Search Documents

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By William Skinner, Jennifer MacCarthy, Jonas Addai-Mensah, Ataollah Nosrati

"Acid leaching in agitated tanks is central to hydrometallurgical processing for valuable metals’ (e.g., copper, gold, nickel and cobalt) recovery from low grade (e.g., < 2 wt.%) ores. In this study, atmospheric leaching behaviour of Australian saprolitic nickel (Ni) laterite ore using sulfuric acid was investigated under isothermal, batch conditions at pH 1. The effect of primary process variables comprising time (4 h) and temperature (70 and 95 oC) on the leaching mechanisms and kinetics was established for -2 mm, low grade (~1 % Ni) saprolitic ore dispersions at 40 wt.% solid loading. Leaching proceeded incongruently, reflecting the proliferation of gangue minerals’ constituent elements (e.g., Mg, Al, Fe) alongside Ni and Co in the pregnant leach solutions (PLS). Subsequent analysis showed that 89% Ni and 78% Co were extracted after 4 h at 95 oC whilst at 70 oC the recoveries of these metals were markedly low (< 25 %). Overall, 177 and 644 kg H2SO4 /t dry ore were consumed at 70 and 95 oC, respectively. Activation energy of 79.0 ±1.0 kJ/mol was estimated for the mechanism of Ni and Co leaching and associated kinetics. Particles size analyses indicated that when the breakage of frail laterite particles due to shear is taken into consideration, differences in feed and leached product particle size distributions were insignificant , despite a remarkable increase in BET specific surface area of the product. Mineralogical analyses of the feed ore and leached solid products revealed a sub-crystalline silica phase enrichment of the latter. The overall results suggest that the mechanism of acid leaching of saprolitic Ni laterite may be described by a chemical reaction-controlled, shrinking core model."

Jan 1, 2014

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By Xiaoping Xu, Tiansong Dong, Guosheng Wang

"Jianfengpo tin ore is located in Jiangxi Province, China. The cassiterite is fine and dispersed. It is hard to separate marmatite from a variety of sulfide minerals. Because the iron-containing sulfide minerals including pyrrhotite, pyrite and chalcopyrite are detrimental to the improvement of the grade of zinc concentrate. Besides, the presence of the iron oxides and ferro-carbonate minerals results in the difficult beneficiation of tin. Therefore, Jianfengpo tin ore is a kind of refractory cassiterite polymetallic sulfide ore. According to the properties of Jianfengpo tin ore, the technology process of "Sulphide ore preflotation-Bulk flotation of sulphur and zinc-Separation of sulphur and zinc -Magnetic separation-Gravity concentration" was developed to recover the valuable materials including marmatite, pyrite, magnetite, cassiterite and indium comprehensively. For the feed ore containing 0.87% Sn and 0.70% Zn, a zinc concentrate of 44.56% Zn with a recovery of 69.10%, a high-grade tin concentrate of 54.38% Sn with a recovery of 53.03% and a low-grade tin concentrate of 6.54% Sn with a recovery of 1.25% can be achieved in the batch flotation tests. In the industrial tests, for the feeding which contains 0.55% Sn and 0.65% Zn, the tin concentrate of 49.10% Sn with a recovery of 48.52% as well as the zinc concentrate of 45.11% Zn with a recovery of 60.10% can be produced. Thus some pyrite and magnetite concentrate are recovered as well. So Zinc, tin, sulphur and iron ores are recovered effectively by the technology."

Jan 1, 2014

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, S. Aliferova, T. Gurkova, T. Chumakova

Cationic flotation using alkylamines and their derivatives as collectors, and characterized by high selectivity of mineral particle separation, is finding ever growing industrial application. In recent years the industrial application has been initiated of new cationic collectors - alkylmorpholines. Efficiency of cationic surfactants operation as collectors is dependent upon their colloid and sorption properties and the availability of silicate .carbonate rock-forming mineral impurities in the ore, which sorb the cationic collector. Investigations have been carried out on the influence of frothers and organic depressors with various compositions upon physical-chemical and flotation properties of alkylamines and alkylmorpholines. On the basis of these investigations requirements for organic depressor were developed and new flotation reagents were proposed (V-1 frother and KS-MF depressor). The use of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles. Data of new reagents industrial application is presented. The reagents developed can be used for flotation processing of other ores.

