Search Documents

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By Mikhail I. Khersonskaya, Mark I. Mantsevich, Andrey V. Tarasov

"Due to depletion of the existing ore deposits the content of non-ferrous metals in produced ores has an inevitable tendency to decrease. Processing of low-grade ores is associated with production of low-grade selective concentrates and poses serious problems for the non-ferrous industry relating to increasing losses and expenses for waste treatment and disposal.The main component contaminating selective concentrates is iron sulphides.Copper-nickel, copper-zinc and polymetallic ores have been discussed as most important types of ores requiring removal of iron sulphides.One of the promising directions for development of selective flotation technology is the use of lowmolecular organic depressors. An advantage of organic compounds is in the possibility of multi-variant structure of organic molecules, which permits selection of a most efficient reagent for the given conditions. Another way for improving the grades of concentrates is concentration of valuable constituents associated with iron sulphides in an intermediate product and upgrading of the latter by chemical and metallurgical techniques.In order to remove iron from nickel concentrates, specific process conditions have been developed for selective flotation of pentlandite with the use of an organic depressor for pyrrhotite. The use of a depressor for flotation of high-grade copper-nickel ores ensures an increase in the nickel content up to 14% in the nickel concentrate produced as compared with 7% when using conventional process conditions, along with a nickel recovery improved by 2-3%."

Jan 1, 2003

In this paper, various methods, such as XPS, XRD, SEM and zeta potential measurement are applied to investigate the action mechanism of sodium sulfide in flotation of lead and zinc oxysalt minerals. The experimental results show that the mechanisms of sodium sulfide in flotation of lead oxysalt minerals and zinc oxysalt minerals are different: on the surface of cerusite, there is lead sulfide phase formed under the reaction of sodium sulfide, resulting that the cerusite surface shows the form of galena, which is advantageous to the adsorption of anion collector and improves the floatability of cerusite as a result. On the surface of zinc oxysalt minerals, there is no zinc sulfide phase formed, but the sodium sulfide increases its surface electronegativity, and enhances the adsorption of cation collector lauryl amine, so the floatability of zinc oxysalt minerals is improved. The difference of action mechanisms of sodium sulfide on lead and zinc oxysalt minerals exactly explains the reason why different collectors are selected in the flotation of cerusite and smithsonite, which are both carbonate minerals although.

Jan 1, 2014

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work. • Effective Experimental ValidationAn automated 3D tracking technique is employed to study the motion of plastic particles deep within the charge of a 142mm diameter experimental mill. A Biplanar Angioscope is used to film the mill with X-rays in two planes simultaneously at 50 frames/s, with a shutter speed of 1/3000s. A marked ball within the charge is tracked for over 2 minutes and the resulting digital images processed by a fully automated imaging technique, which locates the 3D coordinates of the particles to within 0.2mm. With over 250 circulations, this provides statistically rigorous and accurate data for verification in the numerical modelling of mills.A series of validation techniques have been developed to compare the experimental trajectory data with the outputs of both 2D and 3D DEM simulations. The techniques describe the shape of the charge and the particle motion within mill, allowing objective comparisons to be made of key features of the charge, such as the equilibrium surface and the centre-of-circulation."

Jan 1, 2003

By G. P. Wong

"In the Inco matte separation process, a slow-cooled converter matte is separated into three main discrete mineral phases: chalcocite (Cc), heazlewoodite (Hz) and a Cu-Ni-Fe alloy. After magnetic removal of the alloy, Cc and Hz are separated by flotation at pH>12 with diphenyl guanidine (DPG) as both collector and frother. High selectivity is achieved in rougher flotation. However, in later flotation stages such as in the middlings circuit, as oxidation takes place, Hz becomes highly floatable, resulting in a very poor separation between Cc and Hz.Starch and dextrin as Hz depressants were evaluated on the middlings circuit feed and showed no positive impact on Cc/Hz separation selectivity. Ethylene diamine tetra-acetic acid (EDTA) extraction showed the existence of abundant surface Cu and Ni ions. The use of triethylene triamine (TETA) or EDTA in flotation did not improve Cc/Hz separation selectivity. Microflotation tests were carried out on pure synthetic Cc and Hz minerals. It was found that Hz did not float in the presence of DPG. However, Hz conditioned with either copper sulfate solution or in contact with Cc floated readily in the presence of DPG. It is concluded that the major reason for Hz flotation in the middlings circuit is due to Cc oxidation releasing Cu ions that adsorb on the Hz surface making it reactive with DPG thus rendering the Hz floatable."

Jan 1, 2003

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

A new flotation system has been developed to improve the generally slow separating differentials of fine bubbles and fine particle suspensions. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. In the new system (see figure 1) this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.

Jan 1, 2003

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By W. Fander, Zhonghan Zhang, T. Choo, J. Enraght-Moony

"This paper describes the mineralogical and metallurgical procedures used to determine the recovery and concentrate grade of heavy oxide minerals occurring in lode deposits. The data produced also provide vital information to the processing engineers, which allows them to develop the most suitable flow sheet for that particular heavy mineral, here called an Economic Oxide Mineral (EOM). It demonstrates how results are interpreted to ensure that the proper process is used at each treatment stage to optimise recovery and to produce the most suitable concentrate at that point. Reference is made to some of the current equipment and techniques that can be used to process EOMs. The paper shows that when assessing the economic potential of a new ore body, or existing ore treatment plant, ore characterisation (OC) is necessary. This is especially true for EOMs such as cassiterite (SnO2), wolframite ((Fe, Mn, WO4,) pyrochlore ((Na,Ca)2Nb2O6(OH,F)), and tantalite (MnTa2O6) where often what seem to be small changes in ore types can have major effects on recovery and concentrate grade. Due to advances in flotation technology scheelite (CaWO4) in some deposits can be less vulnerable to OC variability than other EOM’s. Thorough mineralogical examination is shown to be the fundamental basis of correctly undertaking OC. This is because mineralogical analysis identifies each of the steps required to ensure that all ore types and zones are recognised, and differences explained, and shows the benefit in using reference samples to compare differences in the ores. The OC methods used for EOMs containing metals such as tantalum, tin, tungsten and niobium are similar; if two or more of these EOMs occur in one deposit as separate minerals, then OC will show when and how these minerals should be separated. The OC techniques described for EOMs can also be tailored for other heavy minerals, precious metals and graphite."

