Search Documents

By S. Serranti

The recycling of end-of-life concrete into new concrete is one of the most interesting options for reducing worldwide natural resources use and emissions associated with the building materials sector. The possibility to realize a larger re-use of silica aggregates from old concrete, strongly contributes to reduce environmental impact (reduced exploitation of natural resources, reduction of CO2 emissions, airborne dust production, etc.).To reach this goal, innovative processing techniques, as well as innovative sensing units and architectures have to be developed. In this perspective an analytical approach, based on hyperspectral sensing techniques, is proposed, discussed and critically evaluated in order to perform an automatic quality control assessment, finalized to maintain a high standard of concrete demolition waste, from the earliest stage of recycling to the further processing stages, according to the detected in-situ demolition waste characteristics. The paper deals with the analysis and the evaluation of the problems related to the integration of this approach with state-of-the-art demolition and building processes and procedures. Keywords: end-of-life concrete, recycling, hyperspectral imaging, NIR spectroscopy, quality control

Sep 1, 2012

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By V. E. Dementiev, V. I. Kulikov, G. I. Voiloshnikov, Yu. O. Fedorov

"The report presents the summary of the JSC Irgiredmet’s activities in the field of preconcentration of ores. As of 2018, the Institute has almost 40-years’ experience in this area. Over the years, Irgiredmet has done a lot of work – from development to implementation of new technologies of ore piece sorting and concentration based on X-ray radiometric separation (XRRS). INTRODUCTION Preconcentration has been a challenging issue of the mining industry over the last decades. The implementation of this technology can significantly increase mining efficiency. The main application of preconcentration is improvement of mined ores quality, however new and more complex issues have arisen with the evolution of the technology. Irgiredmet has started to develop an efficient preconcentration technology for gold-bearing and rare-metal ores 40 years ago. The X-ray radiometric method widely used at that date as a method of elements determination in geology and geophysics become the ground for this work (1). Since that time, the Irgiredmet Institute has developed and significantly improved the technology of piece ore sorting, or XRRS (2-5), that is currently also known as the X-ray fluorescence method. The progress of the XRRS development achieved by Irgiredmet in cooperation with Rados LLC, Tekhnoros LLC (Krasnoyarsk), Rados-Service LLC and CJSC Tekhnogen (Ekaterinburg) has proved efficiency and applicability of the XRRS technology for processing a wide range of minerals and solving of various technological problems (7-9) compared to other radiometric methods (6). Furthermore, obtained results are supported by numerous studies, trials and implementations. The significance of ore preconcentration for greenfield and brownfield projects determined the establishing a new subdivision of Irgiredmet, the XRRS Technology Center (XRRS TC), that has provided the Institute with a completed range of processing technologies, from preconcentration to producing final products. Over the past few years, the XRRS Technology Center has carried out studies and testing of a numerous (more than 100) projects, mines and deposits of gold-bearing ores, rare metal ores (Be, Ta, Nb, W, Mo), base metal ores (Cu, Sb, Zn, Pb), ferrous metal ores (Fe, Ti, Cr), rough diamonds and coal. The XRRS Technology Center performs various specific studies and testing not only in Russia, but as well as in Kazakhstan, Georgia and Mongolia. Mines and companies from Chile, India, China, Iran and other countries also take an active interest in the XRRS technology."

Jan 1, 2018

By Ashish Agarwal

For a correct evaluation of the performance of any process, it is important to reconcile the data gathered in the plant from the material balance point of view for all the streams flowing in and flowing out of the process unit. There are two main approaches to reconciliation of data, which involve minimization of the sum of the squares of: (i) the closure residuals and (ii) the component adjustments; both weighed with the estimated variances of the components. Though, these approaches have served us well, it has not been possible to ascertain if the reconciled values for various components and the split factors obtained using these approaches are truly the best estimates. In this paper, this aspect has been investigated by analyzing pseudo-experimental data of known error structure on size classification of particles in a hydrocyclone. Three types of basic error structures were considered for the measured component values: absolute error, relative error and chi-square error. The error structure was modified by adding a random component of error using normally distributed random numbers corresponding to zero mean and different levels of variance. By carrying out a large number of simulation experiments, it has been shown that in the presence of random errors, irrespective of the basic error structure of data, which is usually unknown, the chi-square error minimization criterion can be used to obtain most reliable results. Keywords: data reconciliation methods, chi-square error minimization

Sep 1, 2012

By Diana Drinkwater, Tim Napier-Munn

"This paper argues that, although specialist mineral engineering expertise is essential for the efficient design and operation of mineral processing plants, the environment in which these skills are supplied to the industry has changed forever, and not for the better. Most of the mineral engineering programmes in western universities have died or are dying. The long-service mine site mentors have gone, operations are run on a staffing shoestring so that there is no longer the time (or inclination) for considered decision-making, and the FIFO model has discouraged continuity of optimisation projects and communication between professionals. At the same time the technical challenges of designing and operating effective process plants are increasing. These trends are not going to be reversed any time soon, if ever. The ability to run efficient mineral processing operations has been materially compromised as a consequence. We propose that well-designed professional development can help to recover this situation, and it can be done easily and cheaply. The workplace is the best environment for such skills development. Professional development training should be integrated with normal duties throughout the early years of a graduate’s service (and probably beyond), and the cost should be regarded as non-discretionary expenditure for the business. If such programmes are properly resourced and managed and extended over longer time periods, there will be a measureable rise in the level of technical understanding and competence within companies and a resulting beneficial impact on resource utilisation and thus shareholder value. The paper outlines some of the approaches that we believe will work, and the benefits that we expect will accrue."

Jan 1, 2014

By A. Lane

Africa is ripe with opportunity for the mining industry. The continent has large, and relatively unexplored mineral deposits, and recent high economic growth rates have meaningfully improved the political, economic, and infrastructural environments. However, these opportunities are accompanied by significant risks, including resource nationalism, uncertain regulation, corruption, and continuing political instability (up to and including war). Forward-looking companies actively manage these risks by creating a sense of shared purpose with the countries and communities that own the resources, using tools such as stakeholder analysis, local narratives, scenario planning, and constituency engagement. They also measure socio-economic impact to insure the creation and demonstration of shared value.

Sep 1, 2012

By J. Bhattacharya

In many different ways industrial raw materials resources industry as a whole has accepted the principles of sustainable development and has made a commitment to move toward this goal. The critical question now is ?how?? While many companies have adopted policies and are implementing community relations programs, sustainability is not always ?lived? throughout the organization. While traditional programs and commitment from the top are critical, employees within all functional areas can advance sustainability. Individuals can make difference at all organizational levels, and it is this collective action that is so critical for enhanced financial performance as well as the preservation of the industry. Keywords: value chains, sustainability, legislation, auditing process

Sep 1, 2012

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012