Search Documents

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By M. N. Chandraprabha

Arsenopyrite is often associated with sulphides like pyrite, chalcopyrite and galena in refrac-tory gold ores. Selective flotation of arsenopyrite from associated sulphides is desirable for effective gold extraction when the gold is preferentially associated with the arsenopyrite matrix. By contrast, presence of arsenopyrite in flotation tailings poses a serious environmental threat due to arsenic dissolution. To prevent arsenic contamination from the mine wastes, it would be more economical and environmentally beneficial to remove this mineral during the froth flotation step. Use of Acidithiobacillus thiooxidans in the detoxification of arsenic containing sulphides is outlined in this pa-per. Biomodulation using Acidithiobacillus thiooxidans resulted in the preferential depression of pyrite from arsenopyrite. By suitable conditioning with cells and collector effective separation of arsenopyrite from pyrite was achieved. Biomodulation with wild cells did not yield separation of arsenopyrite from chalcopyrite. However, bacterial affinity could be induced to a desired sulfide mineral through environmentally controlled adaptation techniques. Through the use of arsenic-adapted bacterial cells, selective removal of arsenopyrite from chalcopyrite was readily achieved.

Jan 1, 2014

By Vladimir F. Skorokhodov, Nikolay N. Melnikov, Svetlana P. Mesyats

"Among the problems of the civilization development, a problem of interaction between man and natural environment can be highlighted. In the twentieth century the human transforming activity had got scales of geological processes and defined the contradiction between the goal to increase the quality of human life and possibilities of the natural environment. Last twenty-five years after the World Summit on the Environment (1992) indicate that the development of civilization is still based on receiving super profits from the natural resources exploitation. This statement is confirmed by economy globalization rates, growing contradictions between consumption and production, depletion and degradation natural environment. A new technological order is formed at the time of growing world population, technological capacities, organizational complexity, from one side, and global scales of geo-resources consumption, on the other side. Sciences, determining the further civilization development, should take on the task to change the social worldview, since the preservation of human population consists in remediating and maintenance of biosphere functions as a regulator of ecological balance. The new worldview in the geo-resources exploitation is based on the Ecological strategy of mining development, which consists in reducing mining-induced loading on natural environment while increasing efficient mineral production and processing, and providing for a comprehensive solution of tasks on mineral deposit development. One of strategic trend of mining development is to increase complexity and completeness of useful component extraction from ore and mining deposits while reducing wastes and decreasing their stockpiled volumes. The implementation of the ecological strategy has shown that the future is determined by reduction of the environmental impact while improving the efficiency of mineral mining and processing.INTRODUCTION The global nature of environmental problems caused by the scale of consumption of natural resources, huge amounts of waste, and intensive man-made impact on the environment requires a revision of the strategy for the natural resources development. Many existing technologies are ineffective in achieving the ultimate goal. Direct output in the raw materials - the end product technological chain rarely exceeds 10%, which implies a huge amount of work to move the soil. In addition, the feature of scientific and technological progress at the present stage is the growth of power-to-weight ratio."

Jan 1, 2018

High flotation of iron sulfide minerals at high pH values in copper ores is mainly due to the activation of these minerals by copper species dissolved from copper sulfide minerals during grinding. Several methods have been tested to reduce this copper activation during grinding and therefore to depress iron sulfide flotation. They include grinding the minerals at high pH values or with a less reactive medium such as high chrome, and addition of a thiol collector or copper complexant during grinding. The efficacy of these methods in the flotation of a copper ore was tested against more common methods of depression of iron sulfide flotation. The mechanism of iron sulfide depression in these methods was also investigated.

Jan 1, 2014

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By J. C. Wilmot

The chemistry of aqueous cyanide containing species in the presence of reduced sulfur sources was investigated. Reactions were studied as a function of time and tracked using novel analytical techniques developed for the analysis of the species of interest in the sample matrix. Species of interest in this work were ?free? cyanide, thiocyanate, cyanate, metallo-complexed cyanide, and various sulfur and sulfur-oxygen species. The studies were conducted under constant temperature conditions at pH values above 10.5 and in the absence of light in order to eliminate photochemically induced cyanide reaction effects. The reaction products of cyanide when in contact with pure sulfur, pyrite, pyrrhotite, sphalerite, and cinnabar are reported. These data combined with data for cop-per, arsenic and lead sulfides, which have been previously published, are used to predict the fate of cyanides in refractory gold ores containing sulfides. A mass balance on the cyanide reaction products was completed for all experiments. From these studies insight into the chemical relationships of cyanide, the specific metal sulfide, thiocyanate and cyanate have been gained. When looking at the results of the experiments, it was immediately apparent that even though the overall conversions of cyanide to thiocyanate were different, most of the samples exhibited a similar pattern of reactions. The recovery of cyanide in these experiments was better than we expected, averaging in most experiments to be over 90 percent. Based on this research, the formation of cyanate was probably the main route of loss. The pathway choice for the various minerals was also elucidated in these experiments. The competitive oxidation pathways that cyanide can take have been tracked for sufficient time to determine the ?final? fate of cyanide in a process. Initially, it was thought that the cyanate may be involved in a hydrolysis reaction to form ammo-nia and carbonate ion, but upon further inspection of the data, there was not the drop-off in total cyanide recovery that would manifest itself were this to happen. On the other hand, the hydrolysis of thiocyanate to cyanate and sulfate would require oxidizing conditions which did not exist in solution at the beginning of the experiment. If the solutions were to be sufficiently oxidizing in nature for this to happen, the initial amount of cyanide would have been converted to cyanate quickly. The data support premise that the ?hydrolysis? of thiocyanate to cyanate and sulfate occurs to some extent in the experiments conducted. Knowledge gained from the experiments with pure metal sulfides helped interpret the results of experiments with refractory ores found in the State of Nevada.

