Search Documents

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By Leopoldo Gutierrez, Esau Arinaitwe, Marek Pawlik

"The effect of various polymers, including: anionic carboxymethyl cellulose (CMC), polystyrene sulfonate (PSS), humic acids (HA) and non-ionic hydroxypropyl cellulose, on the wettability of Athabasca bitumen was evaluated through dynamic contact angle measurements using the captive bubble technique. The tests were carried out as a function of pH at a constant ionic strength (0.01 mol/L sodium chloride). The evolution of the three-phase contact angle between the solution, bitumen and an air bubble was followed as a function of time over a period of ~6 minutes. The contact angle data were modelled using a first-order kinetic equation. The results were analyzed in terms of the initial contact angle, the evolution rate constant, and the steady-state contact angle value. In the case of anionic polymers, a pronounced decrease in the initial contact angle value was observed at pH 3. Under acidic conditions, there was no significant effect of CMC observed on the steady-state contact angle value but PSS and HA significantly decreased the steady-state contact angle value. At pH 8.5. the anionic polymers did not affect the wettability of the bitumen surface but they significantly decreased the contact angle evolution rate. These results suggested that CMC is not capable of permanently lowering the hydrophobicity of bitumen, and the polymer only slowed down the evolution of the contact angle to the steady-state value. The results also showed that polystyrene sulfonate and humic acids were capable of making bitumen hydrophilic but only under acidic conditions. Only hydroxypropyl cellulose (HPC) produced a large decrease in the steady-state contact angle under alkaline conditions (pH 8.5). The kinetics of contact angle evolution in the presence of HPC was also drastically lowered. The results were discussed in terms of the chemical composition of the polymers and their different affinities towards the bitumen surface."

Jan 1, 2014

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By Stefan Mutz, Thomas Pretz, Jörg Julius, Frank Hilbk-Kortenbruck, Aachen, Hartmut Harbeck

"The annual global production of primary aluminium was about 22 million tons in the year 2000. This represents the second largest production rate in the world market after steel. Experts are predicting that the global demand for aluminium will rise in the near future.In contrast to other metals such as copper, the recycling of aluminium is considered relatively difficult. There are two main alloying groups, namely cast and wrought. In the case of aluminium it is important that the constituents within the scrap aluminium to be smelted are clearly identified. Within the secondary remelting process alloying does take place, but a removal of unwanted metal constituents is problematic. Therefore mixed aluminium scrap (not genuine in-house collected material) can only be used to produce cast aluminium. Thus, in other words a down-cycling of wrought (extrusions and rolled) products occurs. However, in spite of these difficulties there is an increasing trend to produce aluminium from secondary scrap (approx. 35% in Germany). Similar trends have been identified in the USA and other industrialised countries. This development is mainly caused by the high energy consumption for the production of aluminium from bauxite. Producing aluminium from scrap is saving about 95 % of the energy in comparison to the processing of primary raw materials.An improvement in sorting technology is necessary to separate wrought and cast alloys of aluminium as the absolute amount of recovery from old scrap is higher than the demand for cast.This contribution presents some alternative methods, utilizing automatic picking technologies, which will be used to separate secondary aluminium in the future. During the recent years, some major progresses have been made in automatic picking technologies for different applications in the processing of primary and secondary materials.For the sorting of aluminium scrap a special additional sensor will be necessary. The best detection will ultimately be based on online elemental analysis of single particles. First investigations in the field of laser based systems for these applications have already been performed several years ago. One of the laser based techniques is the laserinduced breakdown spectrometry (LIBS)."

Jan 1, 2003

By D. Moradkhani

The objective of this research was, to evaluate the hazard of heavy metals in the soil around the National Iranian Lead & Zinc (NILZ) Company. In this study, 38 samples of soil around the NILZ factory were collected using standard sampling method, so that, the heavy metals Pb, Zn, Cd and Cr have been evaluated. The concentration of heavy metals were measured and compared with standard limits. The results show that the hazard of heavy metals in soil is not so serious and the content of Pb in just 5 percent of samples, and the content of Zn in just 3 percent of samples were above standard limits and the concentration of Cd and Cr were under the standard limits. Average, variance and standard deviation of the elements are calculated and with due attention to the standard deviation, Pb and Zn are seen to be more distributed than Cd and Cr. Also the isograde curve of heavy metals was drawn using software called Surfer. These curves showed that the heavy metals are concentrated at particular distances from the factory. Keywords: heavy metals, remote sensing, sampling method, isograde curve, Surfer software

Sep 1, 2012

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By Alexander V. Epiforov, Stanislav V. Balikov

