Search Documents

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018

By A. Usov

The studies carried out by the Russian researchers and those carried out jointly within some contracts with scientific organizations and companies of other countries, show that the electric pulse disintegration of materials (ED), proposed and investigated in detail in Russia (Kalyatsky, et al, 1980; Usov et al, 1987; Semkin et al, 1995; Usov and Tsukerman, 2000; Kurets et al, 2002) has been widely recognized and developed abroad (Andres, 1995; Inoue et al, 2000; Biela et al, 2008). The Russian and international journals and the proceedings of the conferences dealing with the electric pulse disintegration pay great attention to the principal principals of selective disintegration of materials. There is no, however, any information concerning both the technical means developed to implement the technique and the assessment of their performance, which would be necessary in objective assessment of the industrial use of the technology. The results of long-term studies of the technique and technologies of electric pulse disaggregation by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute "Mekhanobr"(S.Pertersburg) described. Exploratory stands and technological installations are developed to carry out pilot tests and operations under production conditions. Basic circuits and classification of technical means electric pulse disintegration of the materials are proposed, the analysis of transportation schemes and classification of the material in the disintegration apparatus are given, construction of chambers for continuous stadial disintegration of ores and materials are presented. The features and technological efficiency of electric pulse disintegration of various types of ores, and the spheres of effective use of the method have been determined. Keywords: electropulse disintegration, disintegration machines, chambers of comminution, stadial comminution.

Sep 1, 2012

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By X. J. Lu

Purified Na-montmorillonite samples were used as the starting materials to prepare organically modified montmorillonites (OM), and a series of OM samples were prepared by intercalation of al-kyl quaternary ammoniums with different alkyl chain length. The interlayer spacing (d001) of the OM was determined by small angle X-ray diffraction and its gelating performance was characterized by measuring the viscosity of OM/dimethylbenzene mixture. The effects of alkyl chain length, dosage of alkyl ammonium, intercalation duration and layer charge of the starting material on the OM structure and gelating properties were investigated. According to the results, the adsorption quantity of the alkyl ammonium is dependent on the hydrocarbon chain length, the dosage of the alkyl ammonium and the retention time. The adsorption quantity of the alkyl ammonium increases with the chain length and the dosage, and extra adsorption more than the CEC of the montmorillonite sample was observed under the dosages of more than 1.3 CEC. The interlayer spacing (d001) of the OM shows a dynamic variation with the dosage and the retention time, and super interlayer spacings greater than the length of the alkyl ammonium were observed under larger dosages and shorter retention times. However, the gelating performance of OM does not follow the variations of the adsorption quantity of alkyl ammonium, an optimum viscosity value of OM/ dimethylbenzene gel was observed with the moderate adsorption of the alkyl ammoniums. Furthermore, the layer charge plays an important role on the gelating performance of OM. The OM synthesized by the starting material with lower layer charge shows better gelating performance in the dimethylbenzene solution.

Jan 1, 2014

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By A. Pirson, J. Souza, A. Araujo, M. Barbosa, F. Guimarães, J. Lima

"Although a large number of processes have been developed and applied to the separation of barite from other minerals, there is a lack of information in the literature about the separation of barite from iron ores. Nowadays, there are millions of tonnes of iron ore disposed as a waste or tailings given its high content of sulphur in the form of barite. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and check if a marketable by-product can be produced by drawing upon rich barite tailings. INTRODUCTION The exploration of iron ore containing barite results in a large amount of unrecovered material. The main difficulty in processing and using barite bearing iron ores is given by their high content of sulphur, silica and barium, which are unwanted chemical compounds in the subsequent processes in iron industry. As a result, millions of tonnes of iron ore are discarded every year into tailings or as a waste, which results in production losses, higher operation costs and environmental impacts (Praes et al. 2013). Therefore, the separation of barite from iron ores not only means reducing the environmental impact, but also an opportunity to generate income and beneficiate society. The beneficiation of barite bearing iron ores is a subject which requires a deeper investigation to solve the challenges faced by the iron industry. There are only a few studies that describe flowsheets proposed for the production of barite concentrate of iron ores. The most likely reason for this gap is that barite is frequently exploited commercially as a primary product rather than a by-product. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and verify if a marketable by-product can be produced by drawing upon rich barite tailings."

Jan 1, 2018

By C. L. Xiao

With reference to the test report carried out by Guangzhou Nonferrous Metal Research Institute in 1983, the mineral process flow sheet of Yichun Tantalum-niobium mine is determined based on the characters of ores and successful experiences in light of the problems in the existing flowsheet: The ore is desilted before crushing; the primary slime is separately treated; the staged grinding process used while the fine slime is collectedly treated with tantalum and niobium as the main recoveries and lepidolite and feldspar powder as the secondary. The flowsheet is featured by comprehensive recovery, low investment and low energy cost.

