Search Documents

Taknar polymetal (Cu-Zn-Au-Ag-Pb) deposit and concentration flotation plant are located in the northeast of Iran. The flotation feed contains Chalcopyrite, sphalerite and pyrite with 4, 4 and 8 percent respectively. Cu and Zn contents are 1.26 and 3.5 present. Pyrite decreases the quality of base metal concentrates and increases the amount of sulfur compounds produced in the base metal extraction processes. Therefore, depression of pyrite is essential in the concentration of base metal sulfides by flotation. For flotation tests, 4 mixed collector systems, MIBC (20g/t), lime and tow depression systems (sodium cyanide (60g/t)-zinc sulphate and dextrin (300g/t)-zinc sulphate) were used as collector, frother, pH regulator and pyrite-sphalerite depressants in the chalcopyrite flotation stage, respectively, and SIPX, MIBC, lime and copper sulphate (as activator) were used in sphalerite flotation from first stage tailings. The results have shown that, sodium cyanide is a suitable depressant for pyrite and sphalerite in the first stage of flotation. Compared to dextrin as depressant, chalcopyrite recovery was decreased approximately 1.83%. In addition, when sodium cyanide was used as pyrite depressant, copper sulphate consumption raised approximately 90 g/t for activation of sphalerite. From Environment and HSE points of view, dextrin is natural, biodegradable, and non-toxic while cyanide is very high toxic. Keywords: sequential flotation, Cu-Zn massive sulphide, pyrite depressant, dextrin, cyanide

Sep 1, 2012

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012

By P. K. Arya

Huge quantity of copper is lost in Crown, Sill, Rib Pillars, hanging wall, foot wall and unexploited ore bodies in several closed underground copper mines and old worked out stopes of Hindustan Copper Limited at Mosaboni and other places. These mines might have been uneconomical to work with conventional mining methods. However, huge quantity of mineral reserves is lost due to their closure. Chemical and in-situ bio-wash leaching, if tried can provide an answer to facilitate the recovery of metallic values economically. Encouraging results were obtained during an experiment at North Badia Mines at Mosabani in the past. Though the experiments were not completed but whatever results obtained were very encouraging and can be successfully tried to make it viable. The results of the experiments are discussed here and a plan is suggested to recover copper from such mines.

Jan 1, 2014

By Jacek Kolacz

A new sensor based sorting system related to complex image analysis has been developed at Comex AS - Norway. It makes it possible to separate different mineral particles regarding their color, shape, texture, size, density and indirectly their composition. The sorting system has been successfully tested and applied for sorting minerals providing high separation efficiency in the range of 95-99.9 %. The main advantage of this system is connected with its universality where many material parameters are analyzed in the same processing unit by a single passage.

Sep 1, 2012

By Yuhe Tang, Jun Zhang, Jianguo Liu

"The nature high carbon graphite with fine particle size has low commercial value because of its narrow application range. In order to improve its value, this paper has studied the methods for nature spherical graphite. The nature spherical graphite can be used as the battery material in the field of electronic product battery and new energy automobile battery, basis on the physicochemical characteristics and particle feature of graphite. In this research, the Fixed Carbon (FC) grade of the graphite sample is more than 95.0% and the particle size of the graphite sample is from +325 mesh to -100 mesh. There are many methods for nature spherical graphite, including the fluidized bed airflow mill, the hydro-spheroidization mill and micropowder mill. The testing results indicate that the method of ACM micropowder mill is the best because the spherical shaping ratio and production yield of spherical graphite are both the best.According to the testing results of the ACM micropowder mill, the best process includes two stages of coarse crushing, four stages of fine crushing and twelve stages of shaping. And two kinds of spherical graphite products can be got, which are the product of D50=22.85 µm and the product of D50=15.43µm, and the whole yield of them is up to 54.43%. So, it lays a foundation for the high value utilization of this kind of graphite resources.INTRODUCTION Graphite is isomer of the diamond. Graphite ore resources are mainly concentrated in China, Brazil, India, followed by Czech, Korea, Mexico, Canada and other countries. Graphite ore has lots of characteristics by itself crystal structure, such as good resistance to high temperature, electrical conductivity, thermal conductivity, thermal shock resistance, good lubricity, plasticity, chemical stability and so on. So, Graphite is widely used in metallurgy, machinery, electrical, chemical, petroleum, nuclear industry, defense industry and other areas. [1,2,3] Natural graphite ore has low geological Fixed Carbon (FC) grade. FC grade should be enriched to more than 94.0% by mineral processing. [1,2] The particle size composition of this high carbon graphite affects its application value. The part of +100 mesh particle size has high application value. The part of -100 mesh particle size has low value because of its limited application field. In order to improve the value of-100 mesh particle size, this part high carbon graphite can be made into spherical graphite. And the value of the spherical graphite is great, it is more than 8 times of the feed. This paper has lots of tests for spherical graphite preparing with the fine particle size natural high carbon graphite. And it lays a foundation for the high value of this kind of resource."