This paper describes of processing tests of 8 flotation concentrates containing precious and base metals by pressure oxidation (POX) method. Concentrates 1 and 2 were gold-copper concentrates. Zinc and silver were by-products in these concentrates. These concentrates were processed by POX with following cyanidation of POX solid residues, copper solvent extraction and zinc carbonate precipitation. The recoveries of gold, copper, silver and zinc from these concentrate were 98, 99, 30 and 99%, respectively. Concentrates 3 and 4 were lead-zinc concentrates. Silver was by-product in concentrate 3. Gold, silver and copper were by-products in concentrate 4. Concentrate 3 was processed by POX with following reduction smelting of POX cakes for primary lead recovery and zinc carbonate precipitation from POX solution. The recoveries of lead and silver into ingot were 96 and 98%, respectively. The recovery of zinc was 99%. Concentrate 4 was processed by POX with following zinc carbonate precipitation and reduction smelting of POX cakes. Copper was precipitated from the POX solution using sodium sulphide prior zinc precipitation. The recovery of zinc into carbonate concentrate was 99%. The recoveries of lead, gold and silver into lead bullion were 95, 99 and 98% respectively. The recovery of copper into sulphide concentrate was 99%. Concentrate 5 was gold-pyrite concentrate, and concentrates 6-8 were double refractory gold-arsenopyrite concentrates. Silver was by-product in these concentrates. These concentrates processed by POX and CIL. The recovery of gold from concentrate 5 was 98%, and from concentrates 6-8 was 85-90. Low gold recovery from concentrates 6-8 was associated with preg-robbing factor. The recovery of silver from gold-sulphide concentrates did not exceed 10-20%. The low silver recovery was associated with argentojarosite formation that is resistant to cyanidation. The flowsheets for complex processing of precious and base metals sulphide flotation concentrates based on this test work results were proposed.

Jan 1, 2018

By Q. X. Li

The state discharge standard for arsenic-containing wastewater which is the first kind of pollution is less than 0.5 mg/L. In fact, in a certain company, the acidic arsenic-containing wastewater in non-ferrous smelting was as high as 860 mg/L, which is far beyond the state discharge standard. Obviously, the direct release of this wastewater without further treatment would result in great hazards to the ecological environment. To aim directly at the characteristics of acidic arsenic-containing wastewater, in this study, two steps of treatment including oxidation-flocculation and removal fluoride by mixing alkaline neutralization were suggested. Through analyzing various influencing factors in treatment effects, the optimum technical conditions were obtained. The sediments after treating were recyclable and the secondary pollutions can be avoided. Moreover, the results also show that, all indexes of the effluent after treating are lower than the First Grade Standard of Integrated Wastewater Discharge (GB 8978-1996). This novel method has advantages of short flow sheet, easy operation and low cost.

Jan 1, 2014

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By A. V. Zimin

It is a well-known fact that usage of reverse cationic flotation in magnetite ores processing enables to improve the quality of magnetite concentrates. We designed an iron ore concentrate technology (with 70 -71 % of iron) including reverse cationic flotation in pneumo-mechanical flotators RIF (developed by RIVS Corporation, Russia) with good biodegradable etheramines as collectors for flotation of quartz. Practical application of high biodegradable flotation reagents decreases environmental impact risk of objects and enterprises of mining industrial complex. This work presents results of development of flotation technology for production of high quality ferruginous concentrates from magnetite ores of Russia and Ukraine deposits. Keywords: magnetite ores, reverse cationic flotation, ferruginous concentrates, pneumatic-mechanical flotation machines, environmental impact

Sep 1, 2012

By X. Cui

Hydrocyclone is widely used in closed-circuit grinding process. However, in the first classification operation of coarse particles with high pulp density, the shortcomings of traditional cyclone are that the grinding cycle load is much high, the apex of cyclone is easily to be blocked and classification efficiency is less. Specifically, the problems of traditional cyclone used in grinding process are as follows: (1) Mill utilization factor is low and its handling capacity is small. (2) Coarse particles mixing in cyclone overflow affects the following separation process and fine particles mixing in underflow causes over-grinding, which affects the total recovery rate of valuable minerals. (3) High grinding cycle load leads to large amount of high-density slurry pumping, which causes high energy consumption and severe wear of cyclones, pipelines and pumps. The applications of new type pre-classification hydrocyclone with centrifugal volute in the first classification process of Iron Mine Mill are introduced in the paper. Pulp particles fed in the centrifugal volute were arranged in advance, so that coarse particles can be far away from the overflow pipe, which can reduce the short circuit current to avoid coarse particles entering overflow and improve classification efficiency and accuracy of cyclone. The strong points of the new cyclone in the coarse classification operation are as follows: (1) finer overflow and less fine particles mixing in underflow improves classification efficiency more than 10%; (2) lower ball mill load cycle improves ball capacity more than 10%;(3) grinding energy consumption reduces by more than 20% and cyclone feed pump reduces energy consumption by more than 12%. In short, new type pre-classification cyclone with centrifugal volute solves the problems of fine particles mixing in underflow, high grinding cycle load and less classification efficiency in the coarse classification operation. Therefore, it has broad application prospects in ferrous metal and non-ferrous metal ore dressing plant.