Jan 1, 2014

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

At times the phosphate industry, in Florida, encounters phosphate rock that gives lower than expected P2O5 recovery in the rougher plant section. The drop in recovery is typically 10% and as much as 30% or more. Variations in feed quality from day to day, shift to shift and even from drag-line to drag line, represent a challenge to the beneficiation plant operators and reagents? suppliers. Therefore, this characterization study has been initiated to identify the reasons for the differences in flotation behavior of such feeds. The study involves many samples to cover such variations. The characterization work includes: ? Mineralogical and chemical analysis; ? Size, shape, surface roughness and porosity analysis; ? Surface charge and surface contamination with other phases (minerals); ? Clay content and its relationship to phosphate and silica particles. The results correlated with flotation data and adsorption density measurements clearly establish the statistically significant variability in characteristic features that influence flotation response. This article discusses results from the above listed studies. On the basis of the obtained data, recommendations of practical approaches to overcome the problem of feed variability in phosphate flotation plants are delineated.

Jan 1, 2014

By Jihoe Kwon, Daeyang Lee, Mario Fujimura-Kashiwagui, Heechan Cho

"Calcium carbonate is one of the most widely used mineral in today's industries such as plastic, paper and pigment. There are many essential physicochemical properties required by each industry field but the most common requisite is size. One way to achieve appropriate size is grinding. Grinding is typically an energy intensive process, consuming about 40% of total energy cost in mineral process. Due to that reason, optimization of grinding process is a critical element to achieve price competitiveness. Two different type of grinding apparatus were hired to find out optimum condition in terms of energy efficiency. Utilizing samples containing 10, 20, 30 and 40% solids concentrations, a 1l batch type attrition mill was operated as the first grinding step at various operating speed with 1? to 5? grinding media in order to study the optimum operating conditions to reach submicron particles. Next, a 0.15l vertical beads mill was tested as next step with 100? to 500? grinding media to study the optimum conditions in the submicron range. Net energy and the specific energy input was measured to reach stated size ranges. Also, using a back-calculation based on the population balance model further operating conditions were studied. There were several competitive combinations which showed significant energy efficiency improvement when compared with the single step grinding."

Jan 1, 2014

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By Jorge Rubio, Gabriel Berkowitz, Fabiano Capponim, Carlos Perez Guerrero, Elves Matiolo, Denise G. Nunes

This paper describes some advances in flotation research in fines (“F” 38 to 13 µm) and ultrafines (“UF” < 13 µm) mineral recovery by two different techniques, at laboratory scale. Extender flotation and flotation with .multi-bubbles. (bubbles with a wide size distribution) of copper sulphide fines (ore feed of about 1 % Cu) were compared with a .standardised. mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), .true. (bubbles-particles attachment only) flotation recoveries and process kinetics. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physico-chemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged.

Jan 1, 2003

By Z. F. Dai

The Thompson Nickel Belt, located in Northern Manitoba, Canada, contains more than 400 million tonnes of ultramafic low-grade nickel mineralization in 9 deposits. One of these, the Pipe deposit, was mined between 1971 and 1983 producing a Ni concentrate of 9% to 11% grade at 73% recovery. The operation was terminated because the poor recovery, low Ni grade and high MgO con-tent of the concentrate made processing this ore uneconomical at the metal prices prevailing at that time. Vale Inco is now re-evaluating these deposits with the intent of providing a new source of concentrate for its Thompson integrated processing facility. It is known that serpentine slimes coating on the sulphide surfaces are responsible for the poor metallurgy. Various desliming methods were tested including settling, elutriating, tabling and hydrocycloning. Hydrocycloning has proven to be the most effective means of desliming. With a feed assaying 0.70% Ni and 33% MgO, a rougher flotation concentrate assaying 22.7% Ni and 4.8% MgO was produced at a Ni recovery of 62.5% (relative to the feed to grinding), with no utilization of slimes dispersants. Another 16.6% Ni recovery was achieved in scavenger flotation resulting in a total Ni recovery of 79.1%. Batch flotation tests using various flowsheet configurations to optimize the grinding, desliming, reagentizing and flotation conditions are in progress.

Jan 1, 2014

By J. J. Liu

In the Bayer process, control of alumina trihydrate particle size, oxalate stability and morphology and foaming is crucial for improving the yield and quality of alumina trihydrate. One way to economically achieve such control is to employ specifically developed chemical additives, termed, crystal growth modifiers (CGM?s). In this paper, the mechanism of action and practical application of CGM?s in the Bayer process are summarized. The application of CGM additives allows for both enhanced agglomeration and secondary nucleation control, and hence coarsening of the particles. Current research efforts have utilized the information gained from mechanistic studies to enhance the performance of CGM products. It was demonstrated in both laboratory tests and industrial operations that the newly developed CGM formulations have a range of properties with enhanced performance, compared to the current commercial products.