Jan 1, 2014

By Cheng Xiang, Nan Ye, Xinyuan Ke, Yang. Jiakuan, Huabin Wang

Bayer red mud is a highly alkaline residue produced by the alumina industry through the Bayer process. Its disposal is a worldwide problem. The high alkali content and poor pozzolanic activity is aconstraint for its utilization on construction materials. In this study, the red mud was activated through an alkali-thermal method to improve its activity so that it can be utilized in geopolymerization. The red mud was mixed with different amounts of sodium hydroxide, and calcined under 800 °C to produce geopolymer precursors, and then mixed with water directly to prepare one-part geopolymer. X-ray diffraction was conducted to study the phase transformation of red mud and the mechanism of its geopolymerization. Nitrogen Isothermal Adsorption tests were conducted to analyze the pore structure of the geopolymer binders. The results show that calcinations with alkali would promote the Al in red mud transforming into glassy SiO2 to form the N-A-S phase which is soluble in water. When the red mud was calcined at 800 °C with a Na2O addition more than 10%, the dissolving of Si and Al from red mud was greatly improved. The thermal-alkali activated red mud with 10% Na2O obtaining a compressive strength of 9.77 MPa after it reacted with water and cured for 7 days at 20 °C and 95% RH. But the strength decreased as the curing time extended to 28 days. The reason is suggested to be that the polymerization of Al-O and Si-O is unstable due to the low Si/Al ratio of red mud. The alkali in the structure dissolves again into the pore water and corrupts the pore structure. Therefore, the thermal-alkali red mud should be combined with other reactive aluminosilicate materials such as granulated blast furnace slag to absorb the alkali released by the thermal-alkali red mud at the latter curing days.

Jan 1, 2014

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By K. Malysa

Bubble collisions with ore grains and a selective formation of the bubble-grain aggregates are necessary steps for flotation separation of useful and gangue components of an ore. For the attachment of valuable mineral grain to the colliding bubble a liquid film, separating the bubble and the grain needs to rupture during short time of their collision. High hydrophobicity of the grain surface is favorable because stability of the separating (wetting) film is much lower at such surfaces, that is, the film ruptures faster and at greater thickness. Simultaneously, it needs to be kept in mind and taken into consideration that high affinity to air is a typical feature of hydrophobic surfaces. Thus, when the hydrophobic surface is immersed into aqueous phase the air can stay attached to such surfaces and affect kinetics of the bubble attachment. The paper presents results and analysis of dynamic phenomena occurring upon the collision of the rising bubble followed by its attachment to hydrophobic (Teflon) plates of different roughness. The influence of the Teflon surface roughness, solution concentration, bubble size and impact velocity on bouncing of the colliding bubble, time of the three phase contact (TPC) formation and drainage time of the liquid film, formed between the solid and bubble surfaces, is described. High hydrophobicity, as showed earlier (Malysa et al, 2005), does not assure that each collision leads to the TPC formation and attachment of the colliding bubble. Roughness is the parameter of crucial importance for kinetics of the bubble attachment to hydrophobic surfaces (Krasowska and Malysa, 2007; Krasowska et al, 2009; Kosior et al, 2011). Enlarged roughness of the Teflon plate, from ca. 1 to 80µm, results in shortening the time of the TPC formation (bubble attachment) by over an order of magnitude - from 105 to a few milliseconds only. Higher surface roughness means that larger amount of air can be entrapped in bigger scratches and cavities of the Teflon plate during its immersion into aqueous phase. Results documenting importance of the air presence are showed and mechanism of the air facilitated TPC formation and bubble attachment to hydrophobic surfaces is described. Keywords: bubble collisions, hydrophobic surfaces, teflon plate roughness, TPC formation

Sep 1, 2012

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

By Y. F. Guo

Laboratory scale experiments were conducted to produce titanium-rich material from Panzhihua ilmenite. The results showed preoxidation with sodium salt additive especially for Na2B4O7 signif- icantly advance the reduction of iron in Panzhihua ilmenite. Acceleration mechanism of preoxidation with Na2B4O7 has been studied here. The maximum metallization of iron 92% can be obtained under conditions of preoxidation at 850? for 30 min and subsequent reduction at 1100? for 150 min. The rusting separation technique to reduced ilmenite has been further studied, obtaining titanium-rich product with TiO2 over 82% and the recovery of TiO2 above 97%.

Jan 1, 2014

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

The status of utilization of copper ore resources, and the application and development of biohydrometallury technology in the world is reviewed. Based on the characterization of Zambia?s copper resources, biohydrometallurgy technology is shown to be a practical approach to extract and utilize the enormous low grade copper resource, such as ore tailings and low grade copper ore in this country. Through the cooperation of CSU, China and MMMD, Zambia, ?CNMC-CSU Demonstration Base of Biohydrometallurgy Technology in Zambia? was launched and several biohydrometallurgy plants are being constructed. This indicates that the biohdyrometallurgy technology would be applied soon in Zambia and in the whole Africa. Biohydrometallurgy technology stands as an efficient alternative to the traditional pyrometallurgy process and it can be the key to unlock mineral resources value. Keywords: biohydrometallurgy, low grade copper ore, Zambia, Central South University

Sep 1, 2012

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018