Search Documents

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By A. Oleynik

The paper presents the modeling and simulation experience in field of research into the mineral row material separation. Features of the subject domain generate a need of different approaches using for modeling and simulation. The general scheme of separation modeling process and some examples of developed simulators are presented. Due to different features and standards of knowledge, different formal models should be used to describe and analyze separation processes in the frame of general scheme. The main types of simulators are modeling tools based on statistical, analytical or expert (logical) methods. Advantages and disadvantages of each method above are mentioned in the paper. Based on the studies in the field considered, an aggregated mathematical model of a separation process has been generated. The aggregated model is presented by two combined equations. The actual apparatus model is formed by substitution of the particular functional expressions of the forces acting in the apparatus into the aggregated model. The developed simulation tools are based on integration of limited experimental data and on ex-pert knowledge available on separation processes. Simulation does not allow producing an optimal, in terms of mathematics, solution. But it gives an opportunity to produce and compare quite adequate solution variants in real time. The results obtained are the theoretical and methodological base for integrated information technologies to support studies in the field of mineral processing.

Jan 1, 2014

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

By Tuan V. Nguyen, Louis Mittoni, Murray Rudman, CSIRO Minerals, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D “Improving Thickener Technology” project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

By Matveyeva Tamara

The main deposits of gold-sulfide ores of Russia are characterized as refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold, the low gold content (3-5 ppm) and non-uniform distribution of the gold associated with pyrite and arsenopyrite. These ores show low indicators of extraction of gold and silver at cyanidation. Flotation is one of the basic technological procedures of processing of gold sulfide ores however simultaneous presence of pyrite and arsenopyrite and lack of effective methods of their selection constrains application possibility of flotation schemes because of rigid requirements to flotation concentrates under the arsenic content and practically excludes smelting of pyrite concentrate. The main losses of precious metals at flotation technologically are concentrated in thin classes (up to 15 %) demonstrating an inefficiency of standard reagent modes. For an estimation of expediency and possibility of application of selective flotation of pyrite and arsenopyrite a scientific substantiation of the mechanism and criteria of selection of gold-bearing ferrous sulfides of various material structure is developed and for difficultly divided pairs of sulfides with close technological properties the new selective reagents providing effective extraction of gold from hard-to-beneficiate ores are designed. The original technique for modifying surface composition of natural sulfides by nano-sized Au is worked out and the mechanism of selective adsorption of new reagents ? oxypropyl ester of diethyl-dithiocarbamatic acid (OPDTC) and oak bark extract (OBE) on Au-bearing sulfide minerals is revealed. Formation of almost insoluble OPDTC-Au compounds is defined by methods of scanning electronic microscopy (SEM) and UV-spectroscopy. Application of developed reagent modes using new reagents have been tested in laboratory conditions at flotation gold-sulfide ores samples and collective concentrate probes providing high extraction of gold and improved quality of the concentrate (less than 2 % As). Keywords: pyrite, arsenopyrite, selective flotation, flotation reagents adsorption, complex-forming, gold recovery.

Sep 1, 2012

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By S. Titkov

At present, Russia is engaged in processing, 3new plants of hard-to-process potash ores with increased content (up to 10 - 12%) of insoluble impurities (insoluble residue ? I.R.). This required additional research to improve the process of potash ores flotation. Based on the study of the effect of dispersive properties of frother and its flow rate on the efficiency of aliphatic amines with different length of the hydrocarbon radical (as sylvite collector) there was showed the possibility to apply high molecular amine with length of hydrocarbon radical C20 ? C26 by normal temperature of circulated plant salt solution (saturated solution KCl ? NaCl ? H2O). There was designed and tested in plant conditions the modified amine collector with the length of the hydrocarbon radical C16 - C26, improving flotation of Sylvite under normal temperature of circulating salt solutions at potash flotation plants. There was made the study of the influence of the hydrocarbon radical length of alkylmorpholine on the Halite flotation from intermediate products of sylvite recleaner flotation with different content of I.R. (silicate-carbonate slimes), at normal and elevated temperature of salt solution. On the basis of the application of modified alkylmorpholine for Halite flotation, there was developed the process of further beneficiation for the intermediate products of sylvite recleaner flotation from potash ores with increased content of insoluble impurities, which can eliminate the circulation of the intermediate products in the process flow sheet of sylvinite ore processing and increase the KCl recovery into the finished product. Keywords: flotation, potash, halite, alkylamine, alkylmorpholine