Jan 1, 2018

By Danilo Zim, Matheus Paschoalino, Denis Guimarães, Jasbir Gill

The shortage of water supply in some regions of the globe is particularly problematic and forces mining companies to adopt alternatives like pumping sea water from the ocean up to the mining sites. Although deaeration of sea water or the use of lined pipelines are known options to prevent corrosion during pumping, a recent development of a new corrosion inhibitor allowed the use of simple mild steel pipelines for this purpose. The objective of this study is to demonstrate the recent advances of this technology in protecting against not only general corrosion but localized corrosion, main cause of corrosion-related pipeline failures. Corrosion studies were carried out using electrochemical techniques, weight loss balance as well microscopy surface analysis in order to measure and therefore evaluate the treatment efficiency. The right dosage of corrosion inhibitors may vary depending on water composition and characteristics of each system. Differences were observed depending on the sea water source. Pretreatment of metallic surface impacts the observed corrosion rate which can be as low as 3.6 mpy. The absence of pitting or localized corrosion was achieved in aerated seawater.

Jan 1, 2014

By A. Muhammad, A. Abdelaal, M. EL Salmawy

"Energy is vital for economic growth and sustainable development. Greater efforts are being devoted to developing unconventional energy resources such as oil shale as an alternative promising source of oil or solid fuel supplement. The main object of this contribution is to determine the upgrade potential of El-Nakheil oil shale using froth flotation. Samples were prepared by comminution followed by sieving into different size fractions. The flotation behavior of the material and extent of cleaning was studied with respect to nonionic and ionic collectors of anionic and cationic types. It was found that the organic rich portions could not be rendered sufficiently hydrophobic by the used collectors and selectivity towards surfactant was very low."

Jan 1, 2014

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By S. Sheng, Y. G. Huang, W. Chai

"Polyacrylamide (PAM) is a typically synthetic depressant and may be used as a depressor of pyrite. The modification of polyacrylamide may improve its physicochemical properties and performances. Sulfonated polyacrylamides (SPAM) with different sulfonation degree (SD) were prepared using sodium sulfite as the sulfonating agent, and the interactions of SPAM and pyrite were investigated by the adsorption experiment in this work. The adsorption tests of SPAM on pyrite were conducted as a function of sulfonation degree, pH value and contact time. Pyrite and SPAM were constructed and optimized through MS software. The interaction mechanisms of sulfonated polyacrylamide and pyrite were simulated by molecular dynamics simulations. The results show that the adsorption capacities of SPAM at neutral and weak alkaline conditions are higher than that at acidic and strong basic conditions. The high sulfonation degree favors the adsorption of SPAM on pyrite surface. The adsorption process can be described best by the pseudo-second order kinetic model. Molecular dynamics simulations show that the adsorption of sulfonated polyacrylamide on pyrite is better than that of polyacrylamide. Sulfonated polyacrylamide can be used as a potential depressant of pyrite with the main interacting mechanism of hydrogenbond force.INTRODUCTIONPyrite is the most abundant sulfide mineral and often associated with valuable minerals such as galena, chalcopyrite, sphalerite, molybdenite, gold, diaspore as well as coal (Forrest et al., 2001; Jaiswal et al., 2015; Maier and Dobiáš, 1997; Qiu et al., 2017; Xin and Liye, 2010). Froth flotation is the most popular method to remove pyrite from valuable minerals. Pyrite could be floated as the flotation concentrate either by its hydrophobicity or activation by metal ions (Chandra and Gerson, 2009). What is more, pyrite could be seperated as flotation tailing by adding highly selective depressants including inorganic and organic modifiers. Polysaccharides polymers and lignosulfonate-based biopolymers are common natural organic depressants (Deng et al., 2017; Mu et al., 2016). While the synthetic organic products have proved to be particularly versatile in terms of molecule tailing capability and controlled structures (Boulton et al., 2001a; Raffa et al., 2015)."

