Search Documents

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

By N. Vorob?ev-Desyatovskii

The process of gold(I) adsorption on activated carbon (AC) from aqueous Na[Au(CN)2] and the state of the adsorbed gold cyanide complex on the adsorbent surface was investigated by photometry, XPS, XANES methods. By DFT method, quantum-chemical calculations were performed of the gold cyanide species on activated carbon surface. It was established that the binding of gold(I) with the surface of carbon involved several simultaneous processes governing the selective adsorption of gold(I) from the cyanide solutions.

Sep 1, 2012

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By G. H. Lind

The Minerals Tertiary Education Council (MTEC), over the past decade, has worked closely with Australian higher education partners in metallurgical education to build capacity in this discipline to deliver high quality graduates for the Australian minerals-industry. This paper explores the benefits of industry engagement through a national innovative collaboration, the Metallurgical Education Partnership (MEP), and specifically the final year Process Design Project (PDP), over the four year period from 2008-2011. Some of the benefits discussed in this paper include outcomes of the student experience during an industry-intensive workshop, collaboration between higher education providers and aligning graduate attributes to meet industry requirements.

Sep 1, 2012

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By C. A. Perez

Estimation of rock composition in mineral plants is important to determine rock size and grindability which in turn may improve control of the grinding process. Variations in ore grindability and size distribution directly affects mills power consumption and throughput. Therefore, it is desirable to develop new tools to estimate rock lithological composition. In this paper, a new method for lithological classification based on machine vision is proposed. The method is based on a single video camera and employs information about texture using several different spatial scales. Texture information is extracted from rock images using Gabor filters that can be adjusted at different spatial scales and orientations. After feature extraction, rock images are classified using support-vector machine (SVM). The method was tested on a database containing sub-images of 64x43 pixels of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets for training, cross validation, and for test. Classification accuracy is compared with previously published results on a dataset with three different classes of rocks according to their hardness. Results show that our proposed method reached significant improvements (between 13%-20%) in classification accuracy relative to previously published results. Keywords: rock classification, lithological classification, grindability estimation, Gabor feature extraction, texture features

Sep 1, 2012

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By Kari Niiranen

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. The largest of the apatite magnetite deposits and the mines are Kiirunavaara with annual production rate of approximately 27 Mt crude ore underground. LKAB produces two varieties of pellets: blast furnace pellets and direct reduction pellets (LKAB DR Oxide Pellets). Meanwhile the concentration process in a sequence of the low intensity magnetic separation (LIMS) and flotation at the concentration plant. In spring 2007 there were noticed great fluctuations of SiO2 grade in the crude ore. The high SiO2 grade is particularly problematic in the case of direct reduction pellets. In consequence, a project was started (called Silica in the Mine) to define exactly the problem related with silica and to find out, if possible, the reason for the great fluctuation of SiO2 grade in the crude ore going to the processing plant. A further target of this project was to develop a simplified method at the laboratory scale, to predict SiO2 grade in the magnetite concentrate in the future, but also predict the physical properties of the ore with respect to mineral processing. The essential stage of systematic characterization of the ore body for mineral processing properties is the estimation and simulation of different parameters from the laboratory scale to the large scale at the concentration plants using empirical data collected at the mineral processing by LKAB in Kiruna. Further a target was also to find useful physical parameters for mineral processing and implant those parameters into the existing geological 3D-model of the deposit. This information will be used for making prognosis of the future mining and the quality of the crude ore. It will also give better control and improve the production planning in the mine and the performance at the concentration plant in Kiruna concerning the decrease of the SiO2 grade of the magnetite concentrate.

Sep 1, 2012

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014

By Peter M. Solozhenkin

Considering the main idea of the paper, namely that the interaction energy of reagents serves as a criterion used for their selection, as well as due to their insufficient study, the authors have therefore considered studying the aspects of computer modelling and molecular dynamics of largely used collectors for the flotation of nonferrous and precious metal ores. Three-dimensional molecular models for sulphydric reagents have been created, studying as well the distribution of the partial charges on their atoms. It has been shown that the value of the partial charge on the phosphorus atom in diethyldithiophosphinate and diethylmonothiophosphinate is high positive. The value of the partial charge of the sulphur atom is negative, strengthening its bond with the metal cations from the mineral surface. The molecular orbitals for the sulphydric reagents have been created determining as well the energy of their level. The computer modelling key parameters have therefore been defined. The new reagents have been tested for gold, copper and rhenium ore flotation. Gold recovery has increased with 4.2 - 4.7 %, copper recovery with 3.3 % and rhenium recovery with 15.5 %. A number of new flotation reagents have been recommended, such as: diethyldithiophosphate, (C2H5)2NCH2CH2OC(S)SNa, (C4H9NH)2P (S)SNa and also (C2H5)2P(S)ONa and (C2H5)2 P(O)S Na. Keywords: flotation, molecular modeling, design, orbital?s

Sep 1, 2012

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By Jaeheon Lee, Jae-Chun Lee, Doyun Shin, Minseuk Kim, Hyunsik Park

"The appropriate treatment of cyanide waste water is becoming an emerging issue because of the toxic residue and large quantity produced from gold processing plants. In the present article, we designed and operated a continuous biological cyanide treatment system using domestic sewage sludge and various microorganisms including a cyanide-producing and degrading bacterium, Chromobacterium violaceum. The synthetic wastewater containing 50 mg/L of cyanide was pumped continuously into the reactor at a flow rate of 500 mL/d for 21 days. When 50 mg/L of cyanide was fed, the cyanide concentration in the effluent of the reactor inoculated with activated sludge (S-50) decreased by 7.5 mg/L in the effluent. The other reactors did not show significant cyanide degradation and the reactor inoculated with C. violaceum showed increased cyanide concentration in the effluent. The microbial community in the reactors was analyzed by 16S rRNA-gene based pyrosequencing technique to investigate microbial response to cyanide addition and operation time. The microbial community analysis shows that the phylum Proteobacteria was detected in the reactors showing significant cyanide degradation (S-50), while Firmicutes and Bacteroidetes was dominant in the other reactors with very low cyanide degradation. Proteobacteria could not compete when the other phyla Firmicutes or Bacteroidetes were inoculated. This study shows the feasibility of the biological cyanide treatment system for gold processing plants and contributes new fundamental knowledge about the microbial community in the biological cyanide treatment system. INTRODUCTION Cyanidation has been widely used to recover gold from ores or secondary resources since first proposed by MacArthur and Forrest in 1888 (MacArthur et al., 1888) and it is used in many states of the USA, including Nevada, Arizona, California, Colorado, and Idaho (Laitos, 2012). Cyanide compounds are highly toxic and create serious problems for wildlife and water management (Solomonson, 1981; Donato et al., 2007). Furthermore, because many countries have imposed strict standards for cyanide discharge (USEPA, 1985), it is essential to develop a cost-effective and environmentally friendly technology for treating cyanide-containing wastewater."

Jan 1, 2018

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012