Sep 1, 2012

By Y. M. Zhao

The dry coal preparation technology based on air dense medium fluidized bed is an innovative dry highly efficient technology of coal by introducing fluidization technology into beneficiation.. A modularized 40-60 tones/hr system (KZX-40) with an air dense medium fluidized bed separator was established. The construction cost of the modularized system is only 1/3 of the traditional wet heavy-medium coal preparation plant construction cost with the same capacity, and the consumption of dense medium can be reduced by 50%-60%. The footprint and volume of the system are decreased by 75% and by 89.81%, respectively. These facts show the improved intensity, efficiency and economy of modularized coal preparation technique. The modularized KZX-40 system can be used to separated 50-6 mm coal over a separation density range of 1.3-2.2g/cm3 depending on the variation of <1mm fine coal content. The separation efficiency of the system was investigated at low and high separation densities by float-sink experiments. The partition curve of the products at low separation density shows that the separation density (d) is 1.33g/cm3, and the probable error (E) value is 0.05g/cm3. Using 50-6mm coal with an ash content of 55.35% as feedstock, at a high separation density of 1.61g/cm3, the clean coal with an ash content of 14.67% and the tailing with an ash content of 71.26% are produced with an E value of 0.06g/cm3. It is clear that the modularized KZX-40 system is suitable for separating 50-6mm coal effectively. During the dry coal preparation process, the dust is removed by the bag collector and recycled back into the separator. So the system has the advantages to work without environmental pollution and water. The modularized system greatly reduces the construction and operating costs and decreases the area and volume required, compared with wet dense medium system. The system is applicable to the coals located in arid regions and also to the coals that tend to slime during wet separation. Keywords: modularized, KZX-40, fluidized bed, beneficiation

Sep 1, 2012

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By S. Banisi, E. Arghavani, Gh. Parsapour, S. Mousavi

Maximization of water recovery in thickeners is an essential step in the mineral processing industries. The Gol-E-Gohar iorn ore processing plant uses a center pier thickener with a diameter of 38 m and depth of 4 m. The feed rate is 50 t/h solids with a concentration of 5% (w/w), and it has been designed to provide an underflow containing 50% solids. The performance of the thickener was not as expected judged by the overflow stream containing 0.6% solids and water loss of 52 m3/h in the underflow. A criterion called the index of flocculation incorporating the perimeter-based fractal dimension of flocs, floc size, and settling velocities was proposed and used to determine the optimum flocculant dosage which was found to be 20 g/t. The fractal dimension of flocs in a pulp containing 5% solids was found to be between 1.16 (no flocculant) and 1.56 (40 g/t flocculant) which indicated highly branched and loosely bound structures for the flocs as flocculant dosage increased. At these conditions, the size of the flocs which was recorded by a digital microscope increased from 93 µm to 403 µm. A new feedwell with a special design with the aim of preventing flocs breakage and maximizing energy dissipation of pulp was constructed and installed. These modifications led to an increase in the thickener drivehead torque from 5% to 18% of the rated torque, indicating a higher bed depth. Finally, installation of a PID controller reduced the drivehead torque relative oscillation from 52.0% to 12.7%. These changes increased the solids concentration of the underflow from 49.0% to 56.9%, decreased the overflow solids concentration from 0.6 % to values smaller than 0.01% and resulted in a reduction of 27% in water loss in the thickener underflow.

Jan 1, 2014

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012

By R. D. van der Weijden, W. F. C. van Wageningen

"Copper(II) can be recovered or removed from acidic copper sulfate solutions as cuprite or metallic copper powder by reduction with carbohydrates (van der Weijden et al., 2001, 2002). In order to make this process suitable for a commercial scale pipe reactor, process conditions and reactor configuration need to guarantee proper throughput of the dilute suspension. This is where crystal engineering also comes into view. Copper powder characteristics, such as size and shape of particles, influence the tendency to adhere to reactor walls and to agglomerate, which in turn influence the throughput. Furthermore, separation, drying, packaging and product quality, are dependent on the powder characteristics.In this paper the effect of both chemical and physical parameters on the shape and size of particles were systematically studied in a number of autoclave experiments. These parameters include mixing, Cu(II) concentration, pH, temperature, seeding, use of additives and reactor materials. Additionally, Monte Carlo simulations of copper growth inside a Kenics static mixer were made. Results show that the use of additives, and the use of static mixers influence particle characteristics the most."

Jan 1, 2003

By F. M. Zafar Kaifi

Magnesite producing companies rely on high grade purity MgO. The mineralogy of magnesite has a significant impact on the manufacturing of magnesite bricks. The manufacturing process of bricks companies utilizes 90% magnesite from 85%~90% MgO. The main objective of the magnesite bricks was to utilizes the indigenous raw material available in bulk quantity. With better under-standing of chemistry of the mineral species and strict control of bricks manufacturing/processing conditions can be better produce efficiently, a low cost high quality bricks with minimum detrimental environmental impact.

Jan 1, 2014

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By Jacek Kolacz

A new sensor based sorting system related to complex image analysis has been developed at Comex AS - Norway. It makes it possible to separate different mineral particles regarding their color, shape, texture, size, density and indirectly their composition. The sorting system has been successfully tested and applied for sorting minerals providing high separation efficiency in the range of 95-99.9 %. The main advantage of this system is connected with its universality where many material parameters are analyzed in the same processing unit by a single passage.