Jan 1, 2018

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By S. V. Balikov

A close association of fine gold with pyrite and arsenopyrite is observed at many gold ore deposits. Gold forms and gold distribution in sulfides of different deposits were studied. A comprehensive method including optical spectrum analysis, X-ray diffraction analysis, high-temperature X-ray diffraction analysis, scanning electron microscopy and X-ray microanalysis was used for the de-tailed investigation of the defectiveness of the structure of pyrites from different deposits. It was shown that gold content in pyrites varied from 1.5 g/t to 100 g/t compared with 30 g/t to 230 g/t in arsenopyrites. The nature and arrangement of inner inclusions of foreign minerals in pyrites as well as occurrence of fractures and macro- and microdefects were examined. Iron, sulfur and arsenic contents in all pyrite samples were determined. Chemical composition of the detected inclusions was defined. Parameters of submicroscopic structure of pyrite were estimated using X-ray Fourier line shape analysis. Estimation of real structure characteristics with calculation of submicroscopic D-blocks and root-mean-square lattice deformation 2()evalues was performed. Defectiveness of the pyrite structure can be defined by the following parameters: K?1 and K?2 reflection resolution and its intensity within high Bragg angles; S content to Fe content ratio; the arsenic content and the local variation in its concentration within the pyrite grain; the size of submicroscopic blocks and the crystal lattice disturbance value. The performed analysis showed some relationships between these parameters and refractoriness of the pyrite concentrates. It was observed that at S/Fe ratio close to or higher than stoichiometry and at a low arsenic content (less than one per cent) pyrite concentrates were not refractory. The analysis results showed that concentrates of the Beryozovskaya gold plant (0.02~0.07 As%) and concentrates of the Kommunarovskaya gold plant (less than 0.05 As%) as well as some pyrites from the Sukhoi Log gold deposit had the same characteristics. It was found that average arsenic content did not excess 0.2 per cent. Arsenic distribution within the grain of all these pyrites was uniform. At S/Fe ratio lower than or close to stoichiometry and at high arsenic content (more than one per cent) and significant variation in its distribution within a pyrite grain the pyrite concentrates are refractory. Such pyrites are typical for the Sukhoi Log, the Bakyrchik and the Mardzhanbulak gold deposits. Direct correlation between arsenic and gold contents, in particular, in fine grains of pyrite was observed by many researches. This correlation was explained by impregnation of arsenopyrite which normally contains more gold than arsenic pyrites. The analyses results showed that no arsenopyrite impregnation was found: arsenic distribution within the grain was uniform but its concentration varied greatly. Such pyrite concentrates are more refractory. This paper presents the results of analyses of sulfides to determine the amenability of the associated gold recovery by hydro- and pyrometallurgy.

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By I. A. S. Brum

Brazil has large reserves of coal (7 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country's strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario, the processing of Brazilian coal in columns flotation appears as a promising alternative, having been successful in mineral systems containing fine particles. This paper aims to study the overall process of column flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dams. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The first results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. Concentrations of frother (pine oil) ranged from 50 g/t to 300 g/t and the collector (diesel oil) of 50 g/t to 200 g/t. Keywords: column flotation, coal, tailings, negative bias

Sep 1, 2012

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By D. Pirouzan

It is customary to use more than one stage of flotation to obtain an acceptable level of separation of valuables. Flotation circuit design is usually accomplished by applying empirical rules which usually results in operations not working at their optimum conditions. Given the capabilities of genetic algorithms (GA) in finding an optimum solution in a very disturbed search spaces, they can be used to obtain the desired flotation circuit configuration. In flotation circuit configuration and optimization problem, a combination of metallurgical parameters such as yield and concentrate ash content could be used as the fitness function for the genetic algorithm. The multi-objective nature of the problem justified to use Pareto method to arrive at a set of solutions. The appropriate configuration based on technical or economical considerations could then be chosen. To obtain the fitness function for any given configuration, it is necessary to model every flotation stage. The proposed method was used to find the optimum circuit configuration for a coal washing plant. The objective was to arrive at the highest yield while producing a concentrate with a certain ash content (< 11%). The feed to the flotation circuit was characterized based on the size fractions and their flotation rate constants. Results showed that with a 95% confidence, the absolute difference between the modeled and measured values were 2.9-5.5% for yield and 0.4-1.1% for concentrate ash content. When the proposed GA-based circuit configuration was implemented in the plant, the yield increased from the original value of 57.6% to 65.7% while producing concentrate ash content (10.9%) within acceptable limits. By adding one stage to the current three-stage circuit, it was predicted that the yield could further increase by 3.8% while keeping the quality of the concentrate within the appropriate level. Keywords: modeling, optimizing, flotation circuit configuration, genetic algorithms

Sep 1, 2012

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014