Jan 1, 2014

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"In Russia the industrial exploitation of ore deposits is determined as a strategic direction of gold extraction industry development. The majority of gold-containing ores of Russia is referred to category of rebellious ores with 3-5 g/t gold content and is characterized by low factors of gold and silver extraction under cyaniding. The resistance of goldcontaining raw materials under their processing is caused by presence of very fine gold particles less than 0,1-0,01 µm in size, associated with the pyrite and arsenopyrite. Significance of the problem of rational rebellious ores beneficiation and high precious metals extraction is increasing from year to year.Group of scientists from IPKON and IRE, Russian Academy of Sciences, has developed highly effective, powereconomic and ecologically clean method of breaking-up of resistant gold-containing ores and their beneficiation products on the base of using an energy of powerful electromagnetic pulses. For the first time there have been designed laboratory installation for resistant raw materials treatment in dry and wet state (solid/liquid ratio = 5:1) and ground material less than 1-0,5 mm.Mechanisms of powerful electromagnetic pulses action on natural mineral components, including dielectrics (quartz, calcite), semiconductors (sulfides) and metals (gold, silver) have been theoretically accounted. Pulses action parameters and ways of pulses generating have been discussed in different conditions. At tension of electromagnetic field, exceeding the electric strength of processing material, an electric breakdown develops in the mineral matrix of sulfides and dielectrics. Under the series of pulses action the forming of plural breakdown channels occurs, leading to strength loss of material and microcrackes developing. Thus, the action makes it possible for leaching solution to access precious metals particles under cyaniding process. Distinctive changing of pyrite and arsenopyrite surface structures under the influence of powerful electromagnetic pulses is confirmed by studies using optical and scanning electron microscopy."

Jan 1, 2003

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By R. C. Miranda

This paper intends to demonstrate the applicability of tools for advanced process control and online particle size image analysis in crushing and autogenous grinding circuits. In a crushing plant, cameras are installed in the conveyor belts of the circuit products. The vision system continuously processes the acquired images and thus obtains the variation of the size distribution curve. From these measurements, the advanced control system can operate, for example, at the opening of the crusher, in order to keep the P80 in the desired range. In addition, through the power information and level of the crusher's chamber, it is possible to increase the capacity of the crushing circuit. If the crusher is not equipped with an automatic opening adjustment, a warning may be issued to the operator to provide this setting manually. In mineral processes that use autogenous and semi-autogenous grinding for fragmentation, obtaining online F80 through the vision system allows for manipulating the parameters of rotation speed and solids concentration, through which the amount of material at the critical particle size that is produced can be controlled. In addition, the noise produced in the mill can be measured and controlled. Thus, it is possible to prevent breaches and to optimise the mill capacity for grinding. Image analysis combined with an expert system that translates this information and acts to seek the most appropriate particle size distribution, brings greater stability to the process optimising the capacity of the equipment, which allows for significant gains in production.

Sep 1, 2012

By Yu. Gurevich, M. Teremova, I. Prokopev, A. Razvjaznaya, N. Algebraistova

"The objective of this work is the scientific justification and development of efficient and environmentally-friendly method of bulk concentrate preparation for selection with application of microbiological practices. This research suggests to apply Pseudomonas Japonica bacterial culture to the bulk concentrate before the selection circuit in order to clear the surface of sulphides from the xanthate skin. It is also suggested to apply bacterial consortium Ochrobactrum ?nthropi and Pseudomonas aeruginosa JCM 5962 for desorption of diesel residual concentrations. High-efficient and environmentally friendly method of copper-molybdene and lead-zinc bulk concentrate selection was developed based on theoretical and experimental research work with application of microbiological practices. In comparison with conventional methods (steaming, sodium sulphide washing) the above suggested bio-technological method of bulk concentrate preparation before selection cycle will allow to reduce material and power expenditures, and it is also environmentally friendly. INTRODUCTION High-efficient selection of sulphide bulk concentrate is gained exclusively after collecting agent is removed from mineral surface. Therefore, the problem of bulk concentrate preparing before the selection cycle is acute, since the further technological parameters of the subsequent separation depends on the effectiveness of pulp preparation. Existing traditional ways of bulk concentrate preparation. such as washing or steaming, are characterized by high energy and material costs in industrial conditions [1,2]. The microbiological treatment before separation of the bulk concentrate into different kind of concentrates appear one of perspective processes for treatment of bulk concentrates [3,4]. At the present time, the world practice of processing mineral raw materials demonstrates the wide application of technologies using microorganisms: bacterial leaching and oxidation, purification of industrial wastewater. This is due to the fact that biotechnological methods are environmentally safe, low-cost, and suitable for refining complex ores and raw materials of industrial origin."

Jan 1, 2018

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012