Search Documents

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci, A. Zucca

"Beneficiation of the epithermal gold mineralizations associated with an extensive alteration zone in the Serrenti-Furtei region on the island of Sardinia, is proving a complex issue. Experimental investigations have in fact demonstrated that while the ores contained in the upper parts of the deposit are amenable to conventional cyanidation, the gold contained in the refractory ores in the lower portions needs to be recovered by means of flotation, combined with leaching where necessary.The results of commercial heap leaching, carbon-in-leach (CIL) processing and flotation, designed on the basis of the experimental findings and applied to the oxidized portions and transition zones of the deep sulphide mineralizations, confirmed the expectations emerging from the laboratory tests."

Jan 1, 2003

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By D. Szyszka

During passing gas bubbles through mineral suspensions, some mechanical carryover of fine particles to the froth layer always takes place. The entrainment of mineral particles is influenced by many parameters, mostly by the particle size and the concentration of the frother. The paper deals with influence of selected frothers (methylisobutylcarbinol (MIBC), a-terpineol, and hexadecane tricosaethyleneglycol ether (C16E23)), common laboratory flotation frothers, on the mechanical car-ryover of quartz, a typical gangue mineral component of ores. Entrainment tests were carried out in a laboratory Mechanobr flotation machine with quartz particles suspended in aqueous frother solu-tions. The mechanical recovery of quartz in the presence frother was increasing with time and reached plateau after about 20 minutes of flotation. The plateau level of quartz recovery depended on the frother concentration. Initially an increase of the plateau with frother concentration was observed until the plateau reached the highest level called the maximum recovery emax. The emax can be used as a parameter to characterize the ability of frothers to entrainment. In the studied quartz-frother flotation system the maximum entrainment was 32%, 50% and 80% for methylisobu-tylcarbinol (MIBC), a-terpineol, and monohexadecane tricosaethylene glycol ether (C16E23), re-spectively. A comparison of the maximum entrainment factor emax with other, known from literature, indices such as bubble critical coalescence concentration (CCC), dynamic foamability index (DFI), Jw, e =25%revealed, except DFI, their similarity.

Jan 1, 2014

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By T. C. Alex

Mechanical activation of gibbsite [?-Al(OH)3] is the theme of this paper. Industrially prepared gibbsite used in the study has a mono modal size distribution with a median size, d50=110 µm. Mechanical activation of this gibbsite has been carried out in a planetary mill at ambient conditions. Mechanical activated gibbsite samples are characterised in terms of particulate characteristics, structural characteristics and reactivity. As a result, of milling, mono modal size distribution of the unmilled gibbsite changes to a broad multimodal distribution. Size reduction has been sharp in the initial stages of milling; median size reduces to ~7 µm during 15 min of milling. Thereafter no decrease in median size is observed; rather it is found to increase gradually with further increase in milling time, indicating particle aggregation. Morphological studies of milled gibbsite have shown that the platelets forming the agglomerate are separated first; the separated platelets then undergo breakage. Aggregation of particles sets in the later stages of milling as a result of increased surface area and surface energy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies have clearly revealed the changes in gibbsite structure during milling. Analyses of XRD data show that the crystallite size of gibbsite decreases as the milling time progresses whereas its microstrain is found to increase. Accumulation of energy in the structure is the result in both cases. TEM micrographs with signs of defects leading to disordering of gibbsite structure complement the XRD results. Reactivity of milled gibbsite, decrease in its deydroxylation temperature and increase in alkali dissolution, is found to increase with mechanical activation. Increased reactivity of milled gibbsite is found to have a strong correlation with the BET specific surface area. Keywords: mechanical activation, gibbsite, alkali dissolution, thermal dehydroxylation, reactivity

Sep 1, 2012

By R. Sakthivel

Blue dust is a high grade soft haematite material containing 96.14% Fe2O3 transformed into magnetite (Fe3O4), when it is subjected to planetary ball milling in the presence of iron powder as reducing reagent. X-ray diffraction (XRD), Field emission scanning electron microscope (FESEM) and Laser particle size analyser have been employed to characterize various samples collected at various milling times to know the phase evolution, particle size distribution and morphology of particles. X-ray diffraction studies reveal the formation of magnetite phase at the optimum milling time of 40 hours. Vibrating sample magnetometry (VSM) study demonstrates, that sample obtained at 40 hours of milling time exhibits saturation magnetisation of 14.757 emu/g whereas the starting material used in this study shows only 1.0425 emu/g. Keywords: Blue dust, reaction milling, magnetite, saturation magnetization

Sep 1, 2012

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Grigory Voyloshnikov, Sergey Petrov, Vladimir Petrov

"The treatment of high-grade copper gold-bearing ores is practiced extensively. However, due to low concentration of copper the application of a separate process for copper recovery can make this process uneconomical. The copper, in particular: in oxide minerals, intensively bounds with cyanide during conventional cyanidation. In this case, cyanide is not able to react with precious metals and the consumption of cyanide increases. The resulting copper cyanide complexes have a negative effect on the recovery of gold. Due to decreasing of the process parameters, a repeated use of the recycled solutions can be hindered, especially in the case of heap leaching. The technology of copper removal from the process solutions with simultaneous regeneration of free cyanide from copper-cyanide complex and producing of a saleable high-grade copper concentrate was developed. An important feature of this technology is simplicity, the absence of complex or dangerous operations and the use of common reagents. The choice of equipment depends on the ore treatment option: heap or vat leaching. Also, simpler equipment schemes are available. The studies, tests and industrial practice show that if the concentration of copper can be decreased down to the first numbers of mg per ppm or lower, it is reasonable to maintain the process copper grade in the recycled solutions at 30-50 mg/L. In this case, recycling of cyanide-bearing solutions is unlimited. The regeneration of free cyanide from that of bound with copper and other cyanide complexes is 95-98%. The grade of copper in the concentrate is 55-60%. This technology is an economically competitive option, in particular: with the account of the sales of copper concentrate. The removal of copper has a positive effect on gold recovery, especially during heap leaching. In addition to, this offers significant benefits in reduced costs."

Jan 1, 2014

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By M. Panayotova

Most of the quantity of the water soluble xanthates, used in mineral flotation, is consumed in the process. However, the residue amounts are water contaminants downstream the mineral processing operations and can be toxic to aquatic biota at concentrations of 1 mg/L. In order to be able to discharge water from tailing ponds to natural water bodies the concentration of xanthates has to be decreased. The present paper studies the uptake of potassium ethyl xanthate by directly modified with copper and lead ions natural zeolitic rock, without passing through zeolite transformation into homoionic form. Modified zeolite exhibits high, comparable with powdered activated carbon of chemical purity grade, capacity to remove potassium ethyl xanthate from model wastewater, with pH in the range of 7?9 and pollutant concentration in the range of 10-150 mg/L. The pollutant immobilization is fast. Both Cu and Pb modified zeolite behave as selective with respect to xanthate in the model wastewater, and Cu-modified zeolite possesses higher selectivity. The equilibrium is best described by the Freundlich equation. Keywords: xanthate, wastewater, modified zeolite

Sep 1, 2012

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003