Search Documents

By T. Fraszczak, U. A. Peuker, T. Mütze, T. Leißner, A. Wikedzi

The present paper highlights on the comminution and liberation properties of two greisen-type lithium bearing-mica ore blends (L1, L2) subjected to different breakage devices; cone crusher (CC), roller crusher (RC), rotor beater mill (RBM) and a screen mill (SM). The particle size distribution (PSD) of the products from each device were evaluated to search for an appropriate PSD model using Gates-Gaudin-Schuhmann (GGS) and Rosin-Rammler (RR) functions. In order to determine an appropriate function that could better describe the PSDs from the devices used, the coefficient of determination (R2) was used as a criterion. In terms of mineral liberation studies, due to costs, only products from rotor beater mill (RBM) were examined through an automated scanning electron microscope (SEM) technique. It was found that RBM, RC and SM products were better described by the RR model than the GGS model with higher R2 values (0.97-1.0). However, cone crusher products for L1 were better described by GSS model, while that for L2 were better described by RR model. In terms of the spread of size distribution as indicated by RR model parameters, RC products were more uniformly distributed compared to products from other devices, for both ore blends. Also the RBM products were more scattered than products from other devices. The results indicate that the composition of individual ore blends affected the comminution products PSDs since different PSD model parameters were obtained for samples comminuted by same devices. The modal mineralogy of the two ore blends indicate both to be rich in quartz, topaz, zinnwaldite and muscovite. Further, the result indicate that, for both ore blends, zinnwaldite phase is more enriched in the fraction < 250 µm. Moreover, better liberation of zinnwaldite is observed for L1 compared to L2. This could be explained by differences of the two ore blends in three aspects; the nature of mineral association, reduction ratio of the fractions analysed and the nature of spread of the size distribution.

Jan 1, 2018

Coal preparation plants usually operate with water in a closed circuit mode. In this practice, large quantities of water is continuously being recycled. To compensate the natural losses, only small quantity of fresh make up water is added into the circuit. As a result, a gradual build up of residual concentrations of flotation reagents (frothers, collectors, coagulates etc.) take place in the water and the concentration levels of the contaminants increase. Besides, the recycled water accumulates higher amounts of total dissolved components (1600 ppm) and hardness (740 ppm) than the fresh water. Nearly 80 ? 85% of the process water used in a coal preparation plant is utilized in treating the coal fines in flotation circuit. The presence of certain alkali earth metal ions (e.g., Ca++, Mg++) may adversely affect the flotation performance as they precipitate sparingly soluble hydroxyl complexes on the coal surface and change its surface charge. These studies showed that the use of recycled water in flotation has a significant effect on the selectivity and kinetics of the flotation process because, the dissolved compounds, both inorganic and organic, alter the chemistry radically. By treating the recycled water through a softening process, the concentrations of alkali earth metals and hardness were reduced significantly. The concentration of alkali earth metals and hardness were reduced to 10 ppm and 35 ppm respectively in the softened recycle water. From the selectivity studies, it has been observed that the flotation yield and recoveries increased by four to seven units by softening the recycled water. The kinetic studies indicated that the clean coal particles followed first-order kinetics. The kinetic parameters namely, flotation rate constant (k) and maximum recoveries (R8) of flotation, were found higher with softened recycle water than the recycled water. This reduces the residence time in the flotation cell and thereby, increases its productivity. Keywords: coal flotation, hardness of water, water chemistry, softening process, selectivity, kinetics, flotation rate constant and maximum recovery