Jan 1, 2003

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini, M. Zare

Difference between plant feed specifications in practice and design feed is a problem that most of processing plants face during operating and commissioning. This topic has led to inappropriate operating and necessitates repeating the basic tests on new feed. Gol-E-Gohar fourth concentrate line with a capacity of 2 MTPY, located in Kerman province, is the first iron concentrate plant in Iran in which High Pressure Grinding Roll (HPGR) technology has been applied. Plant&apos;s feed consists of 30% AG mills pebbles of lines 1-3 and 70% run of mine crushed ore whose Fe=51%, Fe/FeO=2.5, S=1.7% and work index=15 kWh/t. Desired concentrate has Fe>68% and S<0.7%. After the plant construction and operation commencement, providing design feed was not possible due to the crushing unit`s not being complete, therefore the plant was fed by AG mills pebbles. For predicting optimal conditions of the plant and investigating the possibility of improving the current concentrate specifications, sampling from the new feed and laboratory and pilot tests was performed again. Studies showed that new feed has Fe=41%, Fe/FeO=3.5, work index=17 kWh/t. Results of laboratory tests with Davis tube device and pilot tests run using magnetic separators with simulating the plant`s circuit showed that with current feed, achievable recovery in industrial scale would be 75.52% which compared to plant&apos;s recovery in studied period (75.94%) shows that plant operated in optimal conditions. To improve the current concentrate specifications (Fe=66%, S=1.03%, Ferec=75.94%) and for achieving desired concentrate, samples were reground to four fractions with k100= 300, 212, 100, 45 and Davis tube tests were performed on each of the samples separately. Results showed that the fraction whose k100=212 µm or k80=200 µm has respective Fe and S grades of 68.27% and 0.681% which are consistent with the desired concentrate.

Jan 1, 2014

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

By Isaak I. Maksimov, Tatyana E. Koltunova, Mikhail F. Yemelyanov, Liudmila A. Otrozhdyonnova

"INTRODUCTIONMetals losses amount up to 50% in coarse fractions in (>100 µm) and composite particles, and to 20- 25% in fine fractions (<10 µm) at non-ferrous floatation concentrating plants of the CIS. Therefore, reduction of metals losses in difficult fractions is of high significance.IMPROVEMENT OF FLOATABILITY OF COARSE AND COMPOSITE PARTICLESReagent regimes with application of strong collectors – xanthates ?5-?8, combination of butyl xanthates and aerofloats ?10-?12, butyl xanthates with hydrocarbons are proposed for this purpose. Application of such reagent regimes for copper and copper-molybdenum ores permitted to increase copper and molybdenum recovery by 0.5-3.9%.Studies, performed by means of specially designed non-frothing flotation machine with independently controlled agitation intensity and narrow size-ranges of air bubbles, established that the best results are achieved with employment of bubbles of 0.5-0.8 mm size regarding particles of any size, with small amounts of up to 2 mm size “transport” bubbles to be expediently used for floatation of coarse particles.Energy dissipation in the main volume of floatation cells must be lower than 0.2-0.25 m2/s3.Performed experiments permitted to formulate requirements to development of machine for floatation of coarse and composite particles. Such floatation machine with volume of 8.5 m3 provided for weak agitation in the main volume of floatation cell and uniform distribution of coarse particles throughout the depth owing to establishing of pulp circulation with upward flows. In addition, in the upper part of floatation cell where agitation is considerably weaker, favorable conditions are created for attachment of particles to bubbles. Testing of this floatation machine demonstrated a 7.5% increase in recovery of +0.2 mm particles in pyrite floatation and a 12-14% increase in recovery of +0.2 mm particles in apatite floatation as compared with a reference floatation machine."

Jan 1, 2003

By V. Avzian Belozersky reg 453524, Vasily V. Lodeischikov, Adolf F. Panchenko, Til E. Vidusov, Olga D. Khmelnitskaya, Vladimir E. Dementyev

"Presently, there is a number of gold deposits which cannot be developed using the conventional technologies with acceptable economic indices due to low gold content, high depth of ore occurence and other conditions. For such ores, an innovation technology of underground gold leaching in the place of their occurrence is of special interest. The technology excludes ore mining and hoisting to the surface. This enables the production cost of 1 g of gold to be considerably reduced in comparison with conventional methods of gold recovery.The Maminskoye deposit oxidized ores were chosen as the subject of underground leaching because they are ideally suited for this purpose due to their composition and hydrological parameters. The ore reserves within the underground leaching block are 90, 000 t with 0.7 g/t average gold grade.An experimental system for underground leaching with a throughput of 15 cubic m solutions per hour was developed. A combined filtration-and-infiltration system of the ore massif development by holedrillingwhere pregnant solutions are air-lifted was worked out.The underground leaching flowsheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution onto active carbon, carbon concentrate ashing and calcine melting to produce Dore metal."

Jan 1, 2003

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003