Search Documents

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By V. E. Dementyev

This paper presents a brief overview of some IRGIREDMET advances in gold hydrometallurgy. Original impulse-percolation technology and equipment for intensive cyanidation of gravity concentrates have been developed and introduced into industrial practice by IRGIREDMET since 1980s (RF Patents N1593250). The process is based on leaching using special hydrodynamic and reagent conditions providing high dissolution rate for coarse gold particles. Gold and silver are precipitated from pregnant solution by cementation or electrowinning. There was also proposed an im-proved cementation method using zinc in a contact with electrically conductive material. The units including closed water recirculation, tails detoxification and semi-dry tails IRGIREDMET is well experienced in gold adsorption technology using ion exchange resins and activated carbons. The comparison of CIL and RIL processes were done for a number of gold mines, for example for Sukhoi Log gold deposit. The properties of prospective foreign and domestic ad-sorbents including strong-base, bi-functional and weak-base resins as well as activated carbons were studied. The Institute has developed some adsorption/elution technologies and equipment, such as a two stage RIP adsorption technology for gold/silver ores, an improved technology for gold elution from loaded resin and carbon, electrowinning cells for gold recovery from RIP and CIP eluates etc. Large scale ?Resin In Pulp? tests using weak-base resin were finalized and process design criteria were developed. Gold plant design is on progress at the moment. Improved technology for carbonaceous (preg-robbing) gold ores was developed. It was tested for some gold deposits including Sukhoi Log. It allows to overcome preg-robbing activities of ores treated and to improve dramatically performance of cyanidation and adsorption circuits. The studies on refractory gold ore treatment including bio-oxidation, pressure oxidation, roasting and ultra-fine grinding were conducted. Heap leach technology was tested and introduced by Irgiredmet for a number of Russian mines. Zinc cementation, activated carbon and ion-exchange resin adsorption were used for gold recovery from pregnant heap leach solutions. The options including combined technology ?Heap leach/ RIL or CIP? for clay ores were also developed and tested. The plant using developed technology is at construction stage now. The study on In-Situ gold leaching was conducted. The comparison of different gold lixiviants for this purpose was carried out. Gold recovery from pregnant leach solution by activated carbon and anionite including gold elution from loaded adsorbents etc. was also studied. In 2000 the In-Situ leaching technology was commissioned at Maminskoye gold deposit (Ural). The technologies for treatment of complex ores and by-products were proposed. For example, the technology of gold, silver, copper and zinc recovery from calcines after sulphuric acid production was developed.

Jan 1, 2014

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Andrey V. Tarasov

"An environmentally clean and virtually waste-less technology for treatment of domestic and industrial solid waste (HGIW) including other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations.The essence of the process is that the HGIW are decomposing in the liquid base in air-bed slag melted layer under the temperature of 1350-1400°C.HGIW is considered as fuel heat-producing energy of 1500-1800 kCal/kg with 51,7%.Processing of municipal and industrial solid waste in molten slag is carried out autogenously without additional fuel, the blowing is enriched by oxygen up to 50-70%.The complex makes it possible to treat the furnace charge without preliminary drying and sorting with big differences in chemical and morphological composition due to the versatile firing chamber.The proposed process resolves the acute and globally significant problem of dioxin formation.The purpose of the proposed technology is to ensure such destruction of the structural lattice that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. It was established the required preconditions to achieve this purpose."

Jan 1, 2003

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

By Matti Kongas, Kari Saloheimo, Antti Remes

"The paper studies the control performance of the flotation process as a function of the measurement accuracy and sampling frequency of an on-stream XRF analyzer, using a simple dynamic model. An additional aim is to assess how the economical result of a mineral flotation process depends on the quality of process control based on the on-line elemental assays.An on-stream XRF analyzer measures the concentrations of slurry lines in a continuous cycle from several process points. The control performance depends on the analytical accuracy and sampling frequency of the concentration measurement. With a long cycle time, the state of the process changes before a new measurement becomes available. With short measurement times the statistical variance of the counted X-ray pulses increases, increasing the random error in the analysis. In addition, the measurement accuracy depends on the concentration of the component to be measured from the slurry.To quantify the effect of analysis error and frequency to process control, a simple dynamic process model is created in the Matlab environment. Data from a copper flotation circuit is used as a test case. The process model comprises a first order reaction equation and the grade-recovery -relationship estimated from process data. The control was modeled using the control strategies implemented into a rule based advanced control system.The economical performance of the control was studied by calculating the overall net smelter return at various analyzer parameter combinations. The economical performance of the process declines strongly when the sampling cycle is increased. In studied case the sample measurement time did not have a significant effect on the results. The economical performance of the simulated process corresponds to an almost uncontrolled process when sampling cycles longer than 40 min are applied."

