Search Documents

By William Skinner, Jonas Addai-Mensah, Keith Quast, David Robinson, Jason Connor

A review of the laboratory- and pilot plant-scale physical separation techniques for the beneficiation of nickel (Ni) laterites shows limited efficacy. To date, the only upgrade technique adopted commercially, prior to hydrometallurgical processing of Ni laterites, is the removal of a barren, coarse size fraction in the feed by classification. In the present work we investigated two low grade (~ 1%), goethite-rich Ni laterite ores’ upgrading by magnetic separation, attritioning/coarse, (lower Ni-grade) gangue rejection and flotation techniques. Low intensity (0.1T) dry magnetic separation at ambient temperature of raw samples and those pre-heated at temperatures up to 450 °C showed evidence of pay metal Co and Mn bearing asbolane and/or lithiophorite minerals pre-concentration in the magnetic fractions. Ni distribution, however, did not show any noticeable magnetic upgrade but followed the weight distribution. Other ore pre-treatment methods (e.g., desliming and sulphidisation) followed by froth flotation with anionic and cationic reagents also led to noticeable (~35%) Ni upgrade. This is due to the deportment of Ni across several gangue host mineral phases (i.e. Fe oxide/hydroxide and a range of silicate/aluminosilicate minerals). From chemical analysis, after disaggregation of ~ 1% Ni grade feed ore, coarse (-600 + 38 µm) and fine (-38 µm) fractions of ~0.6% and 1.3% Ni grades respectively, were also produced, suggesting that a significant upgrade in Ni content can be achieved by rejecting the + 38 µm fraction with the loss of <40% of the Ni. The ore mineralogy, particularly the complexity and high number of un-liberated Ni-bearing phases, greatly compromises physical separation methods for these ores, with the possible exception of screening after disaggregation of the fines inherent in the run of mine ores.

Jan 1, 2014

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012

By V. A. Luganov

The processing of pyrite concentrates may be accomplished with a preliminary enrichment due to withdrawal of iron sulfides from initial concentrate. The withdrawal of iron sulfides is possible with the help of magnetic separation when the magnetic iron sulfides (pyrrhotites) separate from non-magnetic fraction?the sulfides of non-ferrous metals. The conversion of non-magnetic pyrite to magnetic pyrrhotites of adjusted structure occurs because of roasting with the withdrawal a part of sulfur. The resultant pyrrhotites are strong ferromagnetic with hexagonal structure. This paper contains results of studying magnetic properties of pyrrhotites, findings of the de-composition of initial pyrite with the consequence homogenizing of product and hardening of product of decomposition in liquid nitrogen. Define the type of pyrrhotites super lattice structure, was established that at increasing of sulfur contention the magnetic properties of pyrrhotites are change ? pyrrhotite begin evince the properties of antiferromagnetic material and magnetic susceptibility of material is interruptive changing from 0 to 1.7×10-3~1.9×10-3 SI units/g system. The paper contains results of technological researching of pyrrhotizing-magnetizing roasting of pyrite concentrates in different condition: in unoxidizing, with the decreasing contention of oxygen and in autogenous regime in air atmosphere. Established that the magnetic susceptibility of products depend of pyrite degree dissociation and achieve 2×10-3~3×10-3 SI units/g system at 40%~45% desulphurization. Defined the conditions of steady regime autogenous roasting, at resultant products possess coefficient of magnetization, and this can be used magnetic separation for separating ferromagnetic pyrrhotites from gangues and non-magnetic sulfides of non-ferrous metals. This technology of pyrrhotizing roasting is recommended for effecting in industrial condition. The initial materials and products of roasting subjected to chemical, thermogravimetric, Moss-bauer spectroscopy and X-ray analysis, defined the magnetic properties.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By Hernán Menares, Diego Hernández

"Over the last few years, the copper mining industry has been facing a changing scenario with respect to both the market and society which has resulted in taking a closer look at the way in which mining is being done. The cycle of high metal commodity prices of the last decade left the industry with high costs. Together with increased environmental and social requirements, a decrease in ore body quality, scarcity of resources such as human capital, water and energy, has resulted in an ever-increasing challenge to make a profit out of new ore bodies but also to maintain the current operations in the longer term competitive. The major challenge is to create value for all stakeholders, exploiting ore bodies that nowadays are not considered economically attractive, which applies to both new ore bodies and existing operations, but in a sustainable way. In order to achieve this objective, it is necessary to approach the mining business differently in five main areas: (1) operational efficiency through better use of installed equipment and skilled labor force; (2) efficient use of energy; using opportunities for alternative energy sources and efficient design; (3) efficient use of water; diminishing losses and use of seawater as an alternative source; (4) minimizing environmental impact by eliminating effluents and controlling dust emission; and (5) a more closer, proactive and collaborative relationship with the communities allowing them to be an active player in the solution to assure a sustainable business in the long term. This presentation will show how Antofagasta Minerals is facing these challenges with a long term strategy that includes all of the above mentioned aspects and that is allowing the company to exploit its mineral properties in an efficient and successful way."

