Search Documents

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By G. H. Li

Preparation strontium carbonate with celestite concentrate by flotation is studied by agglomeration-reduction roasting process. It is shown that, the drop strength of green pellet is greater than 4 times?(0.5m) -1 under the balling conditions of moisture of 9% and time of 18~20min. Lignin xanthate obviously improves the ballability of the celestite concentrate due to the increase of surface hydrophilicity, therefore, the balling rate is increased, as well as green ball strength. The drop strength of 7 times?(0.5m) -1 can be obtained when the lignin xanthate dosage is 0.5%~1%. Reduction roasting with anthracite shows that the SrSO4 conversion is 82%~83% for celestite concentrate pellet, under the optimal conditions of roasting temperature of 1100~1150? and time of 30min, and it is 10% higher than conversion of celestite lump under the same conditions. The strontium carbonate are prepared after roasted pellets are leached, purified and carbonated, and the SrCO3 content is higher than 97% , while the content of CaCO3 is less than 0.3%.

Jan 1, 2014

By Bianca Foggiatto, Marcos Bueno, Rajiv Chandramohan, Eddie McLean, Greg Lane

"With the increasing depletion of high-grade ore deposits, smarter mineral processing solutions are required to achieve sustainable and economic methods for mining and processing low-grade deposits. In order to make the treatment of low-grade deposits economically viable, large quantities of rock need to be mined and processed. The associated infrastructure costs (power, water supply, accommodation and support services, waste storage) result in a substantial penalty on the project, from both capital and operating cost perspectives. As a consequence, the challenge for the mining industry is to overcome the associated rise in energy and water consumption as well as increased project complexity when processing large amounts of low grade ore. Ore sorting technologies have been used for many years, predominantly on small projects, enabling the upgrade of marginal ores. Several sorting methods based on characteristics including specific gravity, radiometry, colour, particle size, grade and other detectable physical characteristics have been employed. The challenge for large low-grade ore bodies is to crush and sort at coarser rock size in order to minimise specific energy consumption in comminution and to reduce waste disposal costs. For large projects, the understanding of the economic impact of ore sorting is limited. The economic drivers include plant head grade improvement; sorting infrastructure capital, operating and maintenance costs; waste material handling and other environmental costs related to waste disposal. This paper analyses the economic impact of ore sorting in a large mineral processing operation. The focus of the analysis is to compare NPVs for a circuit including screening and ore sorting stages. A project for processing an Australian copper sulphide ore is considered as an example for this study."

Jan 1, 2014

By Rakesh Kumar, S. Mehrotra, T. Alex

"This paper, an overview of our recent findings on mechanical activation (MA) of minerals/materials, emphasizes the importance of sample genesis, mechanically induced/altered porosity and surface area, mineral interactions, glassy inorganic materials, surface alteration and zeta potential changes and, mechanically induced reactivity of solids. Materials investigated include Al-oxyhydroxides (gibbsite and boehmite), fly ash and granulated blast furnace slag. Planetary, attrition, vibratory and conventional ball mills are used for MA. Genesis of boehmite has been found to have a bearing on its behavior during MA. For example, BET specific surface area (SSA) of boehmite prepared by thermal dehydroxylation of gibbsite has decreased from 265 to 65 m2/g during 240 min of MA; in contrast, the SSA of hydrothermal boehmite has increased from ~2 to 36 m2/g. Mechanisms of surface area changes in the two boehmite samples differing in their genesis is explored. MA of gibbsite and its mixture with hematite/quartz using attrition milling has indicated that the presence of the second phase promotes amorphisation. Amorphous materials show signs of change in nature of bonding during milling as illustrated by MA of fly ash. Physicochemical changes during MA are not restricted to the bulk phase. The genesis of zeta potential changes in MA solids can be many; for example texture induced zeta potential changes as observed for gibbsite, while zeta potential changes during the milling of granulated blast furnace slag occur due to enhanced (possibly non-congruent) dissolution. Interesting manifestations of mechanically induced reactivity and its correlation with physicochemical changes are illustrated in terms of alkali leaching of boehmite and, hydration of MA slag. New findings reported here are associated with several open questions and are highlighted in the paper."

