Search Documents

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"The effects of mixed collectors on some physicochemical parameters (thin film lifetime, kinetics of expansion of the three-phase contact, equilibrium three-phase contact angle and surface tension) involved in the elementary act of flotation were investigated experimentally.We have used the microscopic thin balance developed by Scheludko et al (1970) to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates at 1:1 molar ratio. The experiments were performed at a range of concentrations at pH 6.5. The equilibrium contact angle was measured with a microscope technique using the modified Mingins-Sheludko method (Mingins and Scheludko, 1979). The surface tension was measured by the method of Wilhelmy (Adamson, 1960). It was found that the mixed surfactants caused lower contact angles, lower rates of the thin film rupture and longer film lifetime, compared to the pure amine system."

Jan 1, 2003

By Claudio L. Schneider, Reiner Neumann

Any serious study of stereological conversion procedures must be based on an as accurate as possible complete fractionation of a real mineralogical texture. The original work on the Dolomite- Sphalerite Magstream? separation provided excellent data for establishing a working stereological conversion procedure, which has been successfully applied to a number of ores since its implementation. The linear grade distributions measured from these fractionated particles have been published and are accessible. The procedure for stereological conversion from areal measurements is exactly equal to the procedure for linear measurements. Particle composition from the dolomite-sphalerite density-fractionated particle sets, derived from both linear and areal data (Figures 1 and 2, respectively) are redundant, after proper transformation, and match the particle’s compositional range (plotted against S.G.) expected from Magstream?; direct density measurements by Hemicropicnometry plots within the ranges. Linear data cannot be used without conversion, but areal measurements are often directly applied as liberation spectra. Our areal measurements, without stereological conversion (Figure 3), differ completely from the results after transformation, and its density range falls mostly out of the expected/measured values. Therefore non-transformed areal data cannot be directly applied as useful liberation information.

Jan 1, 2003

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"OVERVIEWExpert Online is a software system that aims to mimic an informed expert on a minerals processing plant. The primary objective of Expert Online is to provide operators with effective training and on-the-job assistance. Training will mostly be done off-line (e.g. using simulators of the plant), while on-the-job assistance will help the operator during normal operation to run the plant in an effective manner. Although Expert Online focuses on the operator, it is expected to also be of value to other plant personnel, including supervisors and plant managers.Expert Online will make use of novel artificial intelligence technology (developed by MINTEK) known as the Interpreting Expert System (IES). Previously the IES was only able to explain the actions taken by the controller. Expert Online will extend this functionality to also take the process dynamics into account.Expert Online is being developed by a South African consortium comprising MINTEK (focusing on the research and development of the system as a whole), Lonmin (globally one of the biggest platinum producers, with plants suitable to test Expert Online on) and the University of Natal (academic partner, providing consultation and focusing on complex process modelling). The initial application of Expert Online will be on milling- and flotation plants.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By K. A. Natarajan

Involvement of various indigenous microorganisms in extracellular and intracellular iron oxide formation is a convincing index for iron ore biogenesis. Biomineralization of various iron oxides such as hematite, magnetite, goethite and limonite with the participation of aerobic and anaerobic microorganisms is well established. Various aerobic and anaerobic bacteria such as Gallionella, Leptothrix, Acidithiobacillus, Thermoplasmales, Pseudomonas, Bacillus spp and Shewanella putrefaciens, which are implicated in the formation of higher and lower oxides of iron have been isolated from different iron ore deposits. Diversity of microbial life in iron ore deposits can be put to beneficial use such as selective removal of undesirable constituents such as silica, alumina, clays, phosphorous and calcite and also to bring about environmental detoxification. Role of microorganisms such as Paenibacillus polymyxa, Bacillus subtilis, Yeasts and a sulfate reducing anaerobe in the biobeneficiation of hematite is illustrated. Surface chemical changes brought about by bacteria - iron ore mineral interactions are discussed with respect to hydrophobcity, adsorption isotherms, zeta potential data and bioreagents generation. Bacterial adaptation to minerals such as hematite, quartz, alumina, calcite, apatite and clays results in secretion of mineral ? specific biosurfactants such as proteins and polysaccharides. Such bioreagents can be used as selective collectors, dispersants and flocculants in iron ore beneficiation. Research results are highlighted to demonstrate silica, alumina, phosphate, calcite and clay removal from hematite. Environmental friendliness of such biobeneficiation processes is demonstrated with respect to biodegradation of toxic amine collectors, utility of ?in situ? organisms in enhancing settlement of fines in tailing dams and water harvesting. Keywords: bio-mineralization, bio-beneficiation, bio-remediation, Gallionella, Leptothrix

Sep 1, 2012

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Deventer

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated by using an ultrasonic probe in two slurry systems, i.e. cyanidation of a refractory sulphide ore and geopolymerisation of metakaolinite. The surfactant dithiophosphate was used to render the gold bearing sulphide particles hydrophobic, in an attempt to induce the formation of cavitation bubbles directly at the desired surfaces. Oxygen was injected into the cyanidation system to improve the attachment of oxygen bubbles to the hydrophobic sulphide surfaces. Geopolymerisation occurs in highly alkaline solution with waste aluminosilicate oxides and silicates as the reactants. The process of geopolymerisation is believed to involve dissolution of Al-Si oxides from solid particles, diffusion of dissolved Al-Si complex from the solid surface into the gel phase, condensation of gel phase and hardening of the gel phase. It has never been investigated how ultrasonication affects the above steps in synthesising geopolymers, despite a number of papers dealing with sonochemical synthesis of materials. The introduction of power ultrasound into such slurry systems is expected to result in advanced geopolymer materials.In the cyanidation of the pyrite concentrate, the kinetics of gold extraction were significantly enhanced in the presence of ultrasound, due to the prevention of passivation and the enhanced dissolution of sulphides. Cyanide consumption was significantly reduced with ultrasonication, owing to the oxidation of soluble sulphides to sulphate, minimising the cyanide consumption by sulphides. With oxygen injection, ultrasound significantly enhanced the leaching of gold from the pyrite concentrate, as oxygen could enhance the formation of the oxidation radicals by ultrasonic cavitation. In the presence of dithiophosphate, ultrasound further improved gold leaching in the oxygen-aerated system. Dithiophosphate could selectively adsorb at gold host sulphide surfaces, and make the surfaces hydrophobic. As a result, the ultrasonication effectiveness could be enhanced through forming cavitation bubbles directly at the interfaces."