Sep 1, 2012

By Paulo Braga, Carlos Junior, Silvia França

"Lithium is the lightest of the metals, with high reactivity and great electrochemical potential. It has a low thermal expansion coefficient and high caloric value, and it forms very light and resistant aluminium alloys. These properties make lithium an attractive element for use in battery manufacture and glass and ceramics production, in addition to its applications in the aeronautic industry. Today, two sources of raw material are economically viable for lithium production: pegmatite rocks and brine. The world production, in 2012, was approximately 150,000 tons of LCE (lithium carbonate equivalent), almost triple the production in 2000. The forecasted consumption for the current year, 2013, was approximately 162,000 tons of LCE, and for 2020, it could be as much as 280,000 tons of LCE, stimulated essentially by the growth of world production of electric (EV), hybrid (HEV) and hybrid plug-in vehicles (PHEV), the batteries of which are based on Li-ions. With the growth of world demand and increasing prices, lithium minerals such as spodumene, petalite and amblygonite, once considered uneconomical for the production of lithium carbonate, are regaining their economic value. New projects to produce lithium compounds based on mineral sources are being developed in many countries, aiming to produce battery-grade lithium carbonate (99.95% Li2CO3). Although Brazil has large lithium pegmatite reserves, the domestic production of lithium carbonate and hydroxide is very low, at approximately 600 tons of LCE, which represents 0.4% of the world production. The application of these products is mostly in the grease and ceramic industries. The national lithium market is under government protection due to its potential use for nuclear purposes. Thus, the industrialization activities and import and export of ores and lithium minerals, as well as organic and inorganic products, such as metallic lithium and lithium alloys, are controlled by the National Commission for Nuclear Energy (Comissão Nacional de Energia Nuclear - CNEN). The objectives of this work to quantify the real lithium demand in the Brazilian market, considering that a large amount of lithium is indirectly imported in the form of the Li-ion batteries used in equipment such as mobile phones, cameras, tablets, notebooks and e-bikes, and to compare this demand with the current national production of LCE. Finally, some technological alternatives will be discussed, with the aim of increasing the competitiveness of the lithium industry in Brazil."

Jan 1, 2014

By Robert van Hille, Alison Lewis

The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pre-treatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium. The pellet reactor was used to precipitate nickel as nickel carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed. For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. For removal of cobalt as cobalt carbonate from an actual stream, a stable cobalt removal of only 60% was achieved. This was found to be due to the presence of magnesium, which reduced the cobalt precipitation efficiency through the formation of the magnesium bicarbonate ion.

Jan 1, 2003

By S. Kelebek, M. Davidson

"Flotation tests were conducted on a mixed copper ore sample containing bornite and malachite with trace quantity of other secondary copper minerals. The bornite component was very floatable, in sharp contrast to poor flotation characteristics of other copper minerals. A Box-Behnken experimental design methodology was used to study effects of three main reagents, namely potassium amyl xanthate (PAX), hydroxamate (Cytec 6494) and diethylenetriamine (DETA). Pine oil, as a frother, was used at a fixed concentration. Three main models constructed using a statistical software included malachite recovery, overall copper recovery, and copper grade. Bornite recovery was not modelled as its recovery was consistently over 99 % in the presence of hydroxamate and PAX. In each model, the hydroxamate dosage was the dominant parameter (at 95% significance level) determining the recovery of main components including that of gangue, which manifested itself by lowering the copper grade of the concentrate. In comparison, PAX was effective only at 90% significance level. DETA did not affect the overall recovery of copper or malachite significantly, but appeared to cause a significant decline in the concentrate grade, especially when used simultaneously with hydroxamate. Various quadratic models developed for the flotation system investigated are presented."

Jan 1, 2014

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By Georges Delemontex, Nigel Grigg

"Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices and currencies expose many mines to risks especially dealing with low and variable ore grades. Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue rejection, the removal of lower S.G. waste rock from the circuit, not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill. Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times. This paper explores: the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process; and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included. Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers."

Jan 1, 2014

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014