Sep 1, 2012

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

By William Skinner, Jennifer MacCarthy, Jonas Addai-Mensah, Ataollah Nosrati

"Acid leaching in agitated tanks is central to hydrometallurgical processing for valuable metals’ (e.g., copper, gold, nickel and cobalt) recovery from low grade (e.g., < 2 wt.%) ores. In this study, atmospheric leaching behaviour of Australian saprolitic nickel (Ni) laterite ore using sulfuric acid was investigated under isothermal, batch conditions at pH 1. The effect of primary process variables comprising time (4 h) and temperature (70 and 95 oC) on the leaching mechanisms and kinetics was established for -2 mm, low grade (~1 % Ni) saprolitic ore dispersions at 40 wt.% solid loading. Leaching proceeded incongruently, reflecting the proliferation of gangue minerals’ constituent elements (e.g., Mg, Al, Fe) alongside Ni and Co in the pregnant leach solutions (PLS). Subsequent analysis showed that 89% Ni and 78% Co were extracted after 4 h at 95 oC whilst at 70 oC the recoveries of these metals were markedly low (< 25 %). Overall, 177 and 644 kg H2SO4 /t dry ore were consumed at 70 and 95 oC, respectively. Activation energy of 79.0 ±1.0 kJ/mol was estimated for the mechanism of Ni and Co leaching and associated kinetics. Particles size analyses indicated that when the breakage of frail laterite particles due to shear is taken into consideration, differences in feed and leached product particle size distributions were insignificant , despite a remarkable increase in BET specific surface area of the product. Mineralogical analyses of the feed ore and leached solid products revealed a sub-crystalline silica phase enrichment of the latter. The overall results suggest that the mechanism of acid leaching of saprolitic Ni laterite may be described by a chemical reaction-controlled, shrinking core model."

Jan 1, 2014

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci

"An interesting occurrence of gold bearing ores of economic interest has recently been discovered in the Serrenti- Furtei district, central-southern Sardinia (Italy). The upper part of the orebodies are leaner and fairly porous, and are undergoing intense oxidation processes. In the lower parts sulphide ores predominate, chiefly enargite-luzonite and pyrite and these have a more compact structure. The passage from the oxidized to the sulphide zones, is rather irregular and difficult to delineate. The gold, generally occurring in its native form, is found in small grains. Mineral reserves in the area concerned were originally estimated to total 2.77 Mt: 0.63 Mt of oxide minerals with average gold content of 2.75 g/t and 2.14 Mt of sulphide ores with average gold grade of 3.18 g/t.Recovery of the valuable metals is a complex problem.The effectiveness of a variety of gold extraction techniques has been evaluated conducting tests on batches of ore representative of the different orebody depths obtained from core samples.The techniques investigated were: heap and vat leaching; flotation and flotation followed by leaching of the flotation tailings. The findings indicate that:• the gold contained in the ores in the upper oxidized zones of the deposit can be efficiently recovered by direct cyanidation via heap or vat leaching;• the sulphide ores in the deeper portions, that are not amenable to direct cyanidation but contain enargite concentrations of potential economic interest can be processed by means of flotation to produce a gold/copper bulk concentrate;• beneficiation of the difficult-to-treat minerals contained in the transition zone requires some knowledge of their intrinsic properties. A distinction should be made between the ores containing minor amounts of enargite which appear to be amenable to vat leaching and those with relatively higher enargite content which are processed using bulk flotation of the gold and copper minerals followed by vat leaching of the resultant tailings."

Jan 1, 2003

By H. Matsuoka, M. Kawata, K. Haga, K. Mitsuhashi, C. Tokoro, A. Shibayama, R. Kawarabuki