Jan 1, 2003

The ultimate goal of a mineral processing plant is to recover as much of the target mineral(s) as possible from the ore being treated to achieve the best economics. Selection of the mineral processing techniques is the most important step in achieving this goal. However, due to the complexity of the ore, the recoveries of valuable minerals may be not satisfactory even when the mineral processing technique(s) are well chosen. In other words, minerals of interest can be lost to the tailings for mineralogical reasons. For example, gold is mainly extracted from the ore by gravity, flotation, cyanidation, or a combination of these processes, and high recovery (>90%) can be achieved when gold occurs as coarse grains. However, when a refractory ore is being processed, gold extraction will be challenged by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery mainly include grain size, shape, surface coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking in sulphide, silicate and other minerals as fine-grained gold inclusions and/or as invisible submicroscopic gold is by far the most common factor leading to poor gold recovery encountered in gold ore processing. Processing of PGE ores faces the same challenges as gold. Small grain size and locking of PGM in sulphide and non-sulphide minerals often cause PGM losses. When silver ore contains significant amounts of pyrargyrite, proustite and stephanite, silver recovery by cyanidation can be very low because of the slow dissolving kinetics of these minerals. In the processing of base metal ores, high content of pyrite, intergrowth of chalcopyrite with sphalerite and presence of clay miner-als may cause problems in recovering Cu-, Pb- and Zn- bearing minerals. Process mineralogy helps address all issues and problems related to mineral processing with predicting and trouble-shooting being two major objectives. It provides useful information on process selection, flowsheet development, recovery improvement and reagent consumption optimization. The information acquired from a process mineralogical study can be used as a guide for a metallurgical testwork program for process design or optimization.

Jan 1, 2014

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

The aim of this paper is to evaluate the suitability of a coal sample from the mine Jaworzno (Poland)- locality for bacterial leaching. Laboratory research used a pure bacterial culture of Thiobacillus ferrooxidans. The results showed that bacterial leaching was effective, with a one month leaching time, when 65% of total sulphur and 85% of pyritic sulphur was leached. The paper describes changes to the pyrite during and after bacterial leaching.

Jan 1, 2003

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc.In this paper, we focus on grinding process considered as the most costly and power consuming node of the mineral processing scheme. Different objective-oriented levels of data clustering will be addressed.First, the evaluation of grinding operation taking into account data and constraints from all processes before (e.g. blasting, crushing) and after (e.g. flotation, leaching, etc.) the grinding node. The second level deals with process diagnosis by differentiating operation level and identifying behaviour drifts. Control and optimisation are two other levels concerned here with the selection of optimum trajectories in the drift correct.Industrial plant data are processed in order to illustrate the feasibility and the potentiality of MDA applications in addressing the clustering and interpretation of grinding mill behaviour."

Jan 1, 2003

By L. Kuzev

Unknown and unpopular vibrational grinding mills possibilities to horizontal working chambers have been discussed. They can be realized under normal conditions with the typical values of vibrations applied with vibrational grinding which are: vibration frequency from 15 Hz to 50 Hz, vibration amplitude to 6 mm and vibration geometry. These possibilities constantly increase involving new raw materials and processes. Vibration grinding is possible with other technological process accompanied by intensified technological processing, while the process decreases. In many cases these technological decisions are original.

Jan 1, 2014

By Peter N. Holtham, Geoffrey J. Lyman, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong, Tim Napier-Munn

Studies of the dense medium and classifying cyclone have been conducted using the Fluent computational fluid dynamics code. Experimental measurements of the segregation of medium in a DM cyclone by gamma-ray tomography and the performance of a novel classifying cyclone design have been used to test and interpret the 3D CFD predictions. The predictions of the CFD models were generally plausible, though more work is required to incorporate turbulent mixing of the slurry in the cyclone. The benefits of the novel cyclone design were explained by the model in terms of conditions favouring reduction of short-circuiting at the vortex finder, and the removal of the air core from the wall at the apex. Work is continuing.

Jan 1, 2003