Search Documents

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By Ramon V. V de Araújo, Roberto B. E Trindade, Pablo R. Fica-Piras

"Lead has been reported to affect blood vessels and kidneys. It also produces adverse effects in the mental and physical development of children and nervous system of adults. It is also considered as a possible cause of cancer. Because of all these threats to the human life, the reduction of its environmental occurrence, by means of recycling, is an important additional advantage to the usual ones derived of the procedures of the secondary metallurgy: lead can be recycled several times maintaining its characteristics equivalent to the primary one.Furthermore, this way of producing the metal avoids the environmental impacts of primary lead melting. Also, as an additional advantage, it triggers the metallurgical process with a raw material in what we observe higher lead content than in the natural ores. Some of the potential sources for these purposes are: ashes, slags, electrode residues, anodic muds, spent electrolytes, solid and liquid wastes, industrial or automotive catalysts, worn-out or obsolete equipment components and/or final consumption products.About 40% of world’s lead production comes from automotive batteries, mainly composed of four parts: plastic box, electrolyte (diluted sulphuric acid), contacts and connectors of Pd-Sb and plates (PbSO4, PbO2 and PbO). The plates represent 75% of the total mass. Metallic parts can be melted at moderate temperatures and then refined. The remaining fraction, constituted by the non-metallic portions, can be recovered by hydro and electro-metallurgical routes. These routes are preferred instead of pyrometallurgical ones due to the ultimate emissions of lead particulates and sulphur dioxide.The principal constituent of the residual paste of batteries is the lead sulphate. In this process, the paste is treated in two stages: in the first, lixiviating with Na2CO3 (desulphurization of the paste), obtaining PbCO3 and Na2SO4; in the second, the lead carbonate is lixiviated with HNO3, producing Pb(NO3)2, soluble, that can be converted to metallic lead by electrolysis. The reaction of PbSO4 with Na2CO3 in aqueous solutions is fast: the global rate is limited by the diffusion of the carbonate ions inside the reaction medium."

Jan 1, 2003

By Jia Muxin

The adsorption behaviors of metal ions on a silicate mineral and the flotability of a metalized silicate mineral with sodium oleate as collector are closely related to the structure of the silicate mineral. The adsorption isothermals of the metal ions on different silicate minerals are studied, the parameters of the isothermal give the information how many surface oxygen anions a metal ions is attached to, from this information and the structure of the mineral the site where a metal ion is attached can be guessed (The adsorption isothermals and adsorption behaviors with pH are fitted with Temkin, Frenudlich and Kurbatov equations respectively). Metal ions as Cu2+, Ni2+, Zn2+ are attached to the oxygen anions of surface species –Si-O– on the quartz surface, most of them coordinate to only one surface oxygen, their adsorption ability on quartz is low, but this metal ions on quartz surface protrude out of the surface perfectly, so their ability to combine with oleate acid radical is excellent. Quartz can be activated well by such metal ions. The isothermal of Fe3+ on quartz indicates these cations coordinates with more than two surface oxygen anions. This means the Fe3+ nucleates on quartz surface in the form of Fe(OH)3 colloid particles. The isothermals of Cu2+, Ni2+, Zn2+ Fe3+ on spodumene shows such ions coordinate with more than two surface oxygen anions, it indicate these ions may attach to the position where Li+ is formerly exists, such metal ions stay in a cave on the mineral surface, their adsorption abilities on spodumene are quite well, but they are affect by the oxygen anions of the two Si tetrahedron chains, the can almost not activate this mineral. These cations may attach on the site where Al3+ exists on the muscovite surface, just like spodumene, muscovite can not be activated well by such cations. Pt2+ has a large ion radius, as Pauling’s rules depicts polyhedron can not attach to Si tetrahedron well, the adsorption ability of Pt2+ on quartz is low and quartz is activated badly by Pt2+. On the other Pt2+ can adsorb well on spodumene and muscovite well and activated them well because it is not affected so bad by the tetrahedron oxygen anions of the minerals for their its large radius. The isothermal of Ca2+ on quartz indicates a Ca2+ coordinates with less than one surface oxygen anion, this means Ca2+ attaches on quartz mainly by physical adsorption. The adsorption abilities on mineral surface and the interaction abilities with oleate acid radical of the transition metal ions with the same valence are guessed to be determined by their d electron number, the rules should be d1<d2<d3<d4>d5<d6<d7<d8<d9>d10. Hydrogen bond may play an important rule in the activation of the mineral by HF and the interaction of the HF activated silicate mineral with collectors. The general rule is high bond valence and small metal ion radius surface species –Me-O can be activated well by HF with sodium oleate as collector. For example – SiIV-OH is neutral while –SiIV-FH+ and –SiVI-FH+0.33 are positively charged, the positively charged surface species are more likely to connect oleate acid radical via hydrogen bonds.