Jan 1, 2014

By Y. J. Ferdosi

This paper presents the outcomes of the preliminary investigation focused on the potential usage of Electrochemical Impedance Spectroscopy (EIS) in minerals processing. Currently, Electrochemical Impedance Spectroscopy has been successfully employed in the characterization of multilayer structures formed as molecules adsorb on flat surfaces and is commonly used in bio-related research. Few studies have explored the application of EIS in minerals processing, particularly for mineral particles and flotation systems. In the first series of tests, the impedance response was investigated as a function of particle size, shape and hydrophobicity using model quartz particles. The particle size fractions and the shape were found to contribute to the impedance response. The more hydrophobic quartz particles resulted in a higher impedance values. Further tests involved pure sulfide minerals including chalcocite, bornite, chalcopyrite and pyrite. The AC impedance measurements were conducted as a function of collector (sodium ethyl xanthate) dosage. The AC Impedance data was modeled using the combination of reference circuits. It has been shown that adsorption of collector onto sulfide minerals surfaces results in a higher magnitude of impedance. Increasing the collector dosage resulted in an increase in AC impedance for chalcopyrite, while a decrease was observed for chalcocite. Significant variations in impedance were exhibited by bornite and pyrite with a gradual increase in collector dosage.

Sep 1, 2012

By Kari Niiranen, Patrick Krolop, Viktoria Töyrä

Luossavaara-Kiirunavaara AB (LKAB) operates an iron ore mine, three beneficiation plants and three pelletizing plants in Kiruna, Sweden. The current methods of separation in the beneficiation plants are wet low intensity magnetic separation (WLIMS) and reverse apatite flotation, where the WLIMS stage is regarded as the crucial part of silica separation from the ore. Currently, the high-grade iron ore deposit of Kiirunavaara has a low grade of silica in situ, of approximately 3.0% SiO2, but the silica grade is expected to increase in the deeper parts of the deposit with a complex silicate mineralogy. An increasing silica grade will affect especially the production of direct reduction pellets (LKAB DR Oxide Pellets), one of the main products of LKAB in Kiruna with an average silica grade of under 0.75% SiO2. The silica grade in the magnetite concentrate is normally limited to a maximum level of 0.55% SiO2 in order to achieve the required chemical composition in the pelletizing process. In order to study the possibility to reduce silicate content in the magnetite concentrate (pellet feed) in the beneficiation plants in Kiruna obtained by wet low intensity magnetic separation (WLIMS), enlarged mineral processing test work was carried out in the LKAB’s mineral processing laboratories in 2016. The test work consisted of comminution, low intensity magnetic separation and reverse cationic silicate flotation at laboratory scale, complemented by screen analysis, chemical assays and mineralogical investigation. The results of these mineral processing test work showed that the magnetic separation is not sufficient to reduce the silica content in the magnetite concentrate, particularly in the case of the high-SiO2 ore type B2-a. The reverse cationic flotation can be regarded as a possible solution to reduce the silicate content in the magnetite concentrate obtained by WLIMS and to achieve the required silica grade of less than 0.55 % SiO2 in the pellet feed. The results of this study provide a good basis to understand the behaviour of different silicates in the existing beneficiation process. Furthermore, it serves valuable information for development of new beneficiation processes and for investment in new equipment at the beneficiation plants in Kiruna in the future.

Jan 1, 2018

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

By Renato Oliveira, Walter Valery, Alex Jankovic, Birol Sönmez

"The ball mill is the most common ore grinding technology today, and probably more than 50% of the total world energy consumption for ore grinding is consumed in ball mills. On the other hand, high pressure grinding roll (HPGR) technology is relatively new to the mining industry, with significant application only since the beginning of the 21st century. Both ball mills and HPGRs are typically used in closed circuit with classifiers. There is a general consensus within the industry that classification efficiency and circulating load both have a major effect on the efficiency of closed circuit ball mills. Metso Process Technology & Innovation (PTI) conducted a laboratory test program to understand the relationship between classification efficiency and circulating load, and the impact on the performance and capacity of ball mill circuits. However, the effects on HPGR performance are significantly different. Metso PTI has initiated a pilot scale test program to evaluate the size reduction performance of the HPGR under different circuit configurations. A series of pilot scale HPGR locked cycle tests were performed to simulate the following circuit configurations: including closed circuit with a screen, partial product recycle and edge recycle. This paper discusses the results from the pilot scale HPGR and laboratory scale ball mill test programs. The effect of circulating load and classification efficiency on the performance of ball mill circuits is compared to the effect on HPGR circuits. The fundamentals of grinding behavior are also discussed in order to explain the difference."

Jan 1, 2014

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018