"The mineral surface characteristic is important for the flotation because it affects the flotation behavior of the mineral. Conventionally, in the flotation process for Cu sulphide ores, the degree of ore floatabilities varies depending on the mineral phase such as chalcopyrite, bornite, or chalcocite. Therefore, mineral surfaces are treated with activators and depressants to control the floatability of target minerals and obtain high recovery performance. There are lots of flotation reagents which have many effects on ores depending on ore characteristics and conditioning methods. For example, sodium hydrosulphide (NaHS) as activator is known to have the effect of resulfurizing and activating oxidized surface of chalcocite and bornite. On the other hand, NaHS is reported to depress chalcopyrite floatability. In this study, the evaluation of mineral surfaces was conducted to predict flotation behavior. Activation of Cu minerals (chalcocite, bornite, and chalcopyrite) by NaHS was experimented. The three Cu minerals were treated in two steps. Firstly, they were oxidized in the drying oven. Secondly, they were treated with NaHS solution. After each treatment step, each mineral was measured by contact angle apparatus then analyzed by X-ray photoelectron spectroscopy (XPS). The results of surface characteristics after oxidation and NaHS treatment were utilized to accomplish the study’s objective. INTRODUCTIONCopper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are well-known abundant copper-containing minerals. Generally, these minerals are recovered and concentrated via collector flotation. In flotation, the wettability of the mineral surface is an important factor in its recovery. When the surface is hydrophobic, the mineral has high floatability and when the surface is hydrophilic, it has low floatability. Usually, Cu sulfide minerals have high floatability. However when their surfaces are oxidized, their floatability becomes lower in flotation. In this case of surface oxidation occurrence, activators are added before flotation to modify the surface property of the Cu sulfide minerals so that they can be floated at a certain flotation condition. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao et al. (2018) reported that NaHS is often used as sulfurizer for oxidized sulfide minerals (Becker et al., 2014, Clark et al., 2000, Newell et al., 2006, 2007, Newell and Bradshaw, 2007). Although the floatability of Cu sulfide minerals was raised by adding NaHS generally, the results of this flotation study showed that the flotation behaviors of mixed chalcocite, bornite, and chalcopyrite were different. Therefore, it was considered that NaHS works differently for each mineral."

Jan 1, 2018

By Peter Ay, Matthias Schmidt, Christian Stollberg

"The aim of the study is the development of a seamless reprocessing procedure for plastics from automotive parts which are to be recycled (figure 1). Before automatic sorting can be performed, the materials first have to be identified by a near and middle infrared (NIR/MIR) system.Materials reprocessing basically includes research on size reduction, decoating, and roughening of the materials. Variants of the necessary technologies such as different shredders and mills and physico-chemical or mechanical decoating and roughening procedures together with the fundamental approaches underlying these methods are investigated and benchmarked. This allows the theoretical determination of the impact of each method not only on the overall process but also on the result achieved within the identification and sorting procedures."

Jan 1, 2003

By T. Damyanov

Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. A modelling simulation study of the behavior of two grinding media in the grinding process was conducted to determine the possible advantages of the new shape milling bodies called tetraballpebs. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. A three dimensional CAD model of the mill drum with a diameter of 1200 mm was used. A continuous operating mode was simulated in terms of the 3D contact elements of the model (milling bodies and mill drum). Simulation tests were carried out in a typical grinding mode and at a typical rotational speed of the drum mill (75 per cent of the critical speed in cataracting mode). Studies carried out with both grinding media include equal number of milling bodies with the same weight and volume. Having thus ensured a uniform mass of the grinding media and same number of milling bodies, and constant other conditions and process parameters, conclusions can be drawn about the influence of the shape of the milling bodies on the grinding process. A kinematic analysis of the system using CAE (computer-aided engineering) model parameterization was conducted. The controlled parameters are: ? Power draw; ? Kinetic energy of each milling body; ? Motion of milling bodies inside the drum Keywords: grinding, grinding simulation, balls, tetraballpebs, DEM, CAD-CAE