Jan 1, 2014

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"The ball mill performance relies on impact grinding, but it has disadvantage of the lower efficiency when the ore is finer; while tower mill relies on friction shear affection with high energy efficiency, which is considered to be one of the most potential fine grinding equipment all over the world. Generated by the agitator device, the internal media movement is complex because of comprehensive interaction of screw mechanism, cylinder structure and adjacent media, which is the key factor of grinding process. But the kinematics parameter ,such as speed, acceleration, stress and so on, of media motion cannot be obtained through traditional laboratory test method, which restricts deeply research on finer grinding mechanism seriously. In order to solve this problem, characteristics of media motion in tower mill is studied via the discrete element method. Coefficient of restitution, coefficient of static friction and coefficient of rolling friction are the key parameters affecting the media movement, which were calibrated by stacking angle test firstly. A 3kW tower mill is established as the model for simulation. At last one appropriate simulation strategy is selected to increase simulation accuracy. The characteristic of media motion is obtained based on the computer simulation analysis: macroscopically, the media in tower mill is a dynamic equilibrium state generally accompanied by spiral up and down movement all the time. And it has been found that the maximum lifting height is proportional to the rotation speed of agitator shaft. The velocity of media at the edge of screw stirrer is biggest, while the velocity of media near the cylinder wall is smaller, so the grinding performance between the two ring areas is the best. The rotational speed of agitator shaft and media filling ratio are the two most important operating parameters in tower mill. The impact curve of two main operating parameters on the grinding intensity and energy efficiency are obtained. All these can provide theoretical basis and technical support for operating parameters setting of industrial tower mill."

Jan 1, 2018

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By B. A. Kutlin

29% of the total ore mined in the Russian Federation for copper production is finely disseminated copper-zinc-pyrite ores of the Ural Region. Physical and chemical characteristics of pyrite copper-zinc ores make for difficulties in obtaining high indices during processing. At present, the authors have elaborated the technology to improve the quality of copper concentrates up to 20.0% for the ones obtained during pyrite copper-zinc ore processing (based on the example of the ore mining and processing enterprise ?Uchalinsky GOK?, Russian Federation). There are examples of use of fair-sized pneumo-mechanical flotation machines by modernization of processing plants. Keywords: copper-zinc-pyrite ores, Ural region Russian, selective flotation, pneumo- mechanical flotation machines

Sep 1, 2012

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By R. Singh

The present paper deals with the development of flotation based process for enrichment of a lead-zinc sulphide ore from Ganesh-Himal region of Nepal. Detailed characterisation and flotation studies were carried out under varying process conditions. The sample assayed 2.47% Pb with 13.6% Zn. The ore was predominantly made up of spahlerite and pyrite in association with subordinate amounts of galena, minor amounts of pyrrhotite and chalcopyrite. Dolomite was the main gangue. The modal analysis showed the probability of fair liberation of sulphides from gangues around 210 microns but the locking of galena with sphalerite and other sulphides continued to finer sizes. Under the optimum process conditions the rougher lead and zinc recoveries were 96.3% and 90% respectively. Multistage cleanings of rougher products proved helpful in improving the concentrate grade, meeting the required specification. Based on the studies undertake a process flow-sheet for the concentration of the ore to individual lead and zinc concentrates was developed.

Jan 1, 2014

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Caibin Wu, Ali Lei, Ningning Liao, Jingsheng Ye