Sep 1, 2012

By Å Sandström

Loussavaara-KiirunavaaraAB?s (LKAB) iron ore mine, Kiirunavaara, is of magnetite type and associated with apatite, a calcium phosphate mineral. Rare earth elements (REE) have been found in connection with the apatite but also in other minerals. An apatite concentrate was produced by flotation, in order to investigate the possibilities to extract REE from the apatite by hydrometallurgical means. The content of rare earth elements calculated as oxides (REO) was 0.44% in the concentrate. Initially, leaching was done with large excess of sulfuric acid, hydrochloric acid, and nitric acid to study the REE solubility with different acids. In sulfuric acid, the leaching recoveries of the different REE varied between 35% and 69%. The reasons for the relative low recoveries, were that the rare earth elements precipitated together with huge amounts of gypsum, that was formed during leaching. However, both hydrochloric- and nitric acid gave almost complete extraction of the REE into solution. Analysis of the small leaching residue obtained, revealed, that mainly the light REE remained in the residue indicating that a small part of the light REE were present in the concentrate, in some acid, insoluble mineral other than apatite. With the aim to separate the REE from the phosphoric acid, the solutions from hydrochloric- and nitric acid leaching were neutralized to a pH of approximately 2 with ammonia. During neutralization, REE were precipitated as phosphates with good recoveries and a concentrate of 10.5% REO suitable for further upgrading was obtained, while the remaining solution can be used for fertilizer production. In further solvent extraction studies, it was shown, that after re-dissolution the REE could be effectively extracted by Cyanex 923, thus allowing for purification from calcium and phosphate ions. The REE were finally stripped from the organic phase and a REE nitrate solution was produced. Keywords: apatite, rare earth elements, REE, leaching, solvent extraction, cyanex 923

Sep 1, 2012

By M. Blagojev, R. Tomanec

"Studies reported in this paper used polymetallic Pb-Zn-Sb-As-(Ag, Au) ore from Dražnja, Kosovo. The ore is comparatively rich in Zn (6.56%) and Pb (2.87%), but with high rates of Sb and As. Conventional lead and zinc concentration by flotation produced galena and sphalerite rich concentrate with high recovery, but with excessive As and Sb. After chemical analyses, which could not detect the reason for the excessive elements, ore minerals were identified under the ore microscope, their texture characterized, and degree of liberation of useful minerals was assessed. Microscopy of the mineral concentrates revealed complex intergrowths of galena and marmatite minerals mostly with sulphosalt minerals (boulangerite, jamesonite and bournonite) and also with arsenopyrite mainly responsible for the unsatisfactory quality of the concentrate. These complex sulphosalts, among other things have similar behaviour during the flotation concentration, and in spite of their interlocking with galena, therefore inadequate liberation, sulphosalts remain in the lead concentrate. Microscopic analyses indicated that a better galena concentration product is possible with a higher rate of mineral liberation, and then by selective floc flotation of some sulphosalt minerals. Purpose of this work was to show that only chemical analysis is not sufficient, according to that we solved the problem by precise mineral identification and time consuming mineral liberation measurements. INTRODUCTION The polymetallic Pb-Zn-Sb-As-(Ag, Au) ore body of Dražnja, Kosovo, fairly rich in Zn (6.56%) and Pb (2.87%) was repeatedly explored and once even worked. Mineralization at Draznja was primarily represented by sphalerite, galenite and marcasite/pirite. Some sections comprise massive sulphides, and others are lower grade zones of semi-massive sphalerite/galena or marcasite/pyrite dominant sulphides. The ore body II was formed in the southern gallery in the structure Çukë – Lajthishtë (with content of 3.16% Pb and 7.31% Zn). Pb-Zn ore with increased content of As, Sb sulphosalts is not rare phenomenon in the world. While previously treated as unprofitable, economical uninteresting ore, today with development processing and new reagents (organic, ecologic), are the topic of scientific papers. The examination of Pb-Zn ore with high content of sulphosalts we find in deposits as: The hydrothermal vein deposit of Harja in the Baia Mare area, contain a wide variety of sulphosalts [Cook, N. & Damian, G., 1997]; also the deposits Fankou Mine in Guangdong Province and the Dachang Mine in Guangxi Province, where the flotation concentration of galena and jamesonite takes place [Runqing Liu et al. 2015], [Zhang Ting, Qin Wen-Qing, 2015];. On a samples from Tibet in China flotation separation test of galena and jamesonite was conducted [Sun Wei, Han Haisheng, Tao Hongbiao, Liu Runqing, 2015]. According to history of investigation, the mineralized area of Dražnja has a long history of exploration and possible exploitation activities [Slowey, Galen, 2009]. Recent workings were carried out in three stages through the 20th century."

Jan 1, 2018