Jan 1, 2014

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

By R. Van Hille, A. E. Lewis

"The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pretreatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium.The pellet reactor was used to precipitate nickel as nickel hydroxy-carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed (See Figure 1).For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. In Figure 2, the global supersaturation ratio was relatively low, and thus there is little homogeneous nucleation and degree of fines formation. However, the fines occurring after the third sulphide input point (at 30cm from the bottom of the bed) indicate that local supersaturation also plays a critical role in fines formation. It was therefore concluded that, for the copper sulphide case, it is essential to control the supersaturation at the inlet points in order to prevent fines formation altogether, as it is not possible to agglomerate the fines once they exist in the bed."

Jan 1, 2003

By R. Van Hille, S. Lacour, A. E. Lewis, K. Peterson

"This paper compares thermodynamic modelling results with those obtained for copper sulphide removal from aqueous solution in both continuous and batch experiments at laboratory scale. Sulphide precipitation has been demonstrated to be an effective method for heavy metal removal. The advantages are the high degree of metal removal at low pH, low quantities of sludge formation, the ease of de-watering and low reactor retention time due to high reactivity of sulphides. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines, which are difficult to remove.Theoretical modelling was carried out using ASPEN Plus™ and OLI systems Inc ESP process. Both simulators were used to calculate copper sulphide recovery and residual aqueous copper concentrations as a function of pH. The predictions were then compared with experimental results. Both simulations predicted that all of the inlet copper would precipitate as sulphide CuS(s) over the entire range of pH and sulphide: copper molar ratios investigated. The simulation results were strongly influenced by the number of chemical species and the nature of the thermodynamic data taken into account in the model.The continuous experimental studies were carried out in a fluidised bed reactor (FBR). Copper sulphate was reacted with sodium sulphide and the solid precipitated directly onto the pellets in the FBR. The use of sulphide was motivated by high sulphate levels in local acid mine drainage and the ultimate integration of the metal removal process with a biological sulphate reducing process that produces an aqueous sulphide stream.A maximum dissolved copper removal of 99.6% (AAS analysis) and a total removal efficiency of 95.8% (dissolved copper minus fines) were achieved. Stoichiometry of the precipitate was determined from SEM/EDAX analysis (atomic percentages) and was close to 1/1, irrespective of the operating conditions."

Jan 1, 2003

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Fang Liu, Xin Tan, Zhong-ming Wang, Yan-bo Shang, Jie Zhao

"The flotation separation of sulphides bulk concentrate containing Cu, Zn, Mo and Bi, which was obtained by both table-flotation of gross sand of gravity separation of wolframite and bulk flotation of wolframite slimes using butyl xanthate and oil No. 2, etc., has been conducted by using the cyanide process in the tungsten concentrator. The process has problems of high reagents consumption (25 tonne of cyanide dosage per year) and mineral processing cost (800~1000 RMB reagents cost per tonne of by-product concentrates), high mutual containing loss in the by-product concentrates and serious environmental pollution caused by lots of cyanide-containing wastewater. In order to solve this problem, a new cyanide-free separation technology is studied, which is used to process this sulphides bulk concentrate with 8.68% Cu, 8.98% Zn, 0.26% Mo, 1.58% Bi and 40.12% S. The results of the closed circuit test show that Cu, Zn, Mo and Bi can effectively be separated from this sulphide minerals concentrate by using the reasonable flotation-gravity flowsheet, high-efficiency collectors and regulators simultaneously. The metallurgical recovery and concentrate grade are as follows: molybdenum recovery is 94.63% with 50.62% Mo content; copper recovery is 85.18% with 29.29% Cu content; zinc recovery is 75.92% with 46.49% Zn content; total Bi recovery is 65.08% with 16.86% Bi content. The new technology is an alternative to the cyanide process due to its low cost for reagents, satisfying separation results and economic profits, and solves the problem of environmental pollution caused by the use of large quantities of cyanide. Some important parameters in separating the Cu-Zn-Mo-Bi sulphides concentrate are also introduced in this paper. This study provides pretty good technical support for separating the polymetallic sulphide ores containing Cu, Zn, Mo and Bi by cyanide-free technique."

Jan 1, 2014