industry can be handled in different ways. Today tailings disposal is in focus by projecting new plants as well as treating and handling of old Tailings dams.The trend today is to process minerals, detoxify the Tailings and place them as dry surface Deposition or Underground Backfill. This paper will briefly present five different Mining plants in North and Central America, where Tailings have to be dewatered for dry depositing. The Metso-Sala VPA is a filter especially developed for dewatering and drying of Mineral Concentrate and Mineral Tailings. Keywords: tailings disposal, dewatering, drying, mineral tailings

Sep 1, 2012

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Claudio L. Schneider, Reiner Neumann

Any serious study of stereological conversion procedures must be based on an as accurate as possible complete fractionation of a real mineralogical texture. The original work on the Dolomite- Sphalerite Magstream? separation provided excellent data for establishing a working stereological conversion procedure, which has been successfully applied to a number of ores since its implementation. The linear grade distributions measured from these fractionated particles have been published and are accessible. The procedure for stereological conversion from areal measurements is exactly equal to the procedure for linear measurements. Particle composition from the dolomite-sphalerite density-fractionated particle sets, derived from both linear and areal data (Figures 1 and 2, respectively) are redundant, after proper transformation, and match the particle’s compositional range (plotted against S.G.) expected from Magstream?; direct density measurements by Hemicropicnometry plots within the ranges. Linear data cannot be used without conversion, but areal measurements are often directly applied as liberation spectra. Our areal measurements, without stereological conversion (Figure 3), differ completely from the results after transformation, and its density range falls mostly out of the expected/measured values. Therefore non-transformed areal data cannot be directly applied as useful liberation information.

Jan 1, 2003

By A. Mainza, H. Hill, L. S. Bbosa

"Impact breakage is the most elementary size reduction mechanism in comminution devices. In comminution research, characterization of breakage is primarily concerned with the energy expended to cause it. The main challenges of this approach have been quantifying the actual energy requirements of impact breakage and developing mechanistic models to accurately describe the process. For engineering load analysis, fracture is characterized in terms of strengths such as yield stress and ultimate tensile stress, which govern the maximum loads specific materials can be subjected to before irreversible inelastic deformation and subsequently complete fracture occur. With this approach, the main challenge has been to elucidate the underlying mechanism, in the means that the load causes weaknesses in the material microstructure to act as sites for stress concentrations, leading to crack initiation, propagation and eventual failure. Studies dedicated to investigating particle fracture under impact loading have led to the development of several devices for conducting breakage characterization tests. These devices include the drop weight tester, split Hopkinson pressure bar, rotary breakage tester and the short impact load cell. All these have different particle loading and breakage methods, and thus can yield distinct information which can be compiled together to study a material and the nature of breakage. This work analyses the single impact breakage data obtained across the listed devices. A homogenous ore commonly known as blue stone is used for all breakage tests. The work is conducted using standard procedures specific to each device as closely as possible. Drop weight and rotary breakage tests were used to obtain hardness parameters based on an existing t10 breakage model, while split Hopkinson pressure bar and short impact load cell measurements provided properties based on conventional engineering load analysis. The results were used to highlight the significance of the loading geometry, impact mechanism and impulse on the extent of breakage."