"The particle size distribution characteristics of ground product can influence the quality of the classification overflow and the next beneficiation indexes in an ore concentrator. Usually, the size distribution of ground product is considered to be determined by that of new ball mill feed. However, based on large amounts of data from industrial grinding circuit surveys, this paper has clearly shown that the size distribution of ground product should be determined by the size characteristics from classification underflow unless the circulating load was small, because the new feed is an important component and occupy a dominant position of mixed ore from belt feed and classification underflow. On the other hand, the correlation coefficient of the size distribution between ground product and classification underflow can be more than 0.99 when the relevance principle and its method are used. Meanwhile, their P80 value also keeps a synchronous correlation. The greater the capacity of classification underflow is, the higher the correlation of size distribution between the ground product and the mixed feed is. Furthermore, the correlation coefficient of the size distribution between ground product and classification overflow which is from primary or secondary can be 0.96. It is another discovery that the correlation coefficient is related to the type of classifier. The coefficient of size distribution of overflow and underflow from hydrocyclone is superior to that of spiral classifier, which can explain the reason why the hydrocyclone is widely used to replace the spiral classifier in concentrator.INTRODUCTION It is well knows that ball mill circuits closed with cyclones or spiral classifier such as a primary grinding circuit, a secondary grinding circuit and SAB mill have become an industry standard. Which grinding process employed will be determined by the P80 value of ground products. When the primary closed circuit ball mill or SAB that it is different throughout between the two processes was employed, a grinding fineness with -200mesh under 68% will be available. However, the secondary grinding circuit with the fineness of -200mesh above 80% can be conducted. Of course, the grinding fineness is determined by the grain size characteristics of the mineral."

Jan 1, 2018

By Zhen Hu, Chenghang Wang, Jianjian Zou, Xiujuan Li, Hanwen Li, Tai Wang, Baoxu Song

A rare earth deposit in Sichuan, China is rich in wulfenite in addition to bastnaesite and barite, and the deposit has already adopted high intensity magnetic separation technique to pre-enrich the rare earth minerals, during which the wulfenite and barite have been left in the non-magnetic product. Because the chemical composition of wulfenite is only 24.17% Mo and 42.15% Pb, it is very hard to obtain qualified lead or molybdenum concentrates by physical separation process. To pre-concentrate the wulfenite, flotation has been first introduced, and by using 100g/t GY-7 as dispersant, 1500g/t CP-1 as depressant and 160g/t GY-4 as collector, a floatation concentrate assaying 15.52% Mo with a recovery of 86.12% was obtained. Then a leaching process was conducted by using 1.2mol/L Na2S as leaching agent, and molybdenum can be translated into sodium molybdate in the solution with a leaching recovery of 99%. To recover rare earth oxides (REO) and lead from the leaching residue, a magnetic separation process has been conducted. Above all, by the whole process, the molybdenum recovery reaches 86.16% in the sodium molybdate solution, and a lead concentrate assaying 54.59% Pb with recovery of 27.99% could be obtained.

Jan 1, 2014

By Stephen Simukanga, Jewette Masinja

"Mining has been going on commercially in Zambia for over 100 years. The backbone of the mining industry has been copper production and its by-products of cobalt and gold. Over these years, the mining industry ownership structure has swung from private ownership to state ownership in 1972, and back to private ownership in 1995. Environmental management was first introduced into the body of Zambian legislation in 1991 through the promulgation of the Environmental Protection and Pollution Control Act (EPPCA). The Act’s main functions included the protection of the environment and control of pollution, and in particular to provide for the health and welfare of the people, animals, plants and the environment in general. This Act, was replaced in 2011 by the Environmental Management Act (EMA). The new Act has a number of new elements including: mainstreaming environment in national planning, it provides for the domestication of multilateral environmental agreements, enhances public participation issue, creates a central environmental information depositary, elaborates access to information principles, establishes an environment fund, creates enforcement orders, provides for both Zambia Environmental Management Authority and members of the public to sue for damages following environmental pollution, and provides for the appointment of honorary Inspectors. In addition to this, the Mines and Minerals Act of 1995 provided, for the first time, a section on environmental management in the mining sector. This section also created the Environmental Protection Fund (for mining), and made it obligatory to undertake environmental impact assessment before mining permits could be issued. The Environmental Protection Fund has now been established, as provided for by the law, and currently has more than USD9.0 million in the account. Secondly, environmental auditing is now being carried out annually on mines around the country, the effect of this has been a significant improvement in the environmental management of mining in Zambia. This paper looks at the response of the Zambian mining sector to these pieces of environmental management legislation, and the direction that the mining sector is expected to take on environmental management going forward."