Jan 1, 2003

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

"A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change because of the strong path dependency of industry and infrastructure development. The metal production network is complex, as it consists of an interconnected and integrated system that incorporates multiple production routes for a spectrum of metals. More often than not, the production or recovery of a single metal is related to or dependent on the generation or recovery of another. The effects of these other metals is of great importance. In order to realize the potential economic importance of impurities, research and development have integrated the processes of copper production with those of lead and zinc, and connected the processes to those of among others silver, bismuth, tin and platinum group metals (PGMs), for example. The recovery of these elements from the interconnected circuits is extremely complex, as most of the elements must be circulated between two or more circuits before they are concentrated enough to make their extraction possible, and their recovery as a compound profitable.From such a system’s perspective, it can easily be seen that a complication for solid waste management has arisen through the development of products (consumer goods) that bring together metals that are not linked in natural resources. As a consequence, many of these materials are not compatible with any process in the metals production network that was developed for the processing of primary, natural resources, optimized for the processing not only of the primary metal but also for all mineralogically associated minor valuable and harmful elements. The formation of large or complex residue streams or undesired harmful emissions then inhibits processing and recovery of said products at their end-of-life. Another complication is that any change to the system (in metal production, SWM or product design) affects the system configuration. Due to the changing demands for metals as a result from the changing products made from the metals for example, the relationships between the processes in the interconnected metal production systems change. This affects both the demand for old scrap (required amount and grade) from waste management, and the environmental profile of the metals. Preferably, therefore, product designers, waste processors and metal producers must cooperate to realize optimal metal recovery in processing discarded consumer products."

Jan 1, 2003

By Graeme Lane, Yuqing Feng, Kaixi Jiang, Junwu Zhou, Zhengchang Shen, Tao Song

"Airlift reactors are used in a wide range of industries, such as hydrometallurgy, biochemical processes, chemical process industry and waste water treatment. With increasing superficial gas velocity three circulation regimes can be defined: no gas bubbles in the downcomer, gas bubbles remain stationary in the downcomer and gas bubbles in the circulating regime. In this paper a numerical modelling method was presented for gas-liquid flow in airlift reactors under different bubble recirculation regimes. Gas-liquid flow was modelled using the Eulerian two-fluid equations, and extra user defined subroutines were incorporated to consider the complex physics, such as bubble induced turbulence and turbulent dispersion force. Some alternative correlations of drag coefficient were used to capture the bubble distributions in the riser and downcomer of the airlift reactor, with consideration of the interaction between bubbles. As using constant bubble size is hard to describe global characteristics of the flow in airlift reactors for three circulation regimes, a model including multiple bubble sizes was presented to get more accurate simulation results of gas holdup and water velocity. Also, the inhomogeneous MUSIG model was used, as an exploration, to compute the complex flow regimes. The MUSIG model is a population balance method to predict the bubble sizes, taking break-up and coalescence into account. The modelling method was applied to a laboratory internal loop airlift reactor, and the simulation results were compared with the experimental measurements of Simcik et al. (2011) for gas holdup and water velocity. The three bubble circulation regimes were observed from simulation figures. Reasonable agreement was obtained over a range of operating conditions, and an improvement was demonstrated using the proposed methods."