Jan 1, 2003

By Kazimierz Trybalski

"Simulation methods have a big potential in the studies and analyses of complex technological processes and schemes. The simulation method used jointly with flow diagrams and related transmittance models allows describing and analysing dynamic characteristics.The paper presents results of simulation analysis of dynamic characteristics of ore dressing system, called closed circuit mill-classifier-mill. Such systems are widely used in ore processing plants. The system was analysed as a typical system with material feedback, to establish its dynamic characteristics.Flow diagram conforming to the technological scheme is presented in a figure. Transmittances shown in the scheme are defined as follows:GMP - transmittance of rod mill,GP, KZ, GW, KZ - transmittances of overflow and underflow streams of spiral classifier, respectively,GMK - transmittance of ball mill,GT - transmittance of underflow stream from classifier to ball mill,GU, MP, GU, MK - fraction transmittance of outflow streams of rod and ball mill, respectively, summed up at classifier input.Taking into account, in base of carried out analysis the transmittance forms of individual system elements. The calculations are based on numeral forms of transmittances of individual blocks, defined through industrial experimentation.Step input function to rod mill was assumed to be a step of mass ore flow rate to the mill. Responses are defined as product densities.This figure demonstrates the way of input signal transmission by consecutive elements of the system and shape of these elements' responses. It can be noticed that step signal undergoes gradual change from the stream of the first order to those of higher and higher orders as a distance from process leading edge increases. Simultaneously, the impulse signal is subject to systematic smoothing and decay. From the technological point of view, the most important is response stream in point 5 (on the above figure) that characterises classifier overflow, which is a final product of this system."

Jan 1, 2003

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By Francis Pitard

"The optimization of metallurgical processes requires an in-depth understanding of the heterogeneity carried by any constituent of interest. It emphasizes that knowledge of the Theory of Sampling (TOS) is the necessary step to ensure that valuable and valid research programs, pilot plants, feasibility studies, plant design and plant operations have been set on solid foundations. Too many publications today are solely based on the properties of the sample, with no mention of how this sample relates to anything in the environment where it was collected. Unfortunately sampling is an error-generating process that leaves no apparent tracks of its shortcomings. Indeed, it is easier to track down analytical errors than sampling errors. Consequently, bad sampling practices plague the scientific community and the industry and are responsible for severe money losses, unsatisfactory science and processing, and sometimes litigation. A point-by-point strategy is presented addressing sampling problems in early stages of a project. Sampling system requirements for metallurgical accounting and process control are listed. The use of Chronostatistics is suggested to determine if sampling systems are performing satisfactorily and to identify the various types of process variability that may not be easily detected by a conventional inspection of available chronological data. This strategy will help engineering firms, manufacturers, managers and supervisors to provide, install, use and maintain key sampling systems located at very important points in a process. Equipped with the appropriate sampling and statistical tools it becomes easier to minimize reconciliation problems with the mine, with suppliers and with clients. Contrary to the beliefs of many people, good sampling systems are not expensive because in the long run they help to reduce hidden cost and better regulate plant productivity; they most certainly minimize the number of unnecessary meetings looking for solutions where there are none. The suggested strategy will help specialists to extract maximum information from the available data, as large investments and crucial decisions depend on it."

Jan 1, 2014

By Felix M. Zhuravlev, Vitalij P. Lyalyuk

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By Jussi Liipo, Pertti Lamberg

Image analysis of process samples gives precise data on particles and their composition. The results presented as liberation tables and maximum grade-recovery curves are informative and good for comparing different feed materials, but basing on them it is impossible to predict the results of the mineral separation process (flotation, magnetic separation, gravity separation) in details. The exact and extensive particle data has remained large unused, because there has not been a model nor a modeling program to include particle information in mineral separation processes. This study introduces a method, which incorporates the particle data in the kinetic model of flotation. Similar approach can be used in modeling other separation processes, too.

Jan 1, 2003

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the gold desorption process. The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide. Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC.

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By J. Gebhardt, D. McBride, M. Cross, S. Gilbert

Heap leaching of ores containing chalcopyrite offers a low cost option to treat low grade complex copper sulfide ore bodies. However, the slow leach kinetics of chalcopyrite at ambient conditions typically results in unacceptably low recoveries. As the mineralogy of new ore deposits becomes more complex and the effects of gangue chemistry exert a greater influence on copper sulfide leach behavior, the control of leach reaction chemistry becomes more critical. Computational fluid dynamics (CFD) technology has been useful in the capture of multi-phase interactions and provides a path to simulate complex fluid flow, gas and liquid phases, through the heap, along with species transport. Coupling the flow models with the reactive mineral dissolution, and the sometimes competing aqueous chemical and solid-liquid reactions, yields a comprehensive model of the heap leach process. The leach kinetics of chalcopyrite dissolution in heap conditions is examined, and the incorporation of chalcopyrite leach kinetics in the CFD model is described. The application of the model to investigate optimization of the heap is discussed.

Jan 1, 2014