Sep 1, 2012

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By Zhiyong Gao, Ruiying Fan

"Crushing and grinding are the prerequisite processes in many industries, such as minerals processing and powder technology. During crushing and grinding, minerals will cleave or fracture along the directions by broken the interlayer bonds (e.g., ionic bonds), generating some commonly exposed surfaces. The broken (or dangling) bonds at the generated surface makes the surface more active and determine the reactivity of the surface. In this work, the population of broken (or dangling) bonds on commonly exposed surfaces of fluorite mineral (a chosen model mineral) was calculated. Based on the calculated broken bonds information, the anisotropic surface reactivity of fluorite such as surface energy, surface relaxation, dissolution, wettability, surface charge and adsorbability, were discussed. The results show that the surface broken bonds density, which is positively related to the surface energy, can be used to predict the cleavage nature, surface relaxation degree and surface stability of fluorite crystal. The distribution characteristic and the number of broken (or unsaturated) bonds of surface active atoms (like Ca for fluorite crystal) can be used to predict and explain the anisotropic wettability, surface charge and adsorption mode and strength of organic molecules on different commonly exposed surfaces. It is easy to conclude that the calculation of surface broken bonds can serve as a fast and accurate way to start the mineral chemistry studies. These findings will be helpful to the mineral/material chemistry research in related interfacial science communities.INTRODUCTIONGrinding for mineral liberation is a prerequisite for a successful flotation separation. Also grinding for size reduction is a prior process for a favorable powder technology. During the grinding process, the minerals / materials will cleave and fracture along certain crystal directions with relatively weak interlayer chemical bonds1 to form a number of common exposed surfaces. Exposed surfaces are the outer boundary of a solid substance. In the mineral / material block, the bonding orbital of the atoms is filled with electrons and the atoms are in a steady state. Atoms on these exposed surfaces appear to show dangling bonds (or broken bonds) by losing chemical bonds to adjacent atoms in the previous block. Therefore, surface broken bonds serves as an initial property of a fresh surface. The lattice arrangement and crystal orientations causes differences in the number of dangling bonds on each exposed surface, i.e., anisotropic surface broken bonds2. The anisotropic dangling bonds enable the exposed surfaces to show varying degrees of surface reactivity (including surface energy, surface charge, surface relaxation, dissolution, wettability and adsorption behavior), known as anisotropic surface reactivity."

Jan 1, 2018

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By Liu Fan, Shang Yanbo, Wang Zhongming

"Besides valuable metals of Cu, Sn, WO3, Zn, there are S, Ag, CaF2, In and so on in a complex ore deposit in south China (which belongs to Hu Nan Shizhuyuan Non-ferrous Metal Limited Liability). Although it proved reserve amounts to 3.5×107 ton, its crystal character limits its utilization in large-scale. It features complex relationships between valuable minerals, finest crystallized particle size, low-graded valuable metals (Cu 0.30%, Zn 0.5-0.7%, Sn 0.2%, W<0.1%). If only tungsten minerals are considered, it means WO3 grade is too low (the cut-off grade of WO3 is 0.1% in China). Only Cu and Sn minerals are recovered from 2006 and Cu recovery is less than 70%, Sn 15-20%. Other valuable metals of W, Zn, S and CaF2 were lost in the tailings. To make good use of the ore, the technology of fully recovering Cu, Sn, W, Zn, CaF2 and rare metals are in urgent need. After systematic researches, the flow sheet of "bulk flotation of Cu-Zn minerals at first, then Cu-Zn separation, then recovering sulphide by flotation, then recovering iron minerals by magnetic separation, then bulk flotation of Sn-W minerals after desliming" is developed. Furthermore, specific Sn-W collectors of BK411 and BK412 are applied into the processes and better indexes are obtained. The industrial indexes are listed as followings: the content of Cu, Zn, Sn, WO3 of ROM ore is 0.31%, 0.65%, 0.13%, 0.03%; Cu and Zn recovery are 82.23% and 37.79% respectively; 63.76% of Sn and 34.34% of WO3 go into the Sn-W bulk concentrates. Economic benefits are remarkable."

Jan 1, 2014

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management."

Jan 1, 2003

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 – 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By H. Q. Peng

The study of synergistic reagents combination of mineral floatation is more and more important with the decreasing of bonanzas now. In order to determine the chemical reaction mechanism, here we present the synergistic reagents combination: amyl-xanthate, butyl-dithiophosphate and N,N-diethyldithiocarbamate ester, which dissolved by different organic solvents. The reagents were applied by an Anhui mine to float low-grade covellite as a substitute for ethyl-xanthate. One reaction products Na2HPSO3?5H2O (disodium hydrogen-thiophosphate pentahydrate) which was re-crystalized and measured by X-ray diffraction analysis. In its crystal structure, the two crystallo-graphically different Na ions are six-coordinated and are bridged by two covalent bonds with the O atoms of water molecules to give a basket unit. However, we can?t get Na2HPSO3?5 H2O by combining butyl-dithiophosphate and N,N-diethyldithiocarbamate ester under the same condition. This discovery may provides a intuitionistic evidence that in the process of reaction, the three com-pounds would cooperate with each other, but the decisive reaction may be the hydrolyzation of amyl-xanthate.

Jan 1, 2014