Jan 1, 2018

By Lev Filippov, Lorène Dessalas, Inna Filippova, Yves Foucquet

"Seafloor massive sulphide (SMS) deposits, similar in composition and genesis to terrestrial volcanogenic massive sulphide deposits, are generally found in volcanic seafloor environments along major rifts and mid-ocean ridges. Theyare associated to extensional tectonic settings such as nascent-arc, rifted-arc and back-arc environments. They may represent important source of base metals and be an alternative to on-land resources. Seafloor massive sulphide deposits have particular mineralogical compositions and textural features differentiating them from terrestrial one. When extracted from salty water and exposed to the ambient air, massive sulphide samples strongly oxidize and soon become covered by thin layers of iron, copper and zinc rich sulphates and oxides, as well as elemental sulphur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. The total porosity of that type of samples is also relatively high, especially for immature samples such as black smoker chimneys, which can reach 15% of total porosity. Because the secondary mineralization and porosity level are different, seafloor massive sulphides ores respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all type of sulphides from the gangue, is one possible technique for processing seafloor ore. Sulphide recovery rate is, in most cases, excellent (>90%) however separation of the various mineral phases is difficult to obtain even when applying known methods used for terrestrial ore. Moreover, the flotation behaviour decreases drastically with the time of conservation at the surface, even when the samples were stored in a confined environment. High pH values, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulphides, do not have the same effect on seafloor ore. Consequently, careful flotation procedure must be elaborated to obtain efficient mineral separation technique for this specific marine ores."

Jan 1, 2014

By C. Hazotte, M. -O. Simonnot, V. Houzelot, B. Laubie, M. Guilpain, B. Jally

"More than 400 plants in the world are able to accumulate nickel (Ni) in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, Ni can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and producing metal. It has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Hydrometallurgical processes have been designed; two different pathways were developed: i) acid leaching of ashes after biomass combustion and ii) direct Ni water extraction after biomass grinding. Experiments with 2 species of Ni hyperaccumulators (A. murale from the Balkans and R. bengalensis from Malaysia) have shown that the first process is very robust and transposable. For the second one, the way Ni is stored in the plant has a strong influence on extraction. A. murale transformation was explored in more details from the lab scale to the pilot scale. Results proved that Ni is totally transferred into the aqueous phase after 2 hours at 90 °C. A life cycle assessment has clearly shown the environmental interest of this approach (especially by detoxifying agricultural soils). INTRODUCTION Agromining is an emerging phytotechnology aiming at recovering metals thanks to hyperaccumulating plants (van der Ent et al., 2018). These plants are able to accumulate very high concentrations of metal in their aerial parts. For example, for nickel, the hyperaccumulation threshold is 0.1%, i.e. 10 grams of metal per kilogram of dry biomass. There are some advantages to use this technology instead of conventional mining techniques: •,Treating unconventional metal resources: they can be (i) natural soils with low concentrations but also low fertility because of the metal presence (like serpentine soils for Ni) (Bani et al., 2015), (ii) mine tailings or (iii) industrial wastes (like surface treatment sludge) after soil construction (Rue, 2017);"

Jan 1, 2018

By V. V. Morozov, Ganbaatar Zorigt, Delgerbat Lodoy, Y. P. Morozov

"At the processing plant Erdenet, a new facility for advanced ore diagnostics in-stream (at the conveyor), based on optical analyser of mineral composition, was tested. Such systems provide highly accurate in-stream measurements of ore properties. The system provided information on the ore mineralogical composition, the particle size distribution and the impregnation of minerals. A special flatbed facility for optical spectrum-based estimation of fine-crushed ore has been developed, being incorporated into the existing system of ore sampling and analysis. Application of the flatbed facility renders possible a high accuracy of determining ore mineralogical composition. High precision of the optical spectrum-based estimation is achieved using special devices, installed in the sampling and the sample analysis flow sheet, applied by the technical control department. Modern systems for optical spectrum-based estimation of ore grade provide a basis for effective automated control of ore benefication processes, based on the principle of advanced ore grade control. Process management task of grinding and flotation was to choose options that take into account the composition and grade of the ore coming. The calculation data array comprises consumption of reagents, ore processing, grind size etc. The systems implemented at the processing plant contributed to increasing copper and molybdenum recovery. INTRODUCTION In-stream ore grade analysis is a new trend in effective control of ore benefication processes. This is realised based on radiometric measurements in the X-ray and visible spectrum regions, in which mineral components of the initial ore (Sbárbaro and Villar, 2010) or the benefication products become apparent (Hyotyniemi and Ylinen, 1998; Haavisto and Hyötyniemi, 2010). An important advantage of such methods is in-stream measuring ore parameters, including mass fractions of individual minerals, which makes it possible to use the information obtained in the processes of automated control."

Jan 1, 2018