Jan 1, 2014

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By Jun Xiao, Jianwen Yang, Yanhong Dong, Daixiong Chen

"MANGOTE Surface oxidizied mine is a gold-bearing deposit in Congo's Mai-Ndombe Province. In the past decades, the ore has been exploited in a crude way by local farmers, which directly causes the severe processing difficulty and lack of economy of cyanide leaching. Hunan Research Institute for Non-ferrous metals (HRIM) is currently investigating options to recover gold through understanding the mineralogical characteristics of MANGOTE surface oxidized ore. Chemical analysis , X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANing electron microscopy (QEMSCAN ) were conducted on samples from mine site. The bulk analysis results showed that gold separation of gold from gangue minerals was feasible after grinding the ore samples to 86.53% -74µm and adjusting the pulp specific weight at 100g/L, and gravity separation was conducted with using spiral chute after grading of fine particles. The research results highlight relationship between mineralogical characteristics of abandoned ore and economy of comprehensive utilization that might be directive experience to similar cases. INTRODUCTION The occurrence state of gold in natural gold minerals determines the basic recovery and recovery effect of gold(Komnitsas, C., & Pooley, F. D. 1989). The occurrence of gold in the ore refers to the form of gold in the ore.Generally the existing state of gold can be divided into four major categories according to the viewpoint of the dispersion system: independent minerals and gold, a coarse dispersed system;colloidal gold, a colloidal dispersion; solid solution gold, is atomic ion dispersion; adsorptive gold, according to the adsorbed particle is the micelle or ion, respectively is a colloidal dispersion or ion dispersion(Mao, S. D., & Yang, R. S. 2009; Liu, J. J. et al. 2007; Horisberger, M., & Rosset, J. 1977; Li, Y., & Audétat, A. 2013).With the increasing technology of comprehensive utilization of resources,varied plants can now process different gold ores with various occurrence states(Neesse, T. 2014; 7. Ogundare. et al.2014)."

Jan 1, 2018

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By Z. G. Guan

The tungsten ore in Xingluokeng belongs to a symbiotic deposit containing granite and fine vein-type wolframite and scheelite. The tungsten (WO3wolframite) accounts for only 0.233% of the raw ore, 49.60% of the , 49.60% of the scheelite and 0.8% of the tungstite. The dissemination size of the tungsten ore is extremely uneven, with 0.02~1.28 mm for scheelite and 0.01~1.28 mm for wolframite. The dissemination size of scheelite is coarser than that of wolframite. The size of 83% of scheelite and 60% of wolframite is greater than 0.04 mm. The composition of minerals in the ore is quite complex. The major metallic minerals include wolframite, scheelite and pyrite, which are followed by molybdenite, chalcopyrite, arsenopyrite, limonite, magnetite, hematite and siderite. The major gangue minerals include quartz, feldspar, muscovite, biotite and sericite, which are followed by chlorite, fluorite, apatite, dolomite, etc. According to the dissemination features and liberation degree of the tungsten minerals, the technology flowsheet of gravity concentration for coarse particles and flotation for fine particles to re-cover the low-grade and fine vein-type tungsten minerals is adopted, and -0.7 mm is selected as the processing size. The closed-circuit grinding procedure, with the combination of the rod mill and high-frequency vibration screen, is adopted. The grinding product is classified into three products of -0.7 +0.2 mm, -0.2 +0.04 mm and -0.04 mm. The gravity separation is adopted for the former two to recover tungsten minerals and the flotation is adopted for the last one. Under the condition that the raw ore contains 0.23% WO3, some technology indexes of beneficiation have been achieved. The gravity tungsten concentrate contains 63.54% WO3 with the recovery 70.11%. The slime flotation tungsten concentrate contains 35.22% WO3 with the recovery 10.48%. The composite tungsten concentrate contains 57.53% WO3 with the recovery 80.59%. Thus, the tungsten minerals are re-covered effectively.

Jan 1, 2014