Jan 1, 2014

By Reuter M. A., R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates. The copper powder characteristics, such as size and shape of particles, determine the tendency to adhere to reactor walls and to agglomerate. In order to make this process suitable for a commercial scale pipe reactor, process conditions and the reactor configuration were varied in order to influence the copper characteristics in a positive way. The aim was to achieve proper particle throughput in the pipe reactor and to obtain a well defined copper powder.In this paper the effect of both, chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By J. Broadhurst

"A number of metal supplying industries have in recent years seen the compilation of life cycle inventories (LCIs) and life cycle assessments (LCAs). The activity has largely been driven by the interest of ultimate metal users, such as the automotive industry, in the interest of designing more sustainable products. Often, the compilation of such inventories has been little more than an auditing exercise. However, the process of conducting an LCA can have more value, guiding designers and operators to points within the technology train where significant emissions and impacts originate. The LCA product can thus be used to inform on-site environmental management, and, where process data is used to construct dynamic operational models, to support strategic decision making in the realm of project planning and technology selection. LCA thus serves as a valuable tool to support the industry’s drive to support the sustainable development of the societies in which it operates.This paper reviews and compares the priorities of environmental and closure planning in the design phase, with environmental management and auditing during operation, and with green procurement of minerals and metals products. It shows how life cycle assessments of various complexities can be used to reconcile these various objectives, ensuring that the latter, critical to business success, can be addressed from the outset in a new project. The paper then reviews a case study of the use of LCA in the base & precious metals industry, where the complexity of the operation disallowed the simpler auditing process so that a detailed process understanding had to be built up in order to compile a meaningful life cycle inventory."

Jan 1, 2003

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. These results are significant considering the differences in ore type, proportion and type of iron sulfide minerals present, and grinding medium used in this study.

Jan 1, 2003

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Wieslaw Wszolek, Kazimierz Trybalski, Ryszard Tadeusiewicz

"The present work is an attempt of neural networks application to the description of complex technological processes of useful minerals enrichment. Neural networks are among the most convenient tools that have been added recently to the professional toolbox of modelling specialists, and they are particularly useful in realisation of multiple practical tasks, characterised by great complexity and relatively low amount of available a priori knowledge about the nature of the modelled processes. They are successfully applied in a wide variety of problems related to data processing and analysis, their prediction, classification or process control. The object of the study was the technological site for copper ore enrichment by floatation, being a part of technological line in the Ore Enrichment Plant ZG „Polkowice”, KGHM „Polska Miedz” S.A.The main floatation is described by parameters measured by the supervision and control system, which can be grouped with respect to the functions performed for the object:a) input function: aFG - copper contents in the feed material for the main floatation [% Cu]b) control: LFG I - level in the first section of the floatation unit [%], LFG II - level in the second section of the flotation unit [%], LFG III - level in the third section of the floatation unit [%], LFG IV - level in the fourth section of the floatation machine [%]. These quantities compose the five elements long input vector.c) output function: ? - copper contents in the waste from main flotation (final waste) [% Cu]The measurement data, containing the above-mentioned parameters, have been collected during the normal operation of the plant. The data contain momentary values of the parameters, registered every 10 minutes, covering the period of 196 hours of the plant’s operation (1176 measurements for each quantity).For construction of the model used in the study classical multi-layer perceptron-type neural network has been used, with one hidden neuron layer, trained by the error back propagation method."

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By Li Maolin, Cui Rui, Wang Guanghui

"As the stirrer speed directly affects the motion of grinding media, and hence the interactions with material particles to be ground, the rotation speed of a stirred mill is well recognized as one of the most important factors affecting the grinding performance. In this work, the effect of stirrer speed on grinding performance in terms of grinding rate and grinding energy efficiency was quantitatively investigated. Batch wet grinding tests of quartz powder at different stirrer speeds were performed, using a self-made horizontal stirred mill with alumina balls as grinding media. Grinding time, operating power and the sizes of ground product were recorded to analyse the grinding performance. The test results showed that grinding processes followed the first order grinding kinetics. The grinding rate constant increased with the increasing stirrer speed. Based on the grinding kinetics, the grinding energy equation was established. The energy utilization coefficient in the energy equation can be used as an indicator of energy efficiency. The energy efficiency decreased with the increasing stirrer speed. Quantitatively, with the stirrer tip speed increasing from 4.25m/s to 9.35m/s, the grinding rate constant was improved by 441.47%, whereas the energy utilization coefficient was decreased by 39.35%. The grinding rate constant and energy utilization coefficient can be used to evaluate the grinding performance when the grinding conditions need to be adjusted. The adjustment of grinding conditons would be optimal when grinding rate get significant improved with little decrease of energy efficiency."

Jan 1, 2014

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014

By Georg Unland, Thomas Wegner

"Impact crushers are widely used in different industries to crush materials which can vary from soft to hard and from ductile to brittle. However, the sizing of impact crushers is still based rather on empirical than on scientific approaches. Therefore, a test rotor was developed in order to investigate the principles of comminution by impact. Rocks of diabase with different diameters were used to gain the crushing properties with the following results:RESISTANCE AGAINST CRUSHINGLikelihood of BreakageThe likelihood of breakage is a function of the impact velocity and the particle diameter. The likelihood increases with higher velocities and larger diameters. Maximum Crushing ForceThe crushing force is related to the area of projection of the rock. The smaller the particles and the higher the velocities the larger are the maximum related contact forces.Contact TimeThe contact time increases with the rock diameter whereas the influence of the impact velocity is neglectable.Mass Specific Crushing WorkThe mass specific crushing work decreases with the particle diameter and increases with the impact velocity."

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By L. Tavares

The significant capital and operating expenditure of size reduction operations have maintained comminution on the spotlight of mineral processing research during the last century and, more recently, the concerns about the impact of these operations on the sustainability of the minerals industry, will remain to do so in the 21st century. One of the most popular approaches that have been used to deal with these challenges is the application of simulation both to reduce the uncertainty in the design and improve the operation of size reduction operations. From the initially purely empirical approaches, including the energy size reduction ?laws? and the phenomenological approaches, of which the traditional population balance model is, arguably, the best example, comminution modeling now reached a point in which more fundamental and mechanistic models are sought. The paper analyzes some of the advances that now make multiscale modeling of comminution processes realizable. On the microscale, greater understanding of the phenomena involved in fracture and fragmentation of single particles under different stressing conditions now exists. Particle breakage testing methods are currently used in a routine basis by industry and good quantitative descriptions of different breakage mechanisms are now available, although research is still required to develop appropriate models for a couple of them. On the macroscale phenomena, the discrete element method (DEM) has been successfully used not only to provide insights but also quantitative information on the transfer of mechanical energy from the machine to the grinding media in mills and to particles in crushers, while smoothed particle hydrodynamics (SPH) and computational fluid dynamics (CFD) to describe fluid flow. The paper also analyzes the importance of modeling mesoscale phenomena in size reduction, which is the interaction of particles forming assemblies or beds of particles, demonstrating some of the areas requiring further attention. Examples of application of the multiscale modeling approach to the inadvertent comminution of ore lumps during handling, to the comminution in vertical impact crushers and tumbling mills are demonstrated. Keywords: comminution modeling, DEM, SPH, CFD, multiscale modeling approach

Sep 1, 2012

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

By Victor Avdokhin, Valery Morozov, Valery Stolyarov

"The adaptation-determination method provides for keeping given relationship between concentrations of ionic and molecular components of a pulp liquid and correction of parameter of the model on the basis of analysis of ore composition, technological parameters of flotation, and cost of valuable components.• optimisation program “ADDEFLOT” and combined analyzer of pulp “RA-931”An adaptation-determination method provides for two-level control of bulk and selective flotation of polymetallic ores. The lower level provides for control of reagent dosing on the base of control of ionic composition parameters in the pulp liquid phase. The control goal is to keep the basis relationship among parameters of ionic composition (ions A, B, C) in pulp liquid phase given by equations of type:• alg[A] + blg[B] + clg[C] = K (1)Values of a,b,c coefficients are uniquely determined by a physico-chemical model used. Kind of the model depends on mineral composition of an ore and reagent regime applied. As parameter of ionic composition, also values of one or two parameters (or their combinations) can be used, for instance, pH, concentration of sulfide ions, ions of collector.The upper level of control is based on calculation and use of technological results of selective flotation. At the level, an adaptation of the model (1) is conducted. A principle of the adaptation is in determining (and including in pre-setting function of the lower level) such value of K parameter, at which maximal economic effectiveness of the process is reached. As a criterion of economic effectiveness of the process, a function of losses of several valuable components, taking into account cost of the metals lost, is used. For 2-component ore, in simplified form, the function is as follows:"

